mirror of
https://gitlab.com/shorewall/code.git
synced 2024-12-25 07:38:57 +01:00
12c0c5b40c
git-svn-id: https://shorewall.svn.sourceforge.net/svnroot/shorewall/trunk@2986 fbd18981-670d-0410-9b5c-8dc0c1a9a2bb
992 lines
45 KiB
XML
Executable File
992 lines
45 KiB
XML
Executable File
<?xml version="1.0" encoding="UTF-8"?>
|
|
<!DOCTYPE article PUBLIC "-//OASIS//DTD DocBook XML V4.2//EN"
|
|
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd">
|
|
<article id="three-interface">
|
|
<!--$Id$-->
|
|
|
|
<articleinfo>
|
|
<title>Three-Interface Firewall</title>
|
|
|
|
<authorgroup>
|
|
<author>
|
|
<firstname>Tom</firstname>
|
|
|
|
<surname>Eastep</surname>
|
|
</author>
|
|
</authorgroup>
|
|
|
|
<pubdate>2005-11-10</pubdate>
|
|
|
|
<copyright>
|
|
<year>2002-2005</year>
|
|
|
|
<holder>Thomas M. Eastep</holder>
|
|
</copyright>
|
|
|
|
<legalnotice>
|
|
<para>Permission is granted to copy, distribute and/or modify this
|
|
document under the terms of the GNU Free Documentation License, Version
|
|
1.2 or any later version published by the Free Software Foundation; with
|
|
no Invariant Sections, with no Front-Cover, and with no Back-Cover
|
|
Texts. A copy of the license is included in the section entitled
|
|
<quote><ulink url="GnuCopyright.htm">GNU Free Documentation
|
|
License</ulink></quote>.</para>
|
|
</legalnotice>
|
|
</articleinfo>
|
|
|
|
<caution>
|
|
<para><emphasis role="bold">This article applies to Shorewall 3.0 and
|
|
later. If you are running a version of Shorewall earlier than Shorewall
|
|
3.0.0 then please see the documentation for that
|
|
release.</emphasis></para>
|
|
</caution>
|
|
|
|
<section>
|
|
<title>Introduction</title>
|
|
|
|
<para>Setting up a Linux system as a firewall for a small network with DMZ
|
|
is a fairly straight-forward task if you understand the basics and follow
|
|
the documentation.</para>
|
|
|
|
<para>This guide doesn't attempt to acquaint you with all of the features
|
|
of Shorewall. It rather focuses on what is required to configure Shorewall
|
|
in one of its more popular configurations:</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para>Linux system used as a firewall/router for a small local
|
|
network.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Single public IP address.</para>
|
|
|
|
<note>
|
|
<para>If you have more than one public IP address, this is not the
|
|
guide you want -- see the <ulink
|
|
url="shorewall_setup_guide.htm">Shorewall Setup Guide</ulink>
|
|
instead.</para>
|
|
</note>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>DMZ connected to a separate ethernet interface. The purpose of a
|
|
DMZ is to isolate those servers that are exposed to the Internet from
|
|
your local systems so that if one of those servers is compromised
|
|
there is still a firewall between the hacked server and your local
|
|
systems.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Connection through DSL, Cable Modem, ISDN, Frame Relay, dial-up,
|
|
...</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
|
|
<para>Here is a schematic of a typical installation.</para>
|
|
|
|
<figure>
|
|
<title>schematic of a typical installation</title>
|
|
|
|
<mediaobject>
|
|
<imageobject>
|
|
<imagedata align="center" fileref="images/dmz1.png" format="PNG" />
|
|
</imageobject>
|
|
</mediaobject>
|
|
</figure>
|
|
|
|
<section>
|
|
<title>Requirements</title>
|
|
|
|
<para>Shorewall requires that you have the
|
|
<command>iproute</command>/<command>iproute2</command> package installed
|
|
(on <trademark>RedHat</trademark>, the package is called
|
|
<command>iproute</command>). You can tell if this package is installed
|
|
by the presence of an <command>ip</command> program on your firewall
|
|
system. As <systemitem class="username">root</systemitem>, you can use
|
|
the <command>which</command> command to check for this program:</para>
|
|
|
|
<programlisting>[root@gateway root]# <command>which ip</command>
|
|
/sbin/ip
|
|
[root@gateway root]#</programlisting>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Before you start</title>
|
|
|
|
<para>I recommend that you first read through the guide to familiarize
|
|
yourself with what's involved then go back through it again making your
|
|
configuration changes.</para>
|
|
|
|
<caution>
|
|
<para>If you edit your configuration files on a
|
|
<trademark>Windows</trademark> system, you must save them as
|
|
<trademark>Unix</trademark> files if your editor supports that option
|
|
or you must run them through <command>dos2unix</command> before trying
|
|
