<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE article PUBLIC "-//OASIS//DTD DocBook XML V4.2//EN"
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd">
<article id="IPSEC">
<!--$Id$-->
<articleinfo>
<title>IPSEC using Linux Kernel 2.6</title>
<authorgroup>
<author>
<firstname>Tom</firstname>
<surname>Eastep</surname>
</author>
</authorgroup>
<pubdate>2005-09-30</pubdate>
<copyright>
<year>2004</year>
<year>2005</year>
<holder>Thomas M. Eastep</holder>
</copyright>
<legalnotice>
<para>Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU Free Documentation License, Version
1.2 or any later version published by the Free Software Foundation; with
no Invariant Sections, with no Front-Cover, and with no Back-Cover
Texts. A copy of the license is included in the section entitled
<quote><ulink url="GnuCopyright.htm">GNU Free Documentation
License</ulink></quote>.</para>
</legalnotice>
</articleinfo>
<caution>
<para><emphasis role="bold">This article applies to Shorewall 3.0 and
later. If you are running a version of Shorewall earlier than Shorewall
3.0.0 then please see the documentation for that
release.</emphasis></para>
</caution>
<important>
<para>The information in this article is only applicable if you plan to
have IPSEC end-points on the same system where Shorewall is used.</para>
</important>
<warning>
<para>To use the features described in this article, your kernel and
iptables must include the Netfilter+ipsec patches and policy match
support. The Netfilter patches are available from Netfilter
Patch-O-Matic-NG and are also included in some commercial distributions
(most notably <trademark>SUSE</trademark> 9.1 through 9.3).</para>
</warning>
<important>
<para>You must have <emphasis role="bold">BOTH</emphasis> the
Netfilter+ipsec patches and the policy match patch. <emphasis
role="bold">One without the other will not work</emphasis>.</para>
<para>Here's a combination of components that I know works:</para>
<orderedlist>
<listitem>
<para>Kernel 2.6.11 from kernel.org. Patched with:</para>
<itemizedlist>
<listitem>
<para>The five patches in <ulink
url="http://shorewall.net/pub/shorewall/contrib/IPSEC/2.6.11">http://shorewall.net/pub/shorewall/contrib/IPSEC/2.6.11</ulink></para>
</listitem>
<listitem>
<para>The "policy match" extension from the Patch-o-matic-ng CVS
snapshot from 2005-May-04 (be sure to NOT try to apply the
ipsec-NN patches from patch-o-matic-ng).</para>
</listitem>
</itemizedlist>
</listitem>
<listitem>
<para>iptables 1.3.1 patched with the "policy match" extension from
the Patch-o-matic-ng CVS snapshot from 2005-May-04.</para>
</listitem>
<listitem>
<para>ipsec-tools 0.5.2 compiled from source. I've also had success
with:</para>
<itemizedlist>
<listitem>
<para>ipsec-tools 0.5.2 and racoon 0.5.2 from Debian
Sarge/testing</para>
</listitem>
<listitem>
<para>The ipsec-tools 0.5 rpm from SUSE 9.3.</para>
</listitem>
</itemizedlist>
</listitem>
</orderedlist>
</important>
<warning>
<para>As of this writing, the Netfilter+ipsec and policy match support are
broken when used with a bridge device. The problem has been reported to
the responsible Netfilter developer who has confirmed the problem.</para>
</warning>
<section>
<title>Shorewall 3.0 and Kernel 2.6 IPSEC</title>
<para>This is <emphasis role="bold">not</emphasis> a HOWTO for Kernel 2.6
IPSEC -- for that, please see <ulink
url="http://www.ipsec-howto.org/">http://www.ipsec-howto.org/</ulink>.</para>
<para>The 2.6 Linux Kernel introduces new facilities for defining
encrypted communication between hosts in a network. The network
administrator defines a set of <firstterm>Security Policies</firstterm>
which are stored in the kernel as a <firstterm>Security Policy
Database</firstterm> (SPD). Security policies determine which traffic is
subject to encryption. <firstterm>Security Associations</firstterm> are
created between pairs of hosts in the network (one SA for traffic in each
direction); these SAs define how traffic is to be encrypted. Outgoing
traffic that is to be encrypted according to the contents of the SPD
requires an appropriate SA to exist. SAs may be created manually using
<command>setkey</command>(8) but most often, they are created by a
cooperative process involving the ISAKMP protocol and daemons such
as<command> racoon</command> or <command>isakmpd</command>. Incoming
traffic is verified against the SPD to ensure that no unencrypted traffic
is accepted in violation of the administrator's policies.</para>
<para>There are three ways in which IPSEC traffic can interact with
Shorewall policies and rules:</para>
<orderedlist>
<listitem>
<para>Traffic that is encrypted on the firewall system. The traffic
passes through Netfilter twice -- first as unencrypted then
encrypted.</para>
</listitem>
<listitem>
<para>Traffic that is decrypted on the firewall system. The traffic
passes through Netfilter twice -- first as encrypted then as
unencrypted.</para>
</listitem>
<listitem>
<para>Encrypted traffic that is passed through the firewall system.
