When a file has its modtime set while it is open we delay setting the
modtime until the file is closed.
The file is then uploaded in Flush. In Release we check the cached
file has been uploaded by comparing modtimes and or hashes and upload
it again if it has changed.
Before this change we forgot to change the time on the cached file
when we updated the time file on the object, so this mean that Release
reset the time to the wrong time and uploaded the file again on
remotes which don't support hashes (eg crypt).
The fix was to set the modtime of the cached file at the same time we
set the modtime of the remote object. This means that the files check
as identical in Release so it doesn't try to upload the file.
This means that we avoid a double upload and the modtime is correct.
See: https://forum.rclone.org/t/modification-time-with-vfs-cache/13906/8
Before this change, when uploading files from the VFS cache which were
pending a rename, rclone would use the new path of the object when
specifiying the destination remote. This didn't cause a problem with
most backends as the subsequent rename did nothing, however with the
drive backend, since it updates objects, the incorrect Remote was
embedded in the object. This caused the rename to apparently succeed
but the object be at the wrong location.
The fix for this was to make sure we upload to the path stored in the
object if available.
This problem was spotted by the new rename tests for the VFS layer.
Before this change, renaming an open file when using the VFS cache was
delayed until the file was closed. This meant that the file was not
readable after a rename even though it is was in the cache.
After this change we rename the local cache file and the in memory
cache, delaying only the rename of the file in object storage.
See: https://forum.rclone.org/t/xen-orchestra-ebadf-bad-file-descriptor-write/13104
This makes ReadAt for non cached files wait a short time (up to 5mS)
if it gets an out of order read (which would normally cause a seek and
which take a long time) to see if the gap will be filled with an in
order read.
This makes mount2 based on go-fuse work more efficiently and enables
async reading in normal mount.
A similar change was done for WriteAt in af030f74f5
Before this change, change notify polls would clear the directory
cache recursively. So uploading a file to the root would clear the
entire directory cache.
After this change we just invalidate the directory cache of the parent
directory of the item and if the item was a directory we invalidate it
too.
Before this change when we renamed a directory this cleared the
directory cache for the parent directory too.
If the directory was remaining in the same parent this wasn't
necessary and caused the empty directory to fall out of the cache.
Fixes#3597
If a file handle is duplicated with dup() and the duplicate handle is
flushed, rclone will go ahead and close the file, making the original
file handle stale. This change removes the close() call from Flush() and
replaces it with FlushWrites() so that the file only gets closed when
Release() is called. The new FlushWrites method takes care of actually
writing the file back to the underlying storage.
Fixes#3381
These objects (eg Google Docs) appear with 0 length in the VFS.
Before this change, these only read 0 bytes.
After this change, even though the size appears to be 0, the objects
can be read to the end. If the objects are read to the end then the
size on the handle will be updated.
Before this change, with --vfs-cache-mode minimal,writes if files were
opened they would always be read from the remote, regardless of
whether they were in the cache or not.
This change checks to see if the file is in the cache when opening a
file with --vfs-cache-mode >= minimal and if so then it uses it from
the cache.
This makes --vfs-cache-mode writes in particular much more
efficient. No longer is a file uploaded (with write mode) then
immediately downloaded (with read only mode).
Fixes#3330
This was factored from fstest as we were including the testing
enviroment into the main binary because of it.
This was causing opening the browser to fail because of 8243ff8bc8.
Introduce stats groups that will isolate accounting for logically
different transferring operations. That way multiple accounting
operations can be done in parallel without interfering with each other
stats.
Using groups is optional. There is dedicated global stats that will be
used by default if no group is specified. This is operating mode for CLI
usage which is just fire and forget operation.
For running rclone as rc http server each request will create it's own
group. Also there is an option to specify your own group.
This is done to make clear ownership over accounting object and prepare
for removing global stats object.
Stats elapsed time calculation has been altered to account for actual
transfer time instead of stats creation time.
- Change rclone/fs interfaces to accept context.Context
- Update interface implementations to use context.Context
- Change top level usage to propagate context to lover level functions
Context propagation is needed for stopping transfers and passing other
request-scoped values.
This makes WriteAt for non cached files wait a short time if it gets
an out of order write (which would normally cause an error) to see if
the gap will be filled with an in order write.
The makes the SFTP backend work fine with --vfs-cache-mode off
Before this change we locked the root directory, recursively fetched
the listing, applied it then unlocked the root directory.
After this change we recursively fetch the listing then apply it with
the root directory locked which shortens the time that the root
directory is locked greatly.
With the original method and the new method the subdirectories are
left unlocked and so potentially could be changed leading to
inconsistencies. This change makes the potential for inconsistencies
slightly worse by leaving the root directory unlocked at a gain of a
much more responsive system while runing vfs/refresh.
See: https://forum.rclone.org/t/rclone-rc-vfs-refresh-locking-directory-being-refreshed/9004
Before this change when doing Mkdir the VFS layer could add the new
item to an unread directory which caused confusion.
It could also do mkdir on a file when run on a bucket based remote
which would temporarily overwrite the file with a directory.
Fixes#2993
This fixes FreeBSD which seems to call SetAttr with a size even on
read only files.
This is probably a bug in the FreeBSD FUSE implementation as it
happens with mount and cmount.
See: https://forum.rclone.org/t/freebsd-question/8662/12
Previously to this change, backends without the optional interface
DirMove could not rename directories.
This change uses the new operations.DirMove call to implement renaming
directories which will fall back to Move/Copy as necessary.
Before this change, renaming and deleting of open files (which can
easily happen due to the asynchronous nature of file systems) would
produce an error, for example saving files with Firefox.
After this change we open files with the flags necessary for open
files to be renamed or deleted.
Fixes#2730