to use them. Similarly, if you copy a configuration file from your
|
|
<trademark>Windows</trademark> hard drive to a floppy disk, you must
|
|
run <command>dos2unix</command> against the copy before using it with
|
|
Shorewall.</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para><ulink url="http://www.simtel.net/pub/pd/51438.html">Windows
|
|
Version of dos2unix</ulink></para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><ulink
|
|
url="http://www.megaloman.com/%7Ehany/software/hd2u/">Linux
|
|
Version of dos2unix</ulink></para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
</caution>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Conventions</title>
|
|
|
|
<para>Points at which configuration changes are recommended are flagged
|
|
with <inlinegraphic fileref="images/BD21298_.gif"
|
|
format="GIF" />.</para>
|
|
|
|
<para>Configuration notes that are unique to LEAF/Bering are marked with
|
|
<inlinegraphic fileref="images/leaflogo.gif" format="GIF" />.</para>
|
|
</section>
|
|
</section>
|
|
|
|
<section>
|
|
<title>PPTP/ADSL</title>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>If you have an ADSL Modem and you use PPTP to communicate with a
|
|
server in that modem, you must make the <ulink
|
|
url="PPTP.htm#PPTP_ADSL">changes recommended here</ulink> in addition to
|
|
those detailed below. ADSL with PPTP is most commonly found in Europe,
|
|
notably in Austria.</para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Shorewall Concepts</title>
|
|
|
|
<para>The configuration files for Shorewall are contained in the directory
|
|
<filename>/etc/shorewall</filename> -- for simple setups, you will only
|
|
need to deal with a few of these as described in this guide.<warning>
|
|
<para><emphasis role="bold">Note to Debian Users</emphasis></para>
|
|
|
|
<para>If you install using the .deb, you will find that your <filename
|
|
class="directory">/etc/shorewall</filename> directory is empty. This
|
|
is intentional. The released configuration file skeletons may be found
|
|
on your system in the directory <filename
|
|
class="directory">/usr/share/doc/shorewall/default-config</filename>.
|
|
Simply copy the files you need from that directory to <filename
|
|
class="directory">/etc/shorewall</filename> and modify the
|
|
copies.</para>
|
|
|
|
<para>Note that you must copy <filename
|
|
class="directory">/usr/share/doc/shorewall/default-config/shorewall.conf</filename>
|
|
and /usr/share/doc/shorewall/default-config/modules to /etc/shorewall
|
|
even if you do not modify those files.</para>
|
|
</warning></para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>After you have installed Shorewall, locate the three-interface
|
|
Sample configuration:</para>
|
|
|
|
<orderedlist>
|
|
<listitem>
|
|
<para>If you installed using an RPM, the samples will be in the
|
|
Samples/three-interfaces/ subdirectory of the Shorewall documentation
|
|
directory. If you don't know where the Shorewall documentation
|
|
directory is, you can find the samples using this command:</para>
|
|
|
|
<programlisting>~# rpm -ql shorewall | fgrep three-interfaces
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/interfaces
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/masq
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/policy
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/routestopped
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/rules
|
|
/usr/share/doc/packages/shorewall/Samples/three-interfaces/zones
|
|
~#</programlisting>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If you installed using the tarball, the samples are in the
|
|
Samples/three-interfaces directory in the tarball.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If you installed using the .deb, the samples are in
|
|
/usr/share/doc/shorewall/examples/three-interfaces.</para>
|
|
</listitem>
|
|
</orderedlist>
|
|
|
|
<para>As each file is introduced, I suggest that you look through the
|
|
actual file on your system -- each file contains detailed configuration
|
|
instructions and default entries.</para>
|
|
|
|
<para>Shorewall views the network where it is running as being composed of
|
|
a set of zones. In the three-interface sample configuration, the following
|
|
zone names are used:</para>
|
|
|
|
<para><programlisting>#ZONE TYPE OPTIONS IN OUT
|
|
# OPTIONS OPTIONS
|
|
fw firewall
|
|
net ipv4
|
|
loc ipv4
|
|
dmz ipv4</programlisting>Zone names are defined in
|
|
<filename>/etc/shorewall/zones</filename>.</para>
|
|
|
|
<para>Note that Shorewall recognizes the firewall system as its own zone.
