Shorewall 2.5.7. Problems Corrected in 2.5.7: 1) In previous versions, when the command is 'start', 'restart' or 'stop' then OUTPUT traffic to hosts listed in /etc/shorewall/routestopped is not enabled if ADMINISABSENTMINDED=Yes. That traffic is now enabled independent of the setting of ADMINISABSENTMINDED. Problems Corrected in 2.5.6: 1) The following fatal error could occur at startup: ERROR: Command "/sbin/iptables -A INPUT -j LOG --log-level NONE --log-prefix "Shorewall:INPUT:ACCEPT:"" Failed That problem has been corrected. 2) The Makefile is now unconditionally installed in /etc/shorewall during an upgrade (the prior copy has been saved in /etc/shorewall-.bkout/Makefile). New Features in 2.5.6: 1) The install.sh script now does a much cleaner job of backing up the current installation. It copies the directories /etc/shorewall, /usr/share/shorewall and /var/lib/shorewall to a directory of the same name with "-$VERSION.bkout" appended. The init script and /sbin/shorewall are backed up to the /usr/share/shorewall and /var/lib/shorewall directories respectively. This makes it very simple to remove the backups: rm -rf /etc/shorewall-*.bkout rm -rf /usr/share/shorewall-*.bkout rm -rf /var/lib/shorewall-*.bkout 2) A new '-n' option has been added to the "start", "restart", "restore", "stop" and "try" commands. This option instructs Shorewall to not alter the routing in any way. This option is useful when you have a multi-ISP environment because it prevents the route cache from being flushed which preserves the mapping of end-point address pairs to routes. Problems Corrected in 2.5.5: 1) The install script now installs the correct Makefile. Previously, the /etc/shorewall/actions file was identical to the Makefile. 2) Error Handling was completely broken; operations such as "shorewall start" would continue after what should have been fatal errors. Problems Corrected in 2.5.4: 1) Several serious problems associated with macros have been corrected. Problems Corrected in 2.5.3: 1) The Netfilter 'raw' table is now cleared during "shorewall stop", "shorewall [re]start" and "shorewall clear". Problems Corrected in 2.5.2: 1) You may now include port lists in in the /etc/shorewall/accounting file. 2) The packet type match capability is now correctly reported when PKTTYPE=No in /etc/shorewall/shorewall.conf. Problems Corrected in 2.5.1: 1) Shorewall is no longer dependent on the 'which' utility. 2) "shorewall add" no longer fails when the 'ipsec' option has appeared in /etc/shorewall/hosts. 3) The Makefile has been changed to compare the modification times of the files in /etc/shorewall with /var/lib/shorewall/restore-base. That file is modified each time that Shorewall is [re]started whereas /var/lib/shorewall/restarted is also modified by "shorewall reset" and "shorewall refresh". 4) The handling of log levels passed to macros has been corrected. Previously, passing a log level to a macro resulted in a [re]start error. Problems Corrected in 2.5.0: 1) The behavior of CONTINUE policies has been improved. Shorewall no longer generates a useless policy chain corresponding to these policies. 2) The combining of the zones and ipsec files has now been made upward compatible provided that the user doesn't do something idiotic such as install the new shorewall.conf file then manually update it with exactly the changes that had been applied to the old file. Migration Considerations: 1) The "monitor" command has been eliminated. 2) The "DISPLAY" and "COMMENTS" columns in the /etc/shorewall/zones file have been removed and have been replaced by the former columns of the /etc/shorewall/ipsec file. The latter file has been removed. Additionally the FW option in shorewall.conf has been deprecated and is no longer set to 'fw' by default. New users are expected to define the firewall zone in /etc/shorewall/zones. Adhering to the principle of least astonishment, the old /etc/shorewall/ipsec file will continue to be supported. A new IPSECFILE variable in /etc/shorewall/shorewall.conf determines the name of the file that Shorewall looks in for IPSEC information. If that variable is not set or is set to the empty value then IPSECFILE=ipsec is assumed. So if you simply upgrade and don't do something idiotic like replace your current shorewall.conf file with the new one, your old configuration will continue to work. A dummy 'ipsec' file is included in the release so that your package manager (e.g., rpm) won't remove your existing file. The shorewall.conf file included in this release sets IPSECFILE=zones so that new users are expected to use the new zone file format. As a result, the columns in the /etc/shorewall/zones file are now as follows: ZONE Short name of the zone (5 Characters or less in length). The names "all" and "none" are reserved and may not be used as zone names. Where a zone is nested in one or more other zones, you may follow the (sub)zone name by ":" and a comma-separated list of the parent zones. The parent zones