Tom Eastep Bill Shirley 2001 - 2016 Thomas M. Eastep Bill Shirley Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is included in the section entitled GNU Free Documentation License. This article applies to Shorewall 4.3 and later. If you are running a version of Shorewall earlier than Shorewall 4.3.5 then please see the documentation for that release.

The disposition of packets entering a Shorewall firewall is determined by one of a number of Shorewall facilities. Only some of these facilities permit logging. The packet is part of an established connection. While the packet can be logged using LOG rules in the ESTABLISHED section of /etc/shorewall/rules, that is not recommended because of the large amount of information that may be logged. The packet represents a connection request that is related to an established connection (such as a data connection associated with an FTP control connection). These packets may be logged using LOG rules in the RELATED section of /etc/shorewall/rules. The packet is rejected because of an option in /etc/shorewall/shorewall.conf or /etc/shorewall/interfaces. These packets can be logged by setting the appropriate logging-related option in /etc/shorewall/shorewall.conf. The packet matches a rule in /etc/shorewall/rules. By including a syslog level (see below) in the ACTION column of a rule (e.g., ACCEPT:info net $FW tcp 22), the connection attempt will be logged at that level. The packet doesn't match a rule so it is handled by a policy defined in /etc/shorewall/policy. These may be logged by specifying a syslog level in the LOG LEVEL column of the policy's entry (e.g., loc net ACCEPT info).

By default, Shorewall directs Netfilter to log using syslog (8). Syslog classifies log messages by a facility and a priority (using the notation facility.priority). The facilities defined by syslog are auth, authpriv, cron, daemon, kern, lpr, mail, mark, news, syslog, user, uucp and local0 through local7. Throughout the Shorewall documentation, I will use the term level rather than priority since level is the term used by Netfilter. The syslog documentation uses the term priority.

Syslog levels are a method of describing to syslog (8) the importance of a message. A number of Shorewall parameters have a syslog level as their value. Valid levels are: 7 - debug (Debug-level messages) 6 - info (Informational) 5 - notice (Normal but significant Condition) 4 - warning (Warning Condition) 3 - err (Error Condition) 2 - crit (Critical Conditions) 1 - alert (must be handled immediately) 0 - emerg (System is unusable) For most Shorewall logging, a level of 6 (info) is appropriate. Shorewall log messages are generated by Netfilter and are logged using the kern facility and the level that you specify. If you are unsure of the level to choose, 6 (info) is a safe bet. You may specify levels by name or by number. Beginning with Shorewall 4.5.5, the level name or number may be optionally followed by a comma-separated list of one or more log options. The list is enclosed in parentheses. Log options cause additional information to be included in each log message. Valid log options are: ip_options Log messages will include the option settings from the IP header. macdecode Decode the MAC address and protocol. tcp_sequence Include TCP sequence numbers. tcp_options Include options from the TCP header. uid Include the UID of the sending program; only valid for packets originating on the firewall itself. Example: info(tcp_options,tcp_sequence) Syslogd writes log messages to files (typically in /var/log/*) based on their facility and level. The mapping of these facility/level pairs to log files is done in /etc/syslog.conf (5). If you make changes to this file, you must restart syslogd before the changes can take effect. Syslog may also write to your system console. See Shorewall FAQ 16 for ways to avoid having Shorewall messages written to the console.

