Tom Eastep 2005 Thomas M. Eastep Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover, and with no Back-Cover Texts. A copy of the license is included in the section entitled GNU Free Documentation License.

Ipsets are an extension to Netfilter/iptables that are currently available in Patch-O-Matic-ng (http://www.netfilter.org). Using ipsets requires that you patch your kernel and iptables and that you build and install the ipset utility from http://ipset.netfilter.org/. Ipset allows you to create one or more named sets of addresses then use those sets to define Netfilter/iptables rules. Possible uses of ipsets include: Blacklists. Ipsets provide an efficient way to represent large sets of addresses and you can maintain the lists without the need to restart or even refresh your Shorewall configuration. Zone definition. Using the /etc/shorewall/hosts file, you can define a zone based on the (dynamic) contents of an ipset. Again, you can then add or delete addresses to the ipset without restarting Shorewall. See the ipsets site (URL above) for additional information about ipsets.

Support for ipsets was introduced in Shorewall version 2.3.0. In most places where a host or network address may be used, you may also use the name of an ipset prefaced by "+". Example: "+Mirrors" When using Shorewall-perl, the names of ipsets are restricted as follows: They must begin with a letter (after the '+'). They must be composed of letters, digits or underscores ("_"). The name of the set may optionally followed by: a number from 1 to 6 enclosed in square brackets ([]) -- this number indicates the maximum number of ipset binding levels that are to be matched. Depending on the context where the ipset name is used, either all "src" or all "dst" matches will be used. Example: "+Mirrors[4]" a series of "src" and "dst" options separated by commas and enclosed in square brackets ([]). These will be passed directly to iptables in the generated --set clause. See the ipset documentation for details. Example: "+Mirrors[src,dst,src]" Note that "+Mirrors[4]" used in the SOURCE column of the rules file is equivalent to "+Mirrors[src,src,src,src]". To generate a negative match, prefix the "+" with "!" as in "!+Mirrors". Example 1: Blacklist all hosts in an ipset named "blacklist" /etc/shorewall/blacklist#ADDRESS/SUBNET PROTOCOL PORT +blacklist Example 2: Allow SSH from all hosts in an ipset named "sshok: /etc/shorewall/rules#ACTION SOURCE DEST PROTO DEST PORT(S) ACCEPT +sshok $FW tcp 22 Shorewall can automatically manage the contents of your ipsets for you. If you specify SAVE_IPSETS=Yes in /etc/shorewall/shorewall.conf then "shorewall save" will save the contents of your ipsets. The file where the sets are saved is formed by taking the name where the Shorewall configuration is stored and appending "-ipsets". So if you enter the command "shorewall save standard" then Shorewall will save the file as /var/lib/shorewall/standard-ipsets Regardless of the setting of SAVE_IPSETS, the shorewall -f start and shorewall restore commands will restore the ipset contents corresponding to the Shorewall configuration restored provided that the saved Shorewall configuration specified exists. For example, shorewall restore standard would restore the ipset contents from /var/lib/shorewall/standard-ipsets provided that /var/lib/shorewall/standard exists and is executable and that /var/lib/shorewall/standard-ipsets exists and is executable. Also regardless of the setting of SAVE_IPSETS, the shorewall forget command will purge the saved ipset information (if any) associated with the saved shorewall configuration being removed. You can also associate ipset contents with Shorewall configuration directories using the following command: ipset -S > <config directory>/ipsets Example: ipset -S > /etc/shorewall/ipsets When you start or restart Shorewall (including using the try command) from the configuration directory, your ipsets will be configured from the saved ipsets file. Once again, this behavior is independent of the setting of SAVE_IPSETS. As mentioned above, ipsets are well suited for large blacklists. You can maintain your blacklist using the 'ipset' utility without ever having to restart or refresh Shorewall. If you use the SAVE_IPSETS=Yes feature just be sure to "shorewall save" after altering the blacklist ipset(s). Example: /etc/shorewall/blacklist: #ADDRESS/SUBNET PROTOCOL PORT +Blacklist[src,dst] +Blacklistnets[src,dst] Create the blacklist ipsets using: ipset -N Blacklist iphash ipset -N Blacklistnets nethash Add entries: ipset -A Blacklist 206.124.146.177 ipset -A Blacklistnets 206.124.147.0/24 To allow entries for individual ports: ipset -N SMTP portmap --from 1 --to 31 ipset -A SMTP 25 ipset -A Blacklist 206.124.146.177 ipset -B Blacklist 206.124.146.177 -b SMTP Now only port 25 will be blocked from 206.124.146.177.

The use of ipsets provides a much better way to define dynamic zones than is provided by the native Shorewall implementation. To define a dynamic zone of hosts dyn that interface through interface eth3, use: /etc/shorewall/zones: #ZONE TYPE OPTIONS IN OPTIONS OUT OPTIONS dyn ipv4 /etc/shorewall/interfaces: #ZONE INTERFACE OPTIONS - eth3 … /etc/shorewall/hosts: #ZONE HOSTS OPTIONS dyn eth3:+Dyn Now create an ipmap named Dyn and you're all set. You can add and delete addresses from Dyn without having to touch Shorewall.