The traffic passes through Netfilter once.</para>
</listitem>
</orderedlist>
<para>In cases 1 and 2, the encrypted traffic is handled by entries in
<filename>/etc/shorewall/tunnels</filename> (don't be mislead by the name
of the file -- <emphasis>transport mode</emphasis> encrypted traffic is
also handled by entries in that file). The unencrypted traffic is handled
by normal rules and policies.</para>
<para>Under the 2.4 Linux Kernel, the association of unencrypted traffic
and zones was made easy by the presense of IPSEC pseudo-interfaces with
names of the form <filename class="devicefile">ipsecn</filename> (e.g.
<filename class="devicefile">ipsec0</filename>). Outgoing unencrypted
traffic (case 1.) was send through an <filename
class="devicefile">ipsecn</filename> device while incoming unencrypted
traffic (case 2) arrived from an <filename
class="devicefile">ipsecn</filename> device. The 2.6 kernel-based
implementation does away with these pseudo-interfaces. Outgoing traffic
that is going to be encrypted and incoming traffic that has been decrypted
must be matched against policies in the SPD and/or the appropriate
SA.</para>
<para>Shorewall provides support for policy matching in three ways:</para>
<orderedlist>
<listitem>
<para>In <filename>/etc/shorewall/masq</filename>, traffic that will
later be encrypted is exempted from MASQUERADE/SNAT using existing
entries. If you want to MASQUERADE/SNAT outgoing traffic that will
later be encrypted, you must include the appropriate indication in the
new IPSEC column in that file.</para>
</listitem>
<listitem>
<para>The<filename> </filename><ulink
url="Documentation.htm#Zones"><filename>/etc/shorewall/zones</filename></ulink>
file allows you to associate zones with traffic that will be encrypted
or that has been decrypted.</para>
</listitem>
<listitem>
<para>A new option (<emphasis role="bold">ipsec</emphasis>) has been
provided for entries in <filename>/etc/shorewall/hosts</filename>.
When an entry has this option specified, traffic to/from the hosts
described in the entry is assumed to be encrypted.</para>
</listitem>
</orderedlist>
<para>In summary, Shorewall provides the facilities to replace the use of
ipsec pseudo-interfaces in zone and MASQUERADE/SNAT definition.</para>
<para>There are two cases to consider:</para>
<orderedlist>
<listitem>
<para>Encrypted communication is used to/from all hosts in a
zone.</para>
<para>The value <emphasis role="bold">ipsec</emphasis> is placed in
the TYPE column of the <filename>/etc/shorewall/zones</filename> entry
for the zone.</para>
</listitem>
<listitem>
<para>By default, encrypted communication is not used to communicate
with the hosts in a zone.</para>
<para>The value <emphasis role="bold">ipv4</emphasis> is placed in the
TYPE column of the <filename>/etc/shorewall/zones</filename> entry for
the zone and the new <emphasis role="bold">ipsec</emphasis> option is
specified in <filename>/etc/shorewall/hosts</filename> for any hosts
requiring secure communication.</para>
</listitem>
</orderedlist>
<note>
<para>For simple zones such as are shown in the following examples, the
two techniques are equivalent and are used interchangably.</para>
</note>
<note>
<para>It is redundent to have <emphasis role="bold">ipsec</emphasis> in
the TYPE column of the <filename>/etc/shorewall/zones</filename> entry
for a zone and to also have the <emphasis role="bold">ipsec</emphasis>
option in <filename>/etc/shorewall/hosts</filename> entries for that
zone.</para>
</note>
<para>Finally, the OPTIONS, IN OPTIONS and OUT OPTIONS columns in
/etc/shorewall/zones can be used to match the zone to a particular (set
of) SA(s) used to encrypt and decrypt traffic to/from the zone and the
security policies that select which traffic to encrypt/decrypt.</para>
<para>This article assumes the use of ipsec-tools (<ulink
url="http://ipsec-tools.sourceforge.net">http://ipsec-tools.sourceforge.net</ulink>).
