Before this fix, rclone would sometimes hang in vfs.readAt().
This was due to a race condition causing rclone to miss the timeout
signal.
This was fixed by a small amount of extra locking.
This very likely also fixes a number of "failed to wait for
in-sequence read" errors.
The tests are now run for the mount commands and for the plain VFS.
This makes the tests much easier to debug when running with a VFS than
through a mount.
In
54deb01f00 vfs: Make OpenFile and friends return EINVAL if O_RDONLY and O_TRUNC
The generated file open_test.go was edited directly without editing
the generator.
This commit brings the generator make_open_tests.go back into line
with that edit. It also makes it so `go generate` can be used to
regenerate the tests.
Previously we were using f which calls f.String() which calls f.Path()
which can cause a deadlock if uses carelessly.
This patch explicitly calls f.Path() or f._path() to bring attention
to the fact that there is a call to a method.
As part of this we take a copy of the directory path as calling
d.Path() violates the total locking order.
See the comment at the top of file.go for details
--vfs-read-wait duration Time to wait for in-sequence read before seeking. (default 5ms)
--vfs-write-wait duration Time to wait for in-sequence write before giving error. (default 1s)
See: https://forum.rclone.org/t/constantly-high-iowait-add-log/14156
When a file has its modtime set while it is open we delay setting the
modtime until the file is closed.
The file is then uploaded in Flush. In Release we check the cached
file has been uploaded by comparing modtimes and or hashes and upload
it again if it has changed.
Before this change we forgot to change the time on the cached file
when we updated the time file on the object, so this mean that Release
reset the time to the wrong time and uploaded the file again on
remotes which don't support hashes (eg crypt).
The fix was to set the modtime of the cached file at the same time we
set the modtime of the remote object. This means that the files check
as identical in Release so it doesn't try to upload the file.
This means that we avoid a double upload and the modtime is correct.
See: https://forum.rclone.org/t/modification-time-with-vfs-cache/13906/8
Before this change, when uploading files from the VFS cache which were
pending a rename, rclone would use the new path of the object when
specifiying the destination remote. This didn't cause a problem with
most backends as the subsequent rename did nothing, however with the
drive backend, since it updates objects, the incorrect Remote was
embedded in the object. This caused the rename to apparently succeed
but the object be at the wrong location.
The fix for this was to make sure we upload to the path stored in the
object if available.
This problem was spotted by the new rename tests for the VFS layer.
Before this change, renaming an open file when using the VFS cache was
delayed until the file was closed. This meant that the file was not
readable after a rename even though it is was in the cache.
After this change we rename the local cache file and the in memory
cache, delaying only the rename of the file in object storage.
See: https://forum.rclone.org/t/xen-orchestra-ebadf-bad-file-descriptor-write/13104
This makes ReadAt for non cached files wait a short time (up to 5mS)
if it gets an out of order read (which would normally cause a seek and
which take a long time) to see if the gap will be filled with an in
order read.
This makes mount2 based on go-fuse work more efficiently and enables
async reading in normal mount.
A similar change was done for WriteAt in af030f74f5
Before this change, change notify polls would clear the directory
cache recursively. So uploading a file to the root would clear the
entire directory cache.
After this change we just invalidate the directory cache of the parent
directory of the item and if the item was a directory we invalidate it
too.
Before this change when we renamed a directory this cleared the
directory cache for the parent directory too.
If the directory was remaining in the same parent this wasn't
necessary and caused the empty directory to fall out of the cache.
Fixes#3597
If a file handle is duplicated with dup() and the duplicate handle is
flushed, rclone will go ahead and close the file, making the original
file handle stale. This change removes the close() call from Flush() and
replaces it with FlushWrites() so that the file only gets closed when
Release() is called. The new FlushWrites method takes care of actually
writing the file back to the underlying storage.
Fixes#3381
These objects (eg Google Docs) appear with 0 length in the VFS.
Before this change, these only read 0 bytes.
After this change, even though the size appears to be 0, the objects
can be read to the end. If the objects are read to the end then the
size on the handle will be updated.