|
|
When the /etc/shorewall/zones file is processed, he name of the firewall
|
|
zone is stored in the shell variable <firstterm>$FW</firstterm> which may
|
|
be used throughout the Shorewall configuration to refer to the firewall
|
|
zone.</para>
|
|
|
|
<para>Rules about what traffic to allow and what traffic to deny are
|
|
expressed in terms of zones.</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para>You express your default policy for connections from one zone to
|
|
another zone in the <filename>/etc/shorewall/policy</filename>
|
|
file.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>You define exceptions to those default policies in the
|
|
<filename>/etc/shorewall/rules</filename> file.</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
|
|
<para>For each connection request entering the firewall, the request is
|
|
first checked against the <filename>/etc/shorewall/rules</filename> file.
|
|
If no rule in that file matches the connection request then the first
|
|
policy in <filename>/etc/shorewall/policy</filename> that matches the
|
|
request is applied. If there is a <ulink
|
|
url="shorewall_extension_scripts.htm">comon action</ulink> defined for the
|
|
policy in <filename>/etc/shorewall/actions</filename> or
|
|
<filename>/usr/share/shorewall/actions.std</filename> then that action is
|
|
peformed before the action is applied.</para>
|
|
|
|
<para>The <filename>/etc/shorewall/policy</filename> file included with
|
|
the three-interface sample has the following policies:</para>
|
|
|
|
<programlisting>#SOURCE DEST POLICY LOG LEVEL LIMIT:BURST
|
|
loc net ACCEPT
|
|
net all DROP info
|
|
all all REJECT info</programlisting>
|
|
|
|
<important>
|
|
<para>In the three-interface sample, the line below is included but
|
|
commented out. If you want your firewall system to have full access to
|
|
servers on the internet, uncomment that line.</para>
|
|
|
|
<programlisting>#SOURCE DEST POLICY LOG LEVEL LIMIT:BURST
|
|
$FW net ACCEPT</programlisting>
|
|
</important>
|
|
|
|
<para>The above policy will:</para>
|
|
|
|
<orderedlist>
|
|
<listitem>
|
|
<para>allow all connection requests from your local network to the
|
|
internet</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>drop (ignore) all connection requests from the internet to your
|
|
firewall or local network</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>optionally accept all connection requests from the firewall to
|
|
the internet (if you uncomment the additional policy)</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>reject all other connection requests.</para>
|
|
</listitem>
|
|
</orderedlist>
|
|
|
|
<para>It is important to note that Shorewall policies (and rules) refer to
|
|
<emphasis role="bold">connections</emphasis> and not packet flow. With the
|
|
policies defined in the <filename
|
|
class="directory">/etc/shorewall/policy</filename> file shown above,
|
|
connections are allowed from the <emphasis>loc</emphasis> zone to the
|
|
<emphasis>net</emphasis> zone even though connections are not allowed from
|
|
the <emphasis>loc</emphasis> zone to the firewall itself.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>At this point, edit your <filename>/etc/shorewall/policy</filename>
|
|
file and make any changes that you wish.</para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Network Interfaces</title>
|
|
|
|
<figure>
|
|
<title>DMZ</title>
|
|
|
|
<mediaobject>
|
|
<imageobject>
|
|
<imagedata align="center" fileref="images/dmz1.png" format="PNG" />
|
|
</imageobject>
|
|
</mediaobject>
|
|
</figure>
|
|
|
|
<para>The firewall has three network interfaces. Where Internet
|
|
connectivity is through a cable or DSL <quote>Modem</quote>, the External
|
|
Interface will be the ethernet adapter that is connected to that
|
|
<quote>Modem</quote> (e.g., <filename class="devicefile">eth0</filename>)
|
|
unless you connect via <emphasis>Point-to-Point Protocol</emphasis> over
|
|
Ethernet (PPPoE) or <emphasis>Point-to-Point Tunneling Protocol</emphasis>
|
|
(PPTP) in which case the External Interface will be a
|
|
<literal>ppp</literal> interface (e.g., <filename
|
|
class="devicefile">ppp0</filename>). If you connect via a regular modem,
|
|
your External Interface will also be <filename
|
|