As of this writing, I recommend that you run at least version 0.5.2.
Debian users, please note that there are separate Debian packages for
ipsec-tools and racoon although the ipsec-tools project releases them as a
single package.</para>
<para>For more information on IPSEC, Kernel 2.6 and Shorewall see <ulink
url="LinuxFest.pdf">my presentation on the subject given at LinuxFest NW
2005</ulink>. Be warned though that the presentation is based on Shorewall
2.2 and there are some differences in the details of how IPSEC is
configured.</para>
</section>
<section>
<title>IPSec Gateway on the Firewall System</title>
<para>Suppose that we have the following sutuation:</para>
<graphic fileref="images/TwoNets1.png" />
<para>We want systems in the 192.168.1.0/24 sub-network to be able to
communicate with systems in the 10.0.0.0/8 network. We assume that on both
systems A and B, eth0 is the internet interface.</para>
<para>To make this work, we need to do two things:</para>
<orderedlist numeration="loweralpha">
<listitem>
<para>Open the firewall so that the IPSEC tunnel can be established
(allow the ESP and AH protocols and UDP Port 500).</para>
</listitem>
<listitem>
<para>Allow traffic through the tunnel.</para>
</listitem>
</orderedlist>
<para>Opening the firewall for the IPSEC tunnel is accomplished by adding
an entry to the <filename>/etc/shorewall/tunnels</filename> file.</para>
<para>In <filename>/etc/shorewall/tunnels</filename> on system A, we need
the following</para>
<blockquote>
<para><filename>/etc/shorewall/tunnels</filename> — System A:</para>
<programlisting>#TYPE ZONE GATEWAY GATEWAY ZONE
ipsec net 134.28.54.2
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
<para><filename>/etc/shorewall/tunnels</filename> — System B:</para>
<programlisting>#TYPE ZONE GATEWAY GATEWAY ZONE
ipsec net 206.162.148.9
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<note>
<para>If either of the endpoints is behind a NAT gateway then the
tunnels file entry on the <emphasis role="bold">other</emphasis>
endpoint should specify a tunnel type of ipsecnat rather than ipsec and
the GATEWAY address should specify the external address of the NAT
gateway.</para>
</note>
<para>You need to define a zone for the remote subnet or include it in
your local zone. In this example, we'll assume that you have created a
zone called <quote>vpn</quote> to represent the remote subnet.</para>
<blockquote>
<para><filename>/etc/shorewall/zones</filename> — Systems A and
B:</para>
<programlisting>#ZONE TYPE OPTIONS IN OUT
# OPTIONS OPTIONS
vpn ipv4
net ipv4
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<para>Remember the assumption that both systems A and B have eth0 as their
internet interface.</para>
<para>You must define the vpn zone using the
<filename>/etc/shorewall/hosts</filename> file. The hosts file entries
below assume that you want the remote gateway to be part of the vpn zone —
If you don't wish the remote gateway included, simply omit it's IP address
from the HOSTS column.</para>
<blockquote>
<para>/etc/shorewall/hosts — System A</para>
<programlisting>#ZONE HOSTS OPTIONS
vpn eth0:10.0.0.0/8,134.28.54.2 <emphasis role="bold"> ipsec</emphasis>
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
<para>/etc/shorewall/hosts — System B</para>
<programlisting>#ZONE HOSTS OPTIONS
vpn eth0:192.168.1.0/24,206.162.148.9 <emphasis role="bold">ipsec</emphasis>
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<para>Assuming that you want to give each local network free access to the
remote network and vice versa, you would need the following
<filename>/etc/shorewall/policy</filename> entries on each system:</para>