There are a couple of limitations to syslogd-based logging: If you give, for example, kern.info its own log destination then that destination will also receive all kernel messages of levels 5 (notice) through 0 (emerg). All kernel.info messages will go to that destination and not just those from Netfilter. If your kernel has NFLOG target support (and most vendor-supplied kernels do), you may also specify a log level of NFLOG (must be all caps). When NFLOG is used, Shorewall will direct Netfilter to log the related messages via the NFLOG target which will send them to a process called ulogd. The ulogd program is included in most distributions and is also available from http://www.netfilter.org/projects/ulogd/index.html. Ulogd can be configured to log all Shorewall messages to their own log file. The NFLOG logging mechanism is completely separate from syslog. Once you switch to NFLOG, the settings in /etc/syslog.conf have absolutely no effect on your Shorewall logging (except for Shorewall status messages which still go to syslog). You will need to change all instances of log levels (usually info) in your Shorewall configuration files to NFLOG - this includes entries in the policy, rules and shorewall.conf files. If you initially installed using Shorewall 5.1.2 or later, you can simply change the setting of LOG_LEVEL in shorewall.conf. Otherwise, you must search for all instances of log levels in your configuration and change them accordingly. If you currently run Shorewall 5.1.2 or later, then change them to $LOG_LEVEL and set LOG_LEVEL accordingly. If you are running an earlier release, using a shell variable simplifies future changes. Here's what I had at one time: gateway:/etc/shorewall# grep -v ^\# * | egrep '\$LOG|ULOG|LOGFILE' params:LOG=NFLOG policy:loc $FW REJECT $LOG policy:net all DROP $LOG 10/sec:40 policy:all all REJECT $LOG rules:REJECT:$LOG loc net tcp 25 rules:REJECT:$LOG loc net udp 1025:1031 rules:REJECT:$LOG dmz net udp 1025:1031 rules:ACCEPT:$LOG dmz net tcp 1024: 20 rules:REJECT:$LOG $FW net udp 1025:1031 shorewall.conf:LOGFILE=/var/log/shorewall shorewall.conf:LOGUNCLEAN=$LOG shorewall.conf:MACLIST_LOG_LEVEL=$LOG shorewall.conf:TCP_FLAGS_LOG_LEVEL=$LOG shorewall.conf:RFC1918_LOG_LEVEL=$LOG gateway:/etc/shorewall# Finally edit /etc/shorewall/shorewall.conf and set LOGFILE=<file that you wish to log to>. This tells the /sbin/shorewall program where to look for the log when processing its show log, logwatch and dump commands. The NFLOG target is a successor to ULOG. Both ULOG and NFLOG may be followed by a list of up to three numbers in parentheses. The first number specifies the netlink group (0-65535). If omitted (e.g., NFLOG(,0,10)) then a value of 0 is assumed. The second number specifies the maximum number of bytes to copy. If omitted, 0 (no limit) is assumed. The third number specifies the number of log messages that should be buffered in the kernel before they are sent to user space. The default is 1. Examples: /etc/shorewall/shorewall.conf: MACLIST_LOG_LEVEL=NFLOG(1,0,1) /etc/shorewall/rules:#ACTION SOURCE DEST PROTO DPORT ACCEPT:NFLOG(1,0,1) vpn fw tcp ssh,time,631,8080 Shorewall considers ULOG(...) and NFLOG(...) to be log levels, just like info, debug, etc. even though they are not defined by syslog. Here is a copy of a ulogd.conf file that logs to /var/log/firewall. It was contributed by a Shorewall user on IRC: [global] user="ulogd" logfile="/var/log/ulogd/ulogd.log" loglevel=7 plugin="/usr/lib64/ulogd/ulogd_inppkt_NFLOG.so" plugin="/usr/lib64/ulogd/ulogd_filter_IFINDEX.so" plugin="/usr/lib64/ulogd/ulogd_filter_IP2STR.so" plugin="/usr/lib64/ulogd/ulogd_filter_PRINTPKT.so" plugin="/usr/lib64/ulogd/ulogd_output_LOGEMU.so" plugin="/usr/lib64/ulogd/ulogd_raw2packet_BASE.so" stack=log:NFLOG,base1:BASE,ifi1:IFINDEX,ip2str1:IP2STR,print1:PRINTPKT,firewall:LOGEMU [firewall] file="/var/log/firewall" sync=1 This sample config file assumes that NFLOG is being used in logging rules and policies.

Netfilter logging allows configuration of multiple backends. Logging backends provide the The low-level forward of log messages. There are currently three backends: LOG (ipt_LOG and ip6t_LOG). Normal kernel-based logging to a syslog daemon. ULOG (ipt_ULOG) ULOG logging as described ablve. Only available for IPv4. netlink (nfnetlink_log) The logging backend behind NFLOG, defined above. The currently-available and currently-selected IPv4 and IPv6 backends are shown in /proc/sys/net/netfilter/nf_log: cat /proc/net/netfilter/nf_log 0 NONE (nfnetlink_log) 1 NONE (nfnetlink_log) 2 ipt_ULOG (ipt_ULOG,ipt_LOG,nfnetlink_log) 3 NONE (nfnetlink_log) 4 NONE (nfnetlink_log) 5 NONE (nfnetlink_log) 6 NONE (nfnetlink_log) 7 NONE (nfnetlink_log) 8 NONE (nfnetlink_log) 9 NONE (nfnetlink_log) 10 ip6t_LOG (ip6t_LOG,nfnetlink_log) 11 NONE (nfnetlink_log) 12 NONE (nfnetlink_log) The magic numbers (0-12) are Linux address family numbers (AF_INET is 2 and AF_INET6 is 10). The name immediately following the number is the currently-selected backend, and the ones in parantheses are the ones that are available. You can change the currently selected backend by echoing it's name into /proc/net/netfilter/nf_log.number. Example - change the IPv4 backend to LOG: sysctl net.netfilter.nf_log.2=ipt_LOG Beginning with Shorewall 4.6.4, you can configure the backend using the LOG_BACKEND option in shorewall.conf(5) and shorewall6.conf(5).