class="devicefile">ppp0</filename>. If you connect using ISDN, you
|
|
external interface will be <filename
|
|
class="devicefile">ippp0</filename>.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>I<emphasis role="bold">f your external interface is <filename
|
|
class="devicefile">ppp0</filename> or <filename
|
|
class="devicefile">ippp0</filename> then you will want to set
|
|
<varname>CLAMPMSS=yes</varname> in
|
|
<filename>/etc/shorewall/shorewall.conf</filename>.</emphasis></para>
|
|
|
|
<para>Your Local Interface will be an ethernet adapter (<filename
|
|
class="devicefile">eth0</filename>, <filename
|
|
class="devicefile">eth1</filename> or <filename
|
|
class="devicefile">eth2</filename>) and will be connected to a hub or
|
|
switch. Your local computers will be connected to the same switch (note:
|
|
If you have only a single local system, you can connect the firewall
|
|
directly to the computer using a cross-over cable).</para>
|
|
|
|
<para>Your DMZ Interface will also be an ethernet adapter (<filename
|
|
class="devicefile">eth0</filename>, <filename
|
|
class="devicefile">eth1</filename> or <filename
|
|
class="devicefile">eth2</filename>) and will be connected to a hub or
|
|
switch. Your DMZ computers will be connected to the same switch (note: If
|
|
you have only a single DMZ system, you can connect the firewall directly
|
|
to the computer using a cross-over cable).</para>
|
|
|
|
<caution>
|
|
<para><emphasis role="bold">Do NOT connect the internal and external
|
|
interface to the same hub or switch except for testing</emphasis>. You
|
|
can test using this kind of configuration if you specify the arp_filter
|
|
option in <filename>/etc/shorewall/interfaces</filename> for all
|
|
interfaces connected to the common hub/switch. <emphasis
|
|
role="bold">Using such a setup with a production firewall is strongly
|
|
recommended against</emphasis>.</para>
|
|
</caution>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>The Shorewall three-interface sample configuration assumes that the
|
|
external interface is <filename class="devicefile">eth0</filename>, the
|
|
local interface is <filename class="devicefile">eth1</filename> and the
|
|
DMZ interface is <filename class="devicefile">eth2</filename>. If your
|
|
configuration is different, you will have to modify the sample
|
|
<filename>/etc/shorewall/interfaces</filename> file accordingly. While you
|
|
are there, you may wish to review the list of options that are specified
|
|
for the interfaces. Some hints:</para>
|
|
|
|
<tip>
|
|
<para>If your external interface is <filename
|
|
class="devicefile">ppp0</filename> or <filename
|
|
class="devicefile">ippp0</filename>, you can replace the
|
|
<quote>detect</quote> in the second column with <quote>-</quote>
|
|
(without the quotes).</para>
|
|
</tip>
|
|
|
|
<tip>
|
|
<para>If your external interface is <filename
|
|
class="devicefile">ppp0</filename> or <filename
|
|
class="devicefile">ippp0</filename> or if you have a static IP address,
|
|
you can remove <quote>dhcp</quote> from the option list.</para>
|
|
</tip>
|
|
</section>
|
|
|
|
<section>
|
|
<title>IP Addresses</title>
|
|
|
|
<para>Before going further, we should say a few words about Internet
|
|
Protocol (IP) addresses. Normally, your ISP will assign you a single
|
|
Public IP address. This address may be assigned via the Dynamic Host
|
|
Configuration Protocol (DHCP) or as part of establishing your connection
|
|
when you dial in (standard modem) or establish your PPP connection. In
|
|
rare cases, your ISP may assign you a static IP address; that means that
|
|
you configure your firewall's external interface to use that address
|
|
permanently. Regardless of how the address is assigned, it will be shared
|
|
by all of your systems when you access the Internet. You will have to
|
|
assign your own addresses for your internal network (the local and DMZ
|
|
Interfaces on your firewall plus your other computers). RFC 1918 reserves
|
|
several Private IP address ranges for this purpose:</para>
|
|
|
|
<programlisting>10.0.0.0 - 10.255.255.255
|
|
172.16.0.0 - 172.31.255.255
|
|
192.168.0.0 - 192.168.255.255</programlisting>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>Before starting Shorewall, <emphasis role="bold">you should look at