<blockquote>
<programlisting>#SOURCE DESTINATION POLICY LEVEL BURST:LIMIT
loc vpn ACCEPT
vpn loc ACCEPT</programlisting>
</blockquote>
<para>Once you have these entries in place, restart Shorewall (type
shorewall restart); you are now ready to configure IPSEC.</para>
<para>For full encrypted connectivity in this configuration (between the
subnets, between each subnet and the opposite gateway, and between the
gateways), you will need eight policies in
<filename>/etc/racoon/setkey.conf</filename>. For example, on gateway
A:</para>
<blockquote>
<programlisting># First of all flush the SPD and SAD databases
spdflush;
flush;
# Add some SPD rules
spdadd 192.168.1.0/24 10.0.0.0/8 any -P out ipsec esp/tunnel/206.162.148.9-134.28.54.2/require;
spdadd 192.168.1.0/24 134.28.54.2/32 any -P out ipsec esp/tunnel/206.162.148.9-134.28.54.2/require;
spdadd 206.162.148.9/32 134.28.54.2/32 any -P out ipsec esp/tunnel/206.162.148.9-134.28.54.2/require;
spdadd 206.162.148.9/32 10.0.0.0/8 any -P out ipsec esp/tunnel/206.162.148.9-134.28.54.2/require;
spdadd 10.0.0.0/8 192.168.1.0/24 any -P in ipsec esp/tunnel/134.28.54.2-206.162.148.9/require;
spdadd 10.0.0.0/8 206.162.148.9/32 any -P in ipsec esp/tunnel/134.28.54.2-206.162.148.9/require;
spdadd 134.28.54.2/32 192.168.1.0/24 any -P in ipsec esp/tunnel/134.28.54.2-206.162.148.9/require;
spdadd 134.28.54.2/32 206.162.148.9/32 any -P in ipsec esp/tunnel/134.28.54.2-206.162.148.9/require;</programlisting>
</blockquote>
<para>The <filename>setkey.conf</filename> file on gateway B would be
similar.</para>
<para>A sample <filename>/etc/racoon/racoon.conf</filename> file using
X.509 certificates might look like:</para>
<blockquote>
<programlisting>path certificates "/etc/certs" ;
listen
{
isakmp 206.162.148.9;
}
remote 134.28.54.2
{
exchange_mode main ;
certificate_type x509 "GatewayA.pem" "GatewayA_key.pem" ;
verify_cert on;
my_identifier asn1dn ;
peers_identifier asn1dn ;
verify_identifier on ;
lifetime time 24 hour ;
proposal {
encryption_algorithm blowfish;
hash_algorithm sha1;
authentication_method rsasig ;
dh_group 2 ;
}
}
sainfo address 192.168.1.0/24 any address 10.0.0.0/8 any
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}
sainfo address 206.162.148.9/32 any address 10.0.0.0/8 any
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}
sainfo address 206.162.148.9/32 any address 134.28.54.2/32 any
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}
sainfo address 192.168.1.0/24 any address 134.28.54.2/32 any
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}</programlisting>
<warning>
<para>If you have hosts that access the internet through an IPSEC
tunnel, then it is a good idea to set the MSS value for traffic from
those hosts explicitly in the
<filename>/etc/shorewall/zones</filename> file. For example, if hosts
in the <emphasis role="bold">sec</emphasis> zone access the internet
through an ESP tunnel then the following entry would be
appropriate:</para>
<programlisting>#ZONE TYPE OPTIONS IN OUT
# OPTIONS OPTIONS
sec ipsec mode=tunnel <emphasis role="bold">mss=1400</emphasis></programlisting>
<para>Note that CLAMPMSS=Yes in <filename>shorewall.conf</filename>
isn't effective with the 2.6 native IPSEC implementation because there
is no separate ipsec device with a lower mtu as there was under the
2.4 and earlier kernels.</para>
</warning>
</blockquote>
</section>
<section>
<title>Mobile System (Road Warrior)</title>
<para>Suppose that you have a laptop system (B) that you take with you
when you travel and you want to be able to establish a secure connection
back to your local network.</para>
<graphic fileref="images/Mobile.png" />
<example>
