shorewall6-lite 8 shorewall6-lite Administration tool for Shoreline 6 Firewall Lite (Shorewall6 Lite) shorewall6-lite trace|debugnolock -options add interface[:host-list] zone shorewall6-lite trace|debugnolock -options allow address shorewall6-lite trace|debugnolock -options clear-f shorewall6-lite trace|debugnolock -options delete interface[:host-list] zone shorewall6-lite trace|debugnolock -options disable { interface | provider } shorewall6-lite trace|debugnolock -options drop address shorewall6-lite trace|debug -options dump -x -l -m shorewall6-lite trace|debugnolock -options enable { interface | provider } shorewall6-lite trace|debugnolock -options forget filename shorewall6-lite trace|debug -options help shorewall6-lite trace|debug -options hits-t shorewall6-lite trace|debug -options ipcalc address mask address/vlsm shorewall6-lite trace|debug -options iprange address1-address2 shorewall6-lite trace|debug -options iptrace iptables match expression shorewall6-lite trace|debugnolock -options logdrop address shorewall6-lite trace|debug -options logwatch -m refresh-interval shorewall6-lite trace|debugnolock -options logreject address shorewall6-lite trace|debug -options noiptrace iptables match expression shorewall6-lite trace|debugnolock -options reject address shorewall6-lite trace|debugnolock -options reset shorewall6-lite trace|debugnolock -options restart -n -p directory shorewall6-lite trace|debugnolock -options restore filename shorewall6-lite trace|debugnolock -options save filename shorewall6-lite trace|debug -options show -b -x -l -t {filter|mangle|nat|raw|rawpost} chainchain shorewall6-lite trace|debug -options show -f capabilities shorewall6-lite trace|debug -options show classifiers|connections|config|filters|ip|ipa|zones|policies|marks shorewall6-lite trace|debug -options show -x mangle|nat|routing|raw|rawpost shorewall6-lite trace|debug -options show tc shorewall6-lite trace|debug -options show -m log shorewall6-lite trace|debugnolock -options start -n -p shorewall6-lite trace|debugnolock -options stop shorewall6-lite trace|debug -options status shorewall6-lite trace|debug -options version-a The shorewall6-lite utility is used to control the Shoreline Firewall Lite (Shorewall Lite). The trace and debug options are used for debugging. See http://www.shorewall.net/starting_and_stopping_shorewall.htm#Trace. The nolock option prevents the command from attempting to acquire the shorewall6-lite lockfile. It is useful if you need to include shorewall commands in /etc/shorewall/started. The options control the amount of output that the command produces. They consist of a sequence of the letters v and q. If the options are omitted, the amount of output is determined by the setting of the VERBOSITY parameter in shorewall6.conf(5). Each v adds one to the effective verbosity and each q subtracts one from the effective VERBOSITY. Anternately, v may be followed immediately with one of -1,0,1,2 to specify a specify VERBOSITY. There may be no white space between v and the VERBOSITY. The options may also include the letter t which causes all progress messages to be timestamped. The available commands are listed below. add Adds a list of hosts or subnets to a dynamic zone usually used with VPN's. The interface argument names an interface defined in the shorewall-interfaces(5) file. A host-list is comma-separated list whose elements are host or network addresses. The add command is not very robust. If there are errors in the host-list, you may see a large number of error messages yet a subsequent shorewall6-lite show zones command will indicate that all hosts were added. If this happens, replace add by delete and run the same command again. Then enter the correct command. allow Re-enables receipt of packets from hosts previously blacklisted by a drop, logdrop, reject, or logreject command. clear Clear will remove all rules and chains installed by shorewall6-lite. The firewall is then wide open and unprotected. Existing connections are untouched. Clear is often used to see if the firewall is causing connection problems. If -f is given, the command will be processed by the compiled script that executed the last successful start, restart or refresh command if that script exists. delete The delete command reverses the effect of an earlier add command. The interface argument names an interface defined in the shorewall-interfaces(5) file. A host-list is comma-separated list whose elements are a host or network address. disable Added in Shorewall 4.4.26. Disables the optional provider associated with the specified interface or provider. Where more than one provider share a single network interface, a provider name must be given. drop Causes traffic from the listed addresses to be silently dropped. dump Produces a verbose report about the firewall configuration for the purpose of problem analysis. The -x option causes actual packet and byte counts to be displayed. Without that option, these counts are abbreviated. The -m option causes any MAC addresses included in shorewall6-lite log messages to be displayed. The -l option causes the rule number for each Netfilter rule to be displayed. enable Added in Shorewall 4.4.26. Enables the optional provider associated with the specified interface or provider. Where more than one provider share a single network interface, a provider name must be given. forget Deletes /var/lib/shorewall6-lite/filename and /var/lib/shorewall6-lite/save. If no filename is given then the file specified by RESTOREFILE in shorewall6.conf(5) is assumed. help Displays a syntax summary. hits Generates several reports from shorewall6-lite log messages in the current log file. If the -t option is included, the reports are restricted to log messages generated today. ipcalc Ipcalc displays the network address, broadcast address, network in CIDR notation and netmask corresponding to the input[s]. iprange Iprange decomposes the specified range of IP addresses into the equivalent list of network/host addresses. iptrace This is a low-level debugging command that causes iptables TRACE log records to be created. See iptables(8) for details. The iptables match expression must be one or more matches that may appear in both the raw table OUTPUT and raw table PREROUTING chains. The trace records are written to the kernel's log buffer with faciility = kernel and priority = warning, and they are routed from there by your logging daemon (syslogd, rsyslog, syslog-ng, ...) -- shorewall6-lite has no control over where the messages go; consult your logging daemon's