|
|
the IP address of your external interface and if it is one of the above
|
|
ranges, you should remove the <varname>norfc1918</varname> option from the
|
|
external interface's entry in
|
|
<filename>/etc/shorewall/interfaces</filename>.</emphasis></para>
|
|
|
|
<para>You will want to assign your local addresses from one sub-network or
|
|
subnet and your DMZ addresses from another subnet. For our purposes, we
|
|
can consider a subnet to consists of a range of addresses <systemitem
|
|
class="ipaddress">x.y.z.0</systemitem> - <systemitem
|
|
class="ipaddress">x.y.z.255</systemitem>. Such a subnet will have a Subnet
|
|
Mask of <systemitem class="netmask">255.255.255.0</systemitem>. The
|
|
address <systemitem class="ipaddress">x.y.z.0</systemitem> is reserved as
|
|
the Subnet Address and <systemitem class="netmask">x.y.z.255</systemitem>
|
|
is reserved as the Subnet Broadcast Address. In Shorewall, a subnet is
|
|
described using Classless InterDomain Routing (CIDR) notation with
|
|
consists of the subnet address followed by <varname>/24</varname>. The
|
|
<varname>24</varname> refers to the number of consecutive <quote>1</quote>
|
|
bits from the left of the subnet mask.</para>
|
|
|
|
<table>
|
|
<title>Example sub-network</title>
|
|
|
|
<tgroup cols="2">
|
|
<colspec align="left" />
|
|
|
|
<tbody>
|
|
<row>
|
|
<entry>Range:</entry>
|
|
|
|
<entry><systemitem class="ipaddress">10.10.10.0</systemitem> -
|
|
<systemitem class="ipaddress">10.10.10.255</systemitem></entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>Subnet Address:</entry>
|
|
|
|
<entry><systemitem
|
|
class="ipaddress">10.10.10.0</systemitem></entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>Broadcast Address:</entry>
|
|
|
|
<entry><systemitem
|
|
class="ipaddress">10.10.10.255</systemitem></entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>CIDR Notation:</entry>
|
|
|
|
<entry><systemitem
|
|
class="ipaddress">10.10.10.0/24</systemitem></entry>
|
|
</row>
|
|
</tbody>
|
|
</tgroup>
|
|
</table>
|
|
|
|
<para>It is conventional to assign the internal interface either the first
|
|
usable address in the subnet (<systemitem
|
|
class="ipaddress">10.10.10.1</systemitem> in the above example) or the
|
|
last usable address (<systemitem
|
|
class="ipaddress">10.10.10.254</systemitem>).</para>
|
|
|
|
<para>One of the purposes of subnetting is to allow all computers in the
|
|
subnet to understand which other computers can be communicated with
|
|
directly. To communicate with systems outside of the subnetwork, systems
|
|
send packets through a gateway (router).</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>Your local computers (Local Computers 1 & 2) should be
|
|
configured with their default gateway set to the IP address of the
|
|
firewall's internal interface and your DMZ computers (DMZ Computers 1
|
|
& 2) should be configured with their default gateway set to the IP
|
|
address of the firewall's DMZ interface.</para>
|
|
|
|
<para>The foregoing short discussion barely scratches the surface
|
|
regarding subnetting and routing. If you are interested in learning more
|
|
about IP addressing and routing, I highly recommend <quote>IP
|
|
Fundamentals: What Everyone Needs to Know about Addressing &
|
|
Routing</quote>, Thomas A. Maufer, Prentice-Hall, 1999, ISBN
|
|
0-13-975483-0.</para>
|
|
|
|
<para>The remainder of this quide will assume that you have configured
|
|
your network as shown here:</para>
|
|
|
|
<figure>
|
|
<title>DMZ</title>
|
|
|
|
<mediaobject>
|
|
<imageobject>
|
|
<imagedata fileref="images/dmz2.png" />
|
|
</imageobject>
|
|
|
|
<caption>
|
|
<para>The default gateway for the DMZ computers would be <systemitem
|
|
class="ipaddress">10.10.11.254</systemitem> and the default gateway
|
|
for the Local computers would be <systemitem
|
|
class="ipaddress">10.10.10.254</systemitem>.</para>
|
|
|
|
<warning>
|
|
<para>Your ISP might assign your external interface an RFC 1918
|
|
address. If that address is in the <systemitem
|
|
class="ipaddress">10.10.10.0/24</systemitem> subnet then you will
|
|
need to select a DIFFERENT RFC 1918 subnet for your local network
|
|
and if it is in the <systemitem
|
|
class="ipaddress">10.10.11.0/24</systemitem> subnet then you will
|
|