Here is a post describing configuring syslog-ng to work with Shorewall. Recent SUSE releases come preconfigured with syslog-ng with Netfilter messages (including Shorewall's) are written to /var/log/firewall.

For general information on the contents of Netfilter log messages, see http://logi.cc/en/2010/07/netfilter-log-format/. For Shorewall-specific information, see FAQ #17.

In addition to the options mentioned above, a certain amount of customization of the Netfilter-generated messages is allowed.

In a Shorewall logging rule, the log level can be followed by a log tag as in "DROP:NFLOG:junk". The generated log message will include "chain-name junk DROP".

By setting the LOGTAGONLY option to Yes in shorewall.conf(5) or shorewall6.conf(5), the disposition ('DROP' in the above example) will be omitted. Consider the following rule: #ACTION SOURCE DEST PROTO REJECT(icmp-proto-unreachable):notice:IPv6 loc net 41 # who's using IPv6 tunneling This rule generates the following warning at compile time: WARNING: Log Prefix shortened to "Shorewall:IPv6:REJECT(icmp-p " /etc/shorewall/rules (line 212) and produces the rather ugly prefix "Shorewall:IPv6:REJECT(icmp-p ". Now consider this similar rule: #ACTION SOURCE DEST PROTO REJECT(icmp-proto-unreachable):notice:IPv6,tunneling loc net 41 # who's using IPv6 tunneling With LOGTAGONLY=Yes, no warning is generated and the prefix becomes "Shorewall:IPv6:tunneling:" See the shorewall[6].conf man page for further information about how LOGTAGONLY=Yes can be used.

shorewall.conf(5) and shorewall6.conf(5) have a number of options whose values are log levels. Beginning with Shorewall 5.0.0, these specifcations may include a log tag as described above.

As a side note to the LOGTAGONLY example above, i recommend blocking all tunneling because it bypasses the firewall rules: #ACTION SOURCE DEST PROTO DPORT ?COMMENT tunneling REJECT(icmp-proto-unreachable):notice:IPv6,tunneling loc net 41 # who's using IPv6 tunneling REJECT(icmp-port-unreachable) loc net tcp,udp teredo REJECT(icmp-port-unreachable) loc net tcp,udp isakmp,ipsec-nat-t Here is an example of logging traffic only once: /etc/shorewall/init: ipset -exist create IPv4 hash:ip timeout 86400 ipset -exist create IPv4-port hash:ip,port timeout 14400 /etc/shorewall/rules (at the top): #ACTION SOURCE DEST PROTO ?SECTION NEW # ------------------ ?COMMENT drop previously flagged DROP net:+IPv4[src] fw DROP net:+IPv4-port[src,dst] fw After all the rules have been checked, at the bottom of /etc/shorewall/rules: # ============================================================================= # =============================== H@ck0rz ===================================== # ============================================================================= ?COMMENT dont whack myself REJECT:notice inet:$ME_NET fw ?COMMENT not public ADD(+IPv4-port:src,dst) net fw tcp,udp domain ADD(+IPv4-port:src,dst) net fw tcp ldap,ldaps ADD(+IPv4-port:src,dst) net fw tcp,udp ipp ?COMMENT H@ck0rz ADD(+IPv4:src) net fw tcp ssh ADD(+IPv4:src) net fw tcp ftp,ftps,sftp,telnet,telnets,exec,login,shell,sunrpc ADD(+IPv4:src) net fw tcp,udp ms-sql-s,ms-sql-m ?COMMENT drop if added DROP:info:BAN,IPv4 net:+IPv4[src] fw DROP:info:BAN,IPv4-port net:+IPv4-port[src,dst] fw One final note: I wanted less firewall messages in /var/log/messages so I added to rsyslog.conf: #### RULES #### <-- find this if $msg contains 'Shorewall' then { action(type="omfile" file="/var/log/shorewall.log") # if ($syslogfacility == 0 and $syslogseverity >= 4) then stop # warning # if ($syslogfacility == 0 and $syslogseverity >= 5) then stop # notice if ($syslogfacility == 0 and $syslogseverity >= 6) then stop # info } I log at 'notice' log level if I want the message in /var/log/messages and everything goes to /var/log/shorewall.log. Don't forget to add /var/log/shorewall.log to logrotate.