documentation. logdrop Causes traffic from the listed addresses to be logged then discarded. Logging occurs at the log level specified by the BLACKLIST_LOGLEVEL setting in shorewall6.conf (5). logwatch Monitors the log file specified by the LOGFILE option in shorewall6.conf(5) and produces an audible alarm when new shorewall6-lite messages are logged. The -m option causes the MAC address of each packet source to be displayed if that information is available. The refresh-interval specifies the time in seconds between screen refreshes. You can enter a negative number by preceding the number with "--" (e.g., shorewall6-lite logwatch -- -30). In this case, when a packet count changes, you will be prompted to hit any key to resume screen refreshes. logreject Causes traffic from the listed addresses to be logged then rejected. Logging occurs at the log level specified by the BLACKLIST_LOGLEVEL setting in shorewall6.conf (5). noiptrace This is a low-level debugging command that cancels a trace started by a preceding iptrace command. The iptables match expression must be one given in the iptrace command being cancelled. reset All the packet and byte counters in the firewall are reset. restart Restart is similar to shorewall6-lite start except that it assumes that the firewall is already started. Existing connections are maintained. The -n option causes shorewall6-lite to avoid updating the routing table(s). The -p option causes the connection tracking table to be flushed; the conntrack utility must be installed to use this option. restore Restore shorewall6-lite to a state saved using the shorewall6-lite save command. Existing connections are maintained. The filename names a restore file in /var/lib/shorewall6-lite created using shorewall6-lite save; if no filename is given then shorewall6-lite will be restored from the file specified by the RESTOREFILE option in shorewall6.conf(5). save The dynamic blacklist is stored in /var/lib/shorewall6-lite/save. The state of the firewall is stored in /var/lib/shorewall6-lite/filename for use by the shorewall6-lite restore. If filename is not given then the state is saved in the file specified by the RESTOREFILE option in shorewall6.conf(5). show The show command can have a number of different arguments: capabilities Displays your kernel/iptables capabilities. The -f option causes the display to be formatted as a capabilities file for use with compile -e. [ [ chain ] chain... ] The rules in each chain are displayed using the iptables -L chain -n -v command. If no chain is given, all of the chains in the filter table are displayed. The -x option is passed directly through to iptables and causes actual packet and byte counts to be displayed. Without this option, those counts are abbreviated. The -t option specifies the Netfilter table to display. The default is filter. The -b ('brief') option causes rules which have not been used (i.e. which have zero packet and byte counts) to be omitted from the output. Chains with no rules displayed are also omitted from the output. The -l option causes the rule number for each Netfilter rule to be displayed. If the t option and the chain keyword are both omitted and any of the listed chains do not exist, a usage message is displayed. classifiers|filters Displays information about the packet classifiers defined on the system as a result of traffic shaping configuration. config Dispays distribution-specific defaults. connections Displays the IP connections currently being tracked by the firewall. ip Displays the system's IPv4 configuration. ipa Added in Shorewall 4.4.17. Displays the per-IP accounting counters (shorewall-accounting (5)). log Displays the last 20 shorewall6-lite messages from the log file specified by the LOGFILE option in shorewall6.conf(5). The -m option causes the MAC address of each packet source to be displayed if that information is available. marks Added in Shorewall 4.4.26. Displays the various fields in packet marks giving the min and max value (in both decimal and hex) and the applicable mask (in hex). nat Displays the Netfilter nat table using the command iptables -t nat -L -n -v.The -x option is passed directly through to iptables and causes actual packet and byte counts to be displayed. Without this option, those counts are abbreviated. policies Added in Shorewall 4.4.4. Displays the applicable policy between each pair of zones. Note that implicit intrazone ACCEPT policies are not displayed for zones associated with a single network where that network doesn't specify routeback. routing Displays the system's IPv4 routing configuration. raw Displays the Netfilter raw table using the command iptables -t raw -L -n -v.The -x option is passed directly through to iptables and causes actual packet and byte counts to be displayed. Without this option, those counts are abbreviated. tc Displays information about queuing disciplines, classes and filters. zones Displays the current composition of the Shorewall zones on the system. start Start Shorewall Lite. Existing connections through shorewall6-lite managed interfaces are untouched. New connections will be allowed only if they are allowed by the firewall rules or policies. The -p option causes the connection tracking table to be flushed; the conntrack utility must be installed to use this option. stop Stops the firewall. All existing connections, except those listed in shorewall-routestopped(5) or permitted by the ADMINISABSENTMINDED option in shorewall6.conf(5), are taken down. The only new traffic permitted through the firewall is from systems listed in shorewall-routestopped(5) or by ADMINISABSENTMINDED. If -f is given, the command will be processed by the compiled script that executed the last successful start, restart or refresh command if that script exists. status Produces a short report about the state of the Shorewall-configured firewall. version Displays Shorewall's version. The -a option is included for compatibility with earlier Shorewall releases and is ignored. /etc/shorewall6-lite/ http://www.shorewall.net/starting_and_stopping_shorewall.htm shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall_interfaces(5), shorewall6-ipsets(5), shorewall6-maclist(5), shorewall6-masq(5), shorewall6-netmap(5), shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5), shorewall6-proxyarp(5), shorewall6-rtrules(5), shorewall6-routestopped(5), shorewall6-rules(5), shorewall6.conf(5), shorewall6-secmarks(5), shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-tcrules(5), shorewall6-tos(5), shorewall6-tunnels(5), shorewall6-zones(5)