need to select a different RFC 1918 subnet for your DMZ.</para>
|
|
</warning>
|
|
</caption>
|
|
</mediaobject>
|
|
</figure>
|
|
</section>
|
|
|
|
<section>
|
|
<title>IP Masquerading (SNAT)</title>
|
|
|
|
<para>The addresses reserved by RFC 1918 are sometimes referred to as
|
|
non-routable because the Internet backbone routers don't forward packets
|
|
which have an RFC-1918 destination address. When one of your local systems
|
|
(let's assume local computer 1) sends a connection request to an internet
|
|
host, the firewall must perform Network Address Translation (NAT). The
|
|
firewall rewrites the source address in the packet to be the address of
|
|
the firewall's external interface; in other words, the firewall makes it
|
|
look as if the firewall itself is initiating the connection. This is
|
|
necessary so that the destination host will be able to route return
|
|
packets back to the firewall (remember that packets whose destination
|
|
address is reserved by RFC 1918 can't be routed accross the internet).
|
|
When the firewall receives a return packet, it rewrites the destination
|
|
address back to 10.10.10.1 and forwards the packet on to local computer
|
|
1.</para>
|
|
|
|
<para>On Linux systems, the above process is often referred to as IP
|
|
Masquerading and you will also see the term Source Network Address
|
|
Translation (SNAT) used. Shorewall follows the convention used with
|
|
Netfilter: <itemizedlist>
|
|
<listitem>
|
|
<para><emphasis>Masquerade</emphasis> describes the case where you
|
|
let your firewall system automatically detect the external interface
|
|
address.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><emphasis>SNAT</emphasis> refers to the case when you
|
|
explicitly specify the source address that you want outbound packets
|
|
from your local network to use.</para>
|
|
</listitem>
|
|
</itemizedlist> In Shorewall, both Masquerading and SNAT are configured
|
|
with entries in the <filename
|
|
class="directory">/etc/shorewall/</filename><filename>masq</filename>
|
|
file.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>If your external firewall interface is <filename
|
|
class="devicefile">eth0</filename>, your local interface <filename
|
|
class="devicefile">eth1</filename> and your DMZ interface is <filename
|
|
class="devicefile">eth2</filename> then you do not need to modify the file
|
|
provided with the sample. Otherwise, edit <filename
|
|
class="directory">/etc/shorewall/</filename><filename>masq</filename> and
|
|
change it to match your configuration.</para>
|
|
|
|
<para>If, in spite of all advice to the contrary, you are using this guide
|
|
and want to use one-to-one NAT or Proxy ARP for your DMZ, remove the entry
|
|
for eth2 from <filename>/etc/shorewall/masq</filename>.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>If your external IP is static, you can enter it in the third column
|
|
in the <filename
|
|
class="directory">/etc/shorewall/</filename><filename>masq</filename>
|
|
entry if you like although your firewall will work fine if you leave that
|
|
column empty. Entering your static IP in column 3 makes processing
|
|
outgoing packets a little more efficient.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para><emphasis role="bold">If you are using the Debian package, please
|
|
check your <filename>shorewall.conf</filename> file to ensure that the
|
|
following is set correctly; if it is not, change it appropriately:
|
|
</emphasis><itemizedlist>
|
|
<listitem>
|
|
<para><varname>IP_FORWARDING=On</varname></para>
|
|
</listitem>
|
|
</itemizedlist></para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Port Forwarding (DNAT)</title>
|
|
|
|
<para>One of your goals will be to run one or more servers on your DMZ
|
|
computers. Because these computers have RFC-1918 addresses, it is not
|
|
possible for clients on the Internet to connect directly to them. It is
|
|
rather necessary for those clients to address their connection requests to
|
|
your firewall who rewrites the destination address to the address of your
|
|
server and forwards the packet to that server. When your server responds,
|
|
the firewall automatically performs SNAT to rewrite the source address in
|
|
the response.</para>
|
|
|
|
<para>The above process is called <emphasis>Port Forwarding</emphasis> or
