Tom Eastep 2009 2010 Thomas M. Eastep Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover, and with no Back-Cover Texts. A copy of the license is included in the section entitled GNU Free Documentation License.

Traffic shaping and control was originally introduced into Shorewall in version 2.2.5. That facility was based on Arne Bernin's tc4shorewall and is generally felt to be complex and difficult to use. In Shorewall 4.5.0, a second traffic shaping facility that is simple to understand and to configure was introduced. This newer facility is described in this document while the original facility is documented in Complex Traffic Shaping/Control.

Simple traffic shaping is enabled by setting TC_ENABLED=Simple in shorewall.conf(5). You then add an entry for your external interface to shorewall-tcinterfaces(5) (/etc/shorewall/tcinterfaces). Assuming that your external interface is eth0: #INTERFACE TYPE IN-BANDWIDTH eth0 External With this simple configuration, packets to be sent through interface eth0 will be assigned to a priority band based on the value of their TOS field: TOS Bits Means Linux Priority BAND ------------------------------------------------------------ 0x0 0 Normal Service 0 Best Effort 2 0x2 1 Minimize Monetary Cost 1 Filler 3 0x4 2 Maximize Reliability 0 Best Effort 2 0x6 3 mmc+mr 0 Best Effort 2 0x8 4 Maximize Throughput 2 Bulk 3 0xa 5 mmc+mt 2 Bulk 3 0xc 6 mr+mt 2 Bulk 3 0xe 7 mmc+mr+mt 2 Bulk 3 0x10 8 Minimize Delay 6 Interactive 1 0x12 9 mmc+md 6 Interactive 1 0x14 10 mr+md 6 Interactive 1 0x16 11 mmc+mr+md 6 Interactive 1 0x18 12 mt+md 4 Int. Bulk 2 0x1a 13 mmc+mt+md 4 Int. Bulk 2 0x1c 14 mr+mt+md 4 Int. Bulk 2 0x1e 15 mmc+mr+mt+md 4 Int. Bulk 2 When dequeueing, band 1 is tried first and only if it did not deliver a packet does the system try band 2, and so onwards. Maximum reliability packets should therefore go to band 1, minimum delay to band 2 and the rest to band 3. If you run both an IPv4 and an IPv6 firewall on your system, you should define each interface in only one of the two configurations.

The default mapping of TOS to bands can be changed using the TC_PRIOMAP setting in shorewall.conf(5). The default setting of this option is: TC_PRIOMAP="2 3 3 3 2 3 1 1 2 2 2 2 2 2 2 2" These entries map Linux Priority to priority BAND. So only entries 0, 1, 2, 4 and 6 in the map are relevant to TOS->BAND mapping. Further customizations can be defined in shorewall-tcpri(5) (/etc/shorewall/tcpri). Using that file, you can: Assign traffic entering the firewall on a particular interface to a specific priority band: #BAND PROTO PORT(S) ADDRESS INTERFACE HELPER 2 - - - eth1 In this example, traffic from eth1 will be assigned to priority band 2. When an INTERFACE is specified, the PROTO, PORT(S) and ADDRESS column must contain '-'. Assign traffic from a particular IP address to a specific priority band: #BAND PROTO PORT(S) ADDRESS INTERFACE HELPER 1 - - 192.168.1.44 In this example, traffic from 192.168.1.44 will be assigned to priority band 1. When an ADDRESS is specified, the PROTO, PORT(S) and INTERFACE columns must be empty. Assign traffic to/from a particular application to a specific priority band: #BAND PROTO PORT(S) ADDRESS INTERFACE HELPER 1 udp 1194 In that example, OpenVPN traffic is assigned to priority band 1. Assign traffic that uses a particular Netfilter helper to a particular priority band: #BAND PROTO PORT(S) ADDRESS INTERFACE HELPER 1 - - - - sip In this example, SIP and associated RTP traffic will be assigned to priority band 1 (assuming that the nf_conntrack_sip helper is loaded). It is suggested that entries specifying an INTERFACE be placed the top of the file. That way, the band assigned to a particular packet will be the last entry matched by the packet. Packets which match no entry in shorewall-tcpri(5) are assigned to priority bands using their TOS field as previously described. One cause of high latency on interactive traffic can be that queues are building up at your ISP's gateway router. If you suspect that is happening in your case, you can try to eliminate the problem by using the IN-BANDWIDTH setting in shorewall-tcinterfaces(5). The contents of the column are a rate. For defining the rate, use kbit or kbps (for Kilobytes per second) and make sure there is NO space between the number and the unit (it is 100kbit not 100 kbit). mbit, mbps or a raw number (which means bytes) can be used, but note that only integer numbers are supported (0.5 is not valid). To pick an appropriate setting, we recommend that you start by setting IN-BANDWIDTH significantly below your measured download bandwidth (20% or so). While downloading, measure the ping response time from the firewall to the upstream router as you gradually increase the setting. The optimal setting is at the point beyond which the ping time increases sharply as you increase the setting. Simple Traffic Shaping is only appropriate on interfaces where output queuing occurs. As a consequence, you usually only use it on extermal interfaces. There are cases where you may need to use it on an internal interface (a VPN interface, for example). If so, just add an entry to shorewall-tcinterfaces(5): #INTERFACE TYPE IN-BANDWIDTH tun0 Internal

The PRIO(8) (tc-prio) manpage has additional information on the facility that Shorewall Simple Traffic Shaping is based on. Please note that Shorewall numbers the bands 1-3 whereas PRIO(8) refers to them as bands 0-2.