Before this changed we unconditionally fetched the MimeType. On Some
backends like s3 and swift this takes an extra transaction which meant
that `lsf` on those backends was needlessly slow.
This adds an internal option so `lsf` can declare whether it wants
MimeTypes or not depending on whether the user asked for them and an
external flag `--no-mimetype` for `lsjson`.
See: https://forum.rclone.org/t/reliably-setup-incremental-updates/14006/8
Statistics of ransfers which were interrupted are not cleared before
retry iteration. These transfers completed with over 100 percentage.
This change clears transfer accounting before next retry iteration is
done in order to keep numbers in track.
Fixes#3861
For few commands, RClone counts a error multiple times. This was fixed by
creating a new error type which keeps a flag to remember if the error has
already been counted or not. The CountError function now wraps the original
error eith the above new error type and returns it.
Before this change --update would transfer any file which was newer
than the destination regardless of whether it had changed or not.
This is needlessly wasteful of bandwidth.
After this change --update will only transfer files if they are newer
**and** they are different (checked with checksum and size).
'Couldn't find file - Need to Transfer' changed to 'Need to transfer -
File Not Found at Destination' because while reading the debug logs, it
confuses with failure in operation.
Before this change if -u/--update was in effect we compared the size
of the files to see if the transfer should go ahead. This was
comparing -1 with an actual size so the transfer always proceeded.
After this change we use the existing `sizeDiffers` function which
does the correct comparison with -1 for files of unknown length.
See: https://forum.rclone.org/t/sync-with-google-photos-to-local-drive-will-result-in-recoping/11605
Before this change we didn't calculate or check hashes of transferred
files if --size-only mode was explicitly set.
This problem was introduced in 20da3e6352 which was released with v1.37
After this change hashes are checked for all transfers unless
--ignore-checksums is set.
Before this change we calculated the checkums when using
--ignore-checksum but ignored them at the end.
Now we don't calculate the checksums at all which is more efficient.
Before this change for a post copy Hash check we would run the hashes sequentially.
Now we run the hashes in parallel for a useful speedup.
Note that this refactors the hash check in Copy to use the standard
hash checking routine.
Before this fix rclone calculated all the hashes on transfer. This
was particularly slow for the local backend.
After the fix we just calculate one hash which is enough for data
integrity.
This was factored from fstest as we were including the testing
enviroment into the main binary because of it.
This was causing opening the browser to fail because of 8243ff8bc8.
Introduce stats groups that will isolate accounting for logically
different transferring operations. That way multiple accounting
operations can be done in parallel without interfering with each other
stats.
Using groups is optional. There is dedicated global stats that will be
used by default if no group is specified. This is operating mode for CLI
usage which is just fire and forget operation.
For running rclone as rc http server each request will create it's own
group. Also there is an option to specify your own group.
This is done to make clear ownership over accounting object and prepare
for removing global stats object.
Stats elapsed time calculation has been altered to account for actual
transfer time instead of stats creation time.
We now have a backend (fichier) which doesn't support 0 length
files. Therefore all 0 length files in the tests have been replaced
with length 1.
In a future commit we will implement a test for 0 length files.
- Change rclone/fs interfaces to accept context.Context
- Update interface implementations to use context.Context
- Change top level usage to propagate context to lover level functions
Context propagation is needed for stopping transfers and passing other
request-scoped values.
Before this change, when using rclone copy or move with --backup-dir
and the source was a single file, rclone would fail to use the backup
directory.
This change looks up the backup directory in the Fs cache and uses it
as appropriate.
This affects any commands which call operations.MoveFile or
operations.CopyFile which includes rclone move/moveto/copy/copyto
where the source is a single file.
Fixes#3219
Before this change we calculated the checksum which is potentially
time consuming and then ignored the result. After the change we don't
calculate the checksum if we are about to ignore it.
In c5ac96e9e7 we made --files-from only read the objects specified and
don't scan directories.
This caused problems with Google drive (very very slow) and B2
(excessive API consumption) so it was decided to make the old
behaviour (traversing the directories) the default with --files-from
and use the existing --no-traverse flag (which has exactly the right
semantics) to enable the new non scanning behaviour.
See: https://forum.rclone.org/t/using-files-from-with-drive-hammers-the-api/8726Fixes#3102Fixes#3095
Before the fix we were only de-duping the ListR batches.
Afterwards we dedupe everything.
This will have the consequence that rclone uses more memory as it will
build a map of all the directory names, not just the names in a given
directory.
This dramatically increases the speed (7x in my tests) of the de-dupe
as google drive supports ListR directly and dedupe did not work with
`--fast-list`.
Fixes#2902
This will increase speed for backends which support ListR and will not
have the memory overhead of using --fast-list.
It also means that errors are queued until the end so as much of the
remote will be listed as possible before returning an error.
Commands affected are:
- lsf
- ls
- lsl
- lsjson
- lsd
- md5sum/sha1sum/hashsum
- size
- delete
- cat
- settier
This brings it up to par with lsjson.
This commit also reworks the framework to use ListJSON internally
which removes duplicated code and makes testing easier.
This puts a shim on the reader opened by Copy so that if an error is
returned, the reader is re-opened at the correct seek point.
This should make downloading very large files more reliable.
Before this change TestPurge would remove a container and subsequent
tests would fail because the container was still being deleted so
couldn't be created.
This was fixed by introducing an fstest.NewRunIndividual() test runner
for TestPurge which causes the test to be run on a new container.
Before this change, Purge on the fallback path would try to delete
directories starting from the root rather than the dir passed in.
Rmdirs would also attempt to delete the root.
Before this change using --files-from would scan all the directories
that the files could possibly be in causing rclone to do more work
that was necessary.
After this change, rclone constructs an in memory tree using the
--fast-list mechanism but from all of the files in the --files-from
list and without scanning any directories.
Any objects that are not found in the --files-from list are ignored
silently.
This mechanism is used for sync/copy/move (march) and all of the
listing commands ls/lsf/md5sum/etc (walk).
Before this change remotes without server side Move (eg swift, s3,
gcs) would not be able to rename files.
After it means nearly all remotes will be able to rename files on
rclone mount with the notable exceptions of b2 and yandex.
This changes checks to see if the remote can do Move or Copy then
calls `operations.Move` to do the actual move. This will do a server
side Move or Copy but won't download and re-upload the file.
It also checks to see if the destination exists first which avoids
conflicts or duplicates.
Fixes#1965Fixes#2569
--one-way argument will check that all files on source matches the files on detination,
but not the other way. For example files present on destination but not on source will not
trigger an error.
Fixes: #1526
* Implement about for:
* local, crypt, cache, drive, swift, hubic, onedrive, pcloud, dropbox
* Implement `--json` and `---full` flag for `rclone about`
* change About interface to return a Usage structure
* Remove operations.About as it is too thin an interface
* Implement Integration test
Relates to #1138 and #1564
This problem was introduced with eca99b33c0. It seems Box is the only
remote which converts time zones, so if you give it a GMT time zone,
it returns a PST time zone which represents the same instant.
This is a problem when syncing a file which just needed its modtime
set with dropbox which can't set the mod time of a file without
re-uploading it.
Before this change we would delete the file, then the server side move
would fail moving the file to the backup-dir because it no longer
existed.
After this change the destination file is moved to the backup-dir
instead of being deleted and the new file is uploaded.
Fixes#2134
The purpose of this is to make it easier to maintain and eventually to
allow the rclone backends to be re-used in other projects without
having to use the rclone configuration system.
The new code layout is documented in CONTRIBUTING.