|
|
<emphasis>Destination Network Address Translation</emphasis> (DNAT). You
|
|
configure port forwarding using DNAT rules in the <filename
|
|
class="directory">/etc/shorewall/</filename><filename>rules</filename>
|
|
file.</para>
|
|
|
|
<para>The general form of a simple port forwarding rule in <filename
|
|
class="directory">/etc/shorewall/</filename><filename>rules</filename> is:
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
DNAT net dmz:<emphasis><server local IP address></emphasis>[:<emphasis><server port></emphasis>] <emphasis><protocol></emphasis> <emphasis><port></emphasis></programlisting>
|
|
If you don't specify the <emphasis><varname><server
|
|
port></varname></emphasis>, it is assumed to be the same as
|
|
<emphasis><varname><port></varname></emphasis>.</para>
|
|
|
|
<example>
|
|
<title>You run a Web Server on DMZ Computer 2 and you want to forward
|
|
incoming TCP port 80 to that system</title>
|
|
|
|
<para><programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
Web/DNAT net dmz:10.10.11.2
|
|
Web/ACCEPT loc dmz:10.10.11.2</programlisting><itemizedlist>
|
|
<listitem>
|
|
<para>Entry 1 forwards port 80 from the Internet.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Entry 2 allows connections from the local network.</para>
|
|
</listitem>
|
|
</itemizedlist> Several important points to keep in mind:<itemizedlist>
|
|
<listitem>
|
|
<para>When you are connecting to your server from your local
|
|
systems, you must use the server's internal IP address
|
|
(<systemitem class="ipaddress">10.10.11.2</systemitem>).</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Many ISPs block incoming connection requests to port 80. If
|
|
you have problems connecting to your web server, try the following
|
|
rule and try connecting to port 5000 (e.g., connect to
|
|
<literal>http://w.x.y.z:5000 where w.x.y.z</literal> is your
|
|
external IP).<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S) SOURCE
|
|
# PORT(S)
|
|
DNAT net dmz:10.10.11.2:80 tcp 80 5000</programlisting></para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If you want to be able to access your server from the local
|
|
network using your external address, then if you have a static
|
|
external IP you can replace the loc->dmz rule above
|
|
with:<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S) SOURCE ORIGINAL
|
|
# PORT(S) DEST
|
|
DNAT loc dmz:10.10.11.2 tcp 80 - <emphasis><external IP></emphasis></programlisting>If
|
|
you have a dynamic IP then you must ensure that your external
|
|
interface is up before starting Shorewall and you must take steps
|
|
as follows (assume that your external interface is <filename
|
|
class="devicefile">eth0</filename>):<orderedlist>
|
|
<listitem>
|
|
<para>Include the following in /etc/shorewall/params:</para>
|
|
|
|
<para><command>ETH0_IP=$(find_interface_address
|
|
eth0)</command></para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Make your <literal>loc->dmz</literal> rule:
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S) SOURCE ORIGINAL
|
|
# PORT(S) DEST
|
|
DNAT loc dmz:10.10.11.2 tcp 80 - $ETH0_IP</programlisting></para>
|
|
</listitem>
|
|
</orderedlist></para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If you want to access your server from the DMZ using your
|
|
external IP address, see <ulink url="FAQ.htm#faq2a">FAQ
|
|
2a</ulink>.</para>
|
|
</listitem>
|
|
</itemizedlist></para>
|
|
</example>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>At this point, add the DNAT and ACCEPT rules for your
|
|
servers.</para>
|
|
|
|
<important>
|
|
<para>When testing DNAT rules like those shown above, you must test from
|
|
a client OUTSIDE YOUR FIREWALL (in the 'net' zone). You cannot test
|
|
these rules from inside the firewall!</para>
|
|
|
|
<para>For DNAT troubleshooting tips, <ulink url="FAQ.htm#faq1a">see FAQs
|
|
1a and 1b</ulink>.</para>
|
|
</important>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Domain Name Server (DNS)</title>
|
|
|
|
<para>Normally, when you connect to your ISP, as part of getting an IP
|
|
address your firewall's <emphasis>Domain Name Service</emphasis> (DNS)
|
|
resolver will be automatically configured (e.g., the
|
|
<filename>/etc/resolv.conf</filename> file will be written).