<title>Road Warrior VPN</title>
<para>You need to define a zone for the laptop or include it in your
local zone. In this example, we'll assume that you have created a zone
called <quote>vpn</quote> to represent the remote host.</para>
<blockquote>
<para>/etc/shorewall/zones — System A</para>
<programlisting>#ZONE TYPE OPTIONS IN OUT
# OPTIONS OPTIONS
vpn ipsec
net ipv4
loc ipv4
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<para>In this instance, the mobile system (B) has IP address 134.28.54.2
but that cannot be determined in advance. In the
<filename>/etc/shorewall/tunnels</filename> file on system A, the
following entry should be made:<blockquote>
<programlisting>#TYPE ZONE GATEWAY GATEWAY ZONE
ipsec net 0.0.0.0/0 vpn
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote></para>
<para><note>
<para>the GATEWAY ZONE column contains the name of the zone
corresponding to peer subnetworks. This indicates that the gateway
system itself comprises the peer subnetwork; in other words, the
remote gateway is a standalone system.</para>
</note></para>
<para>The VPN zone is defined using the /etc/shorewall/hosts
file:</para>
<blockquote>
<para>/etc/shorewall/hosts — System A:</para>
<programlisting>#ZONE HOSTS OPTIONS
vpn eth0:0.0.0.0/0
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<para>You will need to configure your <quote>through the tunnel</quote>
policy as shown under the first example above.</para>
<para>On the laptop:</para>
<blockquote>
<para>/etc/shorewall/zones - System B:</para>
<programlisting>#ZONE TYPE OPTIONS IN OUT
# OPTIONS OPTIONS
vpn ipsec
net ipv4
loc ipv4
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
<para>/etc/shorewall/tunnels - System B:</para>
<programlisting>#TYPE ZONE GATEWAY GATEWAY ZONE
ipsec net 206.162.148.9 vpn
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
<para>/etc/shorewall/hosts - System B:</para>
<programlisting>#ZONE HOSTS OPTIONS
vpn eth0:0.0.0.0/0
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
</blockquote>
<para>On system A, here are the IPSEC files:</para>
<blockquote>
<para>/etc/racoon/racoon.conf - System A:</para>
<programlisting>path certificate "/etc/certs" ;
listen
{
isakmp 206.162.148.9;
}
remote <emphasis role="bold">anonymous</emphasis>
{
exchange_mode main ;
<emphasis role="bold">generate_policy on</emphasis> ;
<emphasis role="bold">passive on</emphasis> ;
certificate_type x509 "GatewayA.pem" "GatewayA_key.pem" ;
verify_cert on;
my_identifier asn1dn ;
peers_identifier asn1dn ;
verify_identifier on ;
lifetime time 24 hour ;
proposal {
encryption_algorithm blowfish ;
hash_algorithm sha1;
authentication_method rsasig ;
dh_group 2 ;
}
}
sainfo <emphasis role="bold">anonymous</emphasis>
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}</programlisting>
<para>/etc/racoon/setkey.conf - System A:</para>
<programlisting>flush;
spdflush;</programlisting>
</blockquote>
<para>If system A is running kernel 2.6.10 or later then it must also be
running ipsec-tools (racoon) 0.5rc1 or later.</para>
<para>On the mobile system (system B), it is not possible to create a
static IPSEC configuration because the IP address of the laptop's
internet connection isn't static. I have created an 'ipsecvpn' script
and included in the tarball and in the RPM's documentation directory;
this script can be used to start and stop the connection.</para>
<para>The ipsecvpn script has some variable assignments at the top -- in
the above case, these would be as follows:</para>
<blockquote>
<programlisting>#
# External Interface
#
INTERFACE=eth0
#
# Remote IPSEC Gateway
#
GATEWAY=206.162.148.9
#
# Networks behind the remote gateway
#
NETWORKS="192.168.1.0/24"