must have been defined in earlier records in this file. Example: #ZONE TYPE OPTIONS a plain b plain c:a,b plain Currently, Shorewall uses this information only to reorder the zone list so that parent zones appear after their subzones in the list. In the future, Shorewall may make more extensive use of that information. TYPE plain - This is the standard Shorewall zone type and is the default if the column is left empty or if it is entered as "-". Communication with some zone hosts may be encrypted. Encrypted hosts are designated using the 'ipsec' option in /etc/shorewall/hosts. ipsec - Communication with all zone hosts is encrypted Your kernel and iptables must include policy match support. firewall - Designates the firewall itself. You must have exactly one 'firewall' zone. No options are permitted with a 'firewall' zone. OPTIONS, A comma-separated list of options as IN OPTIONS, follows: OUT OPTIONS reqid= where is specified using setkey(8) using the 'unique: option for the SPD level. spi= where is the SPI of the SA used to encrypt/decrypt packets. proto=ah|esp|ipcomp mss= (sets the MSS field in TCP packets) mode=transport|tunnel tunnel-src=
[/] (only available with mode=tunnel) tunnel-dst=
[/] (only available with mode=tunnel) strict Means that packets must match all rules. next Separates rules; can only be used with strict.. Example: mode=transport,reqid=44 The options in the OPTIONS column are applied to both incoming and outgoing traffic. The IN OPTIONS are applied to incoming traffic (in addition to OPTIONS) and the OUT OPTIONS are applied to outgoing traffic. If you wish to leave a column empty but need to make an entry in a following column, use "-". THE ORDER OF THE ENTRIES IN THIS FILE IS IMPORTANT IF YOU HAVE NESTED OR OVERLAPPING ZONES DEFINED THROUGH /etc/shorewall/hosts. 3) The DROPINVALID option has been removed from shorewall.conf. The behavior will be as if DROPINVALID=No had been specified. If you wish to drop invalid state packets, use the dropInvalid built-in action. 4) The 'nobogons' interface and hosts option as well as the BOGON_LOG_LEVEL option have been eliminated. 5) Most of the standard actions have been replaced by parameterized macros (see below). So for example, the action.AllowSMTP and action.DropSMTP have been removed an a parameterized macro macro.SMTP has been added to replace them. In order that current users don't have to immediately update their rules and user-defined actions, Shorewall can substitute an invocation of the a new macro for an existing invocation of one of the old actions. So if your rules file calls AllowSMTP, Shorewall will replace that call with SMTP/ACCEPT. Because this substitution is expensive, it is conditional based on the setting of MAPOLDACTIONS in shorewall.conf. If this option is set to YES or if it is not set (such as if you are using your old shorewall.conf file) then Shorewall will perform the substitution. Once you have converted to use the new macros, you can set MAPOLDACTIONS=No and invocations of those actions will go much quicker during 'shorewall [re]start'. 6) The STATEDIR variable in /etc/shorewall/shorewall.conf has been removed. STATEDIR is now fixed at /var/lib/shorewall. If you have previously set STATEDIR to another directory, please copy the files from that directory to /var/lib/shorewall/ before [re]starting Shorewall after the upgrade to this version. 7) The "shorewall status" command now just gives the status of Shorewall (started or not-started). The previous status command has been renamed "dump". The command also shows the state relative to the state diagram at http://shorewall.net/starting_and_stopping_shorewall.htm. In addition to the state, the time and date at which that state was entered is shown. Note that at least one "shorewall [re]start" must be issued after upgrading to this release before "shorewall status" will show anything but "Unknown" for the state. 8) The "shorewall forget" command now removes the dynamic blacklist save file (/var/lib/shorewall/save). 9) In previous versions of Shorewall, the rules generated by entries in /etc/shorewall/tunnels preceded those rules generated by entries in /etc/shorewall/rules. Beginning with this release, the rules generated by entries in the tunnels file will appear *AFTER* the rules generated by the rules file. This may cause you problems if you have REJECT, DENY or CONTINUE rules in your rules file that would cause the tunnel transport packets to not reach the rules that ACCEPT them. See http://www.shorewall.net/VPNBasics.html for information on the rules generated by entries in the tunnels file. 10) In previous releases, the "refresh" command could source your tcstart script. Beginning with this release, "refresh" will run that script if it is executable but will not source it. Users of third-party TC scripts like WonderShaper should see no change provided that execute permission is placed on /etc/shorewall/tcstart. New Features in Shorewall 2.5.