#
# Directory where X.509 certificates are stored.
#
CERTS=/etc/certs
#
# Certificate to be used for this connection. The cert
# directory must contain:
#
# ${CERT}.pem - the certificate
# ${CERT}_key.pem - the certificates's key
#
CERT=roadwarrior
#
# The setkey binary
#
SETKEY=/usr/sbin/setkey
#
# The racoon binary
#
RACOON=/usr/sbin/racoon</programlisting>
</blockquote>
<para>The ipsecvpn script can be installed in /etc/init.d/ but it is
probably best installed in /usr/local/sbin and run manually:</para>
<blockquote>
<para><command>ipsecvpn start </command># Starts the tunnel</para>
<para><command>ipsecvpn stop</command> # Stops the tunnel</para>
</blockquote>
</example>
<warning>
<para>Although the ipsecvpn script allows you to specify multiple remote
NETWORKS as a space-separated list, SAs are created on the gateway only
during ISAKMP negotiation. So in practice, only the first remote network
accessed will be accessible from the roadwarrior.</para>
</warning>
</section>
<section>
<title>Transport Mode</title>
<para>In today's wireless world, it is often the case that individual
hosts in a network need to establish secure connections with the other
hosts in that network. In that case, IPSEC transport mode is an
appropriate solution.</para>
<para><graphic fileref="images/TransportMode.png" />Here's an example
using the ipsec-tools package. The files shown are from host
192.168.20.10; the configuration of the other nodes is similar.</para>
<blockquote>
<para><filename>/etc/racoon/racoon.conf</filename>:</para>
<programlisting>path pre_shared_key "/etc/racoon/psk.txt" ;
remote anonymous
{
exchange_mode main ;
my_identifier address ;
lifetime time 24 hour ;
proposal {
encryption_algorithm blowfish ;
hash_algorithm sha1;
authentication_method pre_shared_key ;
dh_group 2 ;
}
}
sainfo anonymous
{
pfs_group 2;
lifetime time 12 hour ;
encryption_algorithm blowfish ;
authentication_algorithm hmac_sha1, hmac_md5 ;
compression_algorithm deflate ;
}
</programlisting>
<para><filename>/etc/racoon/setkey.conf</filename>:</para>
<programlisting># First of all flush the SPD database
spdflush;
# Add some SPD rules
spdadd 192.168.20.10/32 192.168.20.20/32 any -P out ipsec esp/transport/192.168.20.10-192.168.20.20/require;
spdadd 192.168.20.20/32 192.168.20.10/32 any -P in ipsec esp/transport/192.168.20.20-192.168.20.10/require;
spdadd 192.168.20.10/32 192.168.20.30/32 any -P out ipsec esp/transport/192.168.20.10-192.168.20.30/require;
spdadd 192.168.20.30/32 192.168.20.10/32 any -P in ipsec esp/transport/192.168.20.30-192.168.20.10/require;
spdadd 192.168.20.10/32 192.168.20.40/32 any -P out ipsec esp/transport/192.168.20.10-192.168.20.40/require;
spdadd 192.168.20.40/32 192.168.20.10/32 any -P in ipsec esp/transport/192.168.20.40-192.168.20.10/require;
</programlisting>
<para>/etc/racoon/psk.txt:</para>
<programlisting>192.168.20.20 <key for 192.168.20.10<->192.168.20.20>
192.168.20.30 <key for 192.168.20.10<->192.168.20.30>
192.168.20.40 <key for 192.168.20.10<->192.168.20.40></programlisting>
<para>Note that the <emphasis role="bold">same key</emphasis>must be
used in both directions.</para>
</blockquote>
<para>Shorewall configuration goes as follows:</para>
<blockquote>
<para><filename>/etc/shorewall/interfaces</filename>:</para>
<programlisting>#ZONE INTERFACE BROADCAST OPTIONS
net eth0 detect routefilter,dhcp,tcpflags
#LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE</programlisting>
<para>/etc/shorewall/tunnels:</para>
<programlisting>#TYPE ZONE GATEWAY GATEWAY
# ZONE
ipsec:noah net 192.168.20.0/24 loc</programlisting>
<para>/etc/shorewall/zones:</para>
<programlisting>#ZONE TYPE OPTIONS IN OUT
# OPTIONS OPTIONS
loc ipsec mode=transport
net ipv4</programlisting>
<para><filename>/etc/shorewall/hosts</filename>:</para>
<programlisting>#ZONE HOST(S) OPTIONS
loc eth0:192.168.20.0/24
#LAST LINE -- ADD YOUR ENTRIES BEFORE THIS LINE -- DO NOT REMOVE</programlisting>
<para>It is worth noting that although <emphasis>loc</emphasis> is a
sub-zone of <emphasis>net</emphasis>, because <emphasis>loc</emphasis>
is an IPSEC-only zone it does not need to be defined before
<emphasis>net</emphasis> in
<emphasis>/etc/shorewall/zones</emphasis>.</para>
<para><filename>/etc/shorewall/policy</filename>:</para>
<programlisting>#SOURCE DEST POLICY LOG LEVEL LIMIT:BURST
$FW all ACCEPT
loc $FW ACCEPT
net loc NONE
loc net NONE
net all DROP info
# The FOLLOWING POLICY MUST BE LAST
all all REJECT info
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE</programlisting>
<para>Since there are no cases where net<->loc traffic should
occur, NONE policies are used.</para>
</blockquote>
</section>
<section>
<title>IPSEC and <trademark>Windows</trademark> XP</title>
<para>I have successfully configured my work laptop to use IPSEC with
X.509 certificates for wireless IP communication when it is undocked at
home. I looked at dozens of sites and the one I found most helpful was
<ulink
url="http://ipsec.math.ucla.edu/services/ipsec-windows.html">http://ipsec.math.ucla.edu/services/ipsec-windows.html</ulink>.
The instructions on that site are directed to students at UCLA but they
worked fine for me (once I followed them very carefully).</para>
<warning>
<para>The instructions found on the UCLA site are complex and do not
include any information on the generation of X.509 certificates. There
are lots of sites however that can tell you how to generate
certificates, including <ulink
url="http://www.ipsec-howto.org/">http://www.ipsec-howto.org/</ulink>.</para>
<para>One piece of information that may not be so easy to find is "How
do I generate a PKCS#12 certificate to import into Windows?". Here's the
openssl command that I used:</para>
<programlisting><command>openssl pkcs12 -export -in eastepnc6000.pem -inkey eastepnc6000_key.pem -out eastepnc6000.pfx -name "IPSEC Cert for Home Wireless"</command> </programlisting>
<para>I was prompted for a password to associate with the certificate.
This password is entered on the Windows system during import.</para>
<para>In the above command:</para>
<itemizedlist>
<listitem>
<para><filename>eastepnc6000.pem</filename> was the laptop's
certificate in PEM format.</para>
</listitem>
<listitem>
<para><filename>eastepnc6000_key.pem</filename> was the laptop's
private key (actually, it's the original signing request which
includes the private key).</para>
</listitem>
<listitem>
<para><filename>eastepnc6000.pfx</filename> is the PKCS#12 output
file.</para>
</listitem>
<listitem>
<para>"IPSEC Cert for Home Wireless" is the friendly name for the
certificate.</para>
</listitem>
</itemizedlist>
<para>I started to write an article about how to do this, complete with
graphics captured from my laptop. I gave up. I had captured 12 images
and hadn't really started yet. The Windows interface for configuring
IPSEC is the worst GUI that I have ever used. What can be displayed on
one split Emacs screen (racoon.conf plus setkey.conf) takes 20+
different dialog boxes on Windows XP!!!</para>
</warning>
</section>
<section>
<title>Source of Additional Samples</title>
<para>Be sure to check out the <filename
class="directory">src/racoon/samples</filename> subdirectory in the
ipsec-tools source tree. It has a wide variety of sample racoon
configuration files.</para>
</section>
</article>