* 1) Error and warning messages are made easier to spot by using capitalization (e.g., ERROR: and WARNING:). 2) A new option 'critical' has been added to /etc/shorewall/routestopped. This option can be used to enable communication with a host or set of hosts during the entire "shorewall [re]start/stop" process. Listing a host with this option differs from listing it without the option in several ways: a) The option only affect traffic between the listed host(s) and the firewall itself. b) If there are any entries with 'critical', the firewall will be completely opened briefly during start, restart and stop but there will be no chance of any packets to/from the listed host(s) being dropped or rejected. Possible uses for this option are: a) Root fileset is NFS mounted. You will want to list the NFS server in the 'critical' option. b) You are running Shorewall in a Crossbeam environment (www.crossbeam.com). You will want to list the Crossbeam interface in this option 3) A new 'macro' feature has been added. Macros are very similar to actions and can be used in similar ways. The differences between actions and macros are as follows: a) An action creates a separate chain with the same name as the action (when logging is specified on the invocation of an action, a chain beginning with "%" followed by the name of the action and possibly followed by a number is created). When a macro is invoked, it is expanded in-line and no new chain is created. b) An action may be specified as the default action for a policy; macros cannot be specified this way. c) Actions must be listed in either /usr/share/shorewall/actions.std or in /etc/shorewall/actions. Macros are defined simply by placing their definition file in the CONFIG_PATH. d) Actions are defined in a file with a name beginning with "action." and followed by the name of the action. Macro files are defined in a file with a name beginning with "macro.". e) Actions may invoke other actions. Macros may not directly invoke other macros although they may invoke other macros indirectly through an action. f) DNAT[-] and REDIRECT[-] rules may not appear in an action. They are allowed in a macro with the restriction that the a macro containing one of these rules may not be invoked from an action. g) The values specified in the various columns when you invoke a macro are substituted in the corresponding column in each rule in the macro. The first three columns get special treatment: ACTION If you code PARAM as the action in a macro then when you invoke the macro, you can include the name of the macro followed by a slash ("/") and an ACTION (either builtin or user-defined. All instances of PARAM in the body of the macro will be replaced with the ACTION. Any logging applied when the macro is invoked is applied following the same rules as for actions. SOURCE and DEST If the rule in the macro file specifies a value and the invocation of the rule also specifies a value then the value in the invocation is appended to the value in the rule using ":" as a separator. Example: /etc/shorewall/macro.SMTP PARAM - loc tcp 25 /etc/shorewall/rules: SMTP/DNAT:info net 192.168.1.5 Would be equivalent to the following in the rules file: DNAT:info net loc:192.168.1.5 tcp 25 Rest Any value in the invocation replaces the value in the rule in the macro. One additional restriction applies to the mixing of macros and actions. Macros that are invoked from actions cannot themselves invoke other actions. 4) If you have 'make' installed on your firewall, then when you use the '-f' option to 'shorewall start' (as happens when you reboot), if your /etc/shorewall/ directory contains files that were modified after Shorewall was last restarted then Shorewall is started using the config files rather than using the saved configuration. 5) The 'arp_ignore' option has been added to /etc/shorewall/interfaces entries. This option sets /proc/sys/net/ipv4/conf//arp_ignore. By default, the option sets the value to 1. You can also write arp_ignore= where value is one of the following: 1 - reply only if the target IP address is local address configured on the incoming interface 2 - reply only if the target IP address is local address configured on the incoming interface and both with the sender's IP address are part from same subnet on this interface 3 - do not reply for local addresses configured with scope host, only resolutions for global and link addresses are replied 4-7 - reserved 8 - do not reply for all local addresses WARNING -- DO NOT SPECIFY arp_ignore FOR ANY INTERFACE INVOLVED IN PROXY ARP. 6) In /etc/shorewall/rules, "all+" in the SOURCE or DEST column works like "all" but also includes intrazone traffic. So the rule: ACCEPT loc all+ tcp 22 would allow SSH traffic from loc->loc whereas ACCEPT loc all tcp 22 does not. 7) A new FASTACCEPT option has been added to shorewall.conf. Normally, Shorewall accepting ESTABLISHED/RELATED packets until these packets reach the chain in which the original connection was accepted. So for packets going from the 'loc' zone to the 'net' zone, ESTABLISHED/RELATED packets are ACCEPTED in the 'loc2net' chain. If you set FASTACCEPT=Yes, then ESTABLISHED/RELEATED packets are accepted early in the INPUT, FORWARD and OUTPUT chains. If you set FASTACCEPT=Yes then you may not include rules in the ESTABLISHED or RELATED sections of /etc/shorewall/rules. 8) Shorewall now generates an error if the 'norfc1918' option is specified for an interface with an RFC 1918 address. 9) You may now specify "!" followed by a list of addresses in the SOURCE and DEST columns of entries in /etc/shorewall/rules, /etc/shorewall/tcrules and in action files and Shorewall will generate the rule that you expect. Example 1 (/etc/shorewall/rules): #ACTION SOURCE DEST PROTO DEST PORT(S) ACCEPT loc:!192.168.1.0/24,10.0.0.0/8 net tcp 80 That rule would allow loc->net HTTP access except for the local networks 192.168.1.0/24 and 10.0.0.0/8. Example 2 (/etc/shorewall/rules): #ACTION SOURCE DEST PROTO DEST PORT(S) ACCEPT loc:10.0.0.0/24!10.0.0.4,10.0.0.22 \ net tcp 80 That rule would allow loc->net HTTP access from the local network 10.0.0.0/24 except for hosts 10.0.0.4 and 10.0.0.22. 10) You may now specify "!" followed by a list of addresses in the SOURCE and DEST columns of entries in /etc/shorewall/tcrules and Shorewall will generate the rule that you expect. 11) Tunnel types "openvpnserver" and "openvpnclient" have been added to reflect the introduction of client and server OpenVPN configurations in OpenVPN 2.0. 12) The COMMAND variable is now set to 'restore' in restore scripts. The value of this variable is sometimes of interest to programmers providing custom /etc/shorewall/tcstart scripts. 13) Previously, if you defined any intra-zone rule(s) then any traffic not matching the rule(s) was subject to normal policies (which usually turned out to involve the all->all REJECT policy). Now, the intra-zone ACCEPT policy will still be in effect in the presense of intra-zone rules. That policy can still be overridden by an explicit policy in your /etc/shorewall/policy file. Example: /etc/shorewall/rules: DNAT loc:!192.168.1.4 loc:192.168.1.4:3128 tcp 80 Any other loc->loc traffic will still be accepted. If you want to also log that other loc->loc traffic at the info log level then insert this into /etc/shorewall/policy: #SOURCE DEST POLICY LOG LEVEL loc loc ACCEPT info 14) Prior to Shorewall 2.5.3, the rules file only controlled packets in the Netfilter states NEW and INVALID. Beginning with this release, the rules file can also deal with packets in the ESTABLISHED and RELATED states. The /etc/shorewall/rules file may now be divided into "sections". Each section is introduced by a line that begins with the keyword SECTION followed by the section name. Sections are as listed below and must appear in the order shown. ESTABLISHED Rules in this section apply to packets in the ESTABLISHED state. RELATED Rules in this section apply to packets in the RELATED state. NEW Rules in this section apply to packets in the NEW and INVALID states. Rules in the ESTABLISHED and RELATED sections are limited to the following ACTIONs: ACCEPT, DROP, REJECT, QUEUE, LOG and User-defined actions. Macros may be used in these sections provided that they expand to only these ACTIONs. At the end of the ESTABLISHED and RELATED sections, there is an implicit "ALLOW all all all" rule. RESTRICTION: If you specify FASTACCEPT=Yes in /etc/shorewall.shorewall.conf then the ESTABLISHED and RELATED sections must be empty. 15) The value 'ipp2p' is once again allowed in the PROTO column of the rules file. It is recommended that rules specifying 'ipp2p' only be included in the ESTABLISHED section of the file. 16) Shorewall actions lack a generalized way to pass parameters to an extension script associated with an action. To work around this lack, some users have used the log tag as a parameter. This works but requires that a log level other than 'none' be specified when the action is invoked. Beginning with this release, you can invoke an action with 'none'. Example: #ACTION SOURCE DEST A:none:these,are,parameters $FW net When /etc/shorewall/A is invoked, the LEVEL variable will be empty but the TAG variable will contain "these,are,parameters" which can be easily parsed to isolate "these", "are" and "parameters": ifs=$IFS IFS=, set -- $TAG IFS=$ifs Now, $1 = these, $2 = are and $3 = parameters 17) The "shorewall check" command now checks the /etc/shorewall/masq, /etc/shorewall/blacklist, /etc/shorewall/proxyarp, /etc/shorewall/nat and /etc/shorewall/providers files. 18) Arne Bernin's "tc4shorewall" package has been integrated into Shorewall. Arne will be providing documentation and support for this part of Shorewall. Thanks, Arne! 19) When /usr/share/shorewall/functions is loaded it now sets SHOREWALL_LIBRARY=Loaded Application code such as /etc/shorewall/tcstart may test that variable to determine if the library has been loaded into the current shell process.