|
|
Alternatively, your ISP may have given you the IP address of a pair of DNS
|
|
name servers for you to manually configure as your primary and secondary
|
|
name servers. It is your responsibility to configure the resolver in your
|
|
internal systems. You can take one of two approaches: <itemizedlist>
|
|
<listitem>
|
|
<para>You can configure your internal systems to use your ISP's name
|
|
servers. If your ISP gave you the addresses of their servers or if
|
|
those addresses are available on their web site, you can configure
|
|
your internal systems to use those addresses. If that information
|
|
isn't available, look in <filename>/etc/resolv.conf</filename> on
|
|
your firewall system -- the name servers are given in
|
|
<quote>nameserver</quote> records in that file.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><inlinegraphic fileref="images/BD21298_.gif"
|
|
format="GIF" /></para>
|
|
|
|
<para>You can configure a <emphasis>Caching Name Server</emphasis>
|
|
on your firewall or in your DMZ. <trademark>Red Hat</trademark> has
|
|
an RPM for a caching name server (which also requires the
|
|
'<command>bind</command>' RPM) and for Bering users, there is
|
|
<filename>dnscache.lrp</filename>. If you take this approach, you
|
|
configure your internal systems to use the caching name server as
|
|
their primary (and only) name server. You use the internal IP
|
|
address of the firewall (<systemitem
|
|
class="ipaddress">10.10.10.254</systemitem> in the example above)
|
|
for the name server address if you choose to run the name server on
|
|
your firewall. To allow your local systems to talk to your caching
|
|
name server, you must open port 53 (both UDP and TCP) from the local
|
|
network to the server; you do that by adding the rules in
|
|
<filename>/etc/shorewall/rules</filename>.</para>
|
|
</listitem>
|
|
</itemizedlist> If you run the name server on the firewall:
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
DNS/ACCEPT loc $FW
|
|
DNS/ACCEPT dmz $FW </programlisting> Run name server on DMZ
|
|
computer 1: <programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
DNS/ACCEPT loc dmz:10.10.11.1
|
|
DNS/ACCEPT $FW dmz:10.10.11.1 </programlisting></para>
|
|
|
|
<para>In the rules shown above, <quote>DNS/ACCEPT</quote> is an example of
|
|
a <emphasis>defined macro</emphasis>. Shorewall includes a number of
|
|
defined macros and <ulink url="Macros.html">you can add your own</ulink>.
|
|
To see the list of macros included with your version of Shorewall, run the
|
|
command <command>ls
|
|
<filename>/usr/share/shorewall/macro.*</filename></command>.</para>
|
|
|
|
<para>You don't have to use defined macros when coding a rule in
|
|
<filename>/etc/shorewall/rules</filename>. The first example above (name
|
|
server on the firewall) could also have been coded as follows:</para>
|
|
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
ACCEPT loc $FW tcp 53
|
|
ACCEPT loc $FW udp 53
|
|
ACCEPT dmz $FW tcp 53
|
|
ACCEPT dmz $FW udp 53 </programlisting>
|
|
|
|
<para>In cases where Shorewall doesn't include a defined macro to meet
|
|
your needs, you can either define the macro yourself or you can simply
|
|
code the appropriate rules directly. <ulink url="ports.html">This
|
|
page</ulink> can be of help if you don't know the protocol and port
|
|
involved.</para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Other Connections</title>
|
|
|
|
<para>The three-interface sample includes the following rule:
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
DNS/ACCEPT $FW net </programlisting>That rule allow DNS access
|
|
from your firewall and may be removed if you commented out the line in
|
|
<filename>/etc/shorewall/policy</filename> allowing all connections from
|
|
the firewall to the Internet.</para>
|
|
|
|
<para>The sample also includes: <programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
SSH/ACCEPT loc $FW
|
|
SSH/ACCEPT loc dmz </programlisting>Those rules allow you to run
|
|
an SSH server on your firewall and in each of your DMZ systems and to
|
|
connect to those servers from your local systems.</para>
|
|
|
|
<para>If you wish to enable other connections between your systems, the
|
|
general format for using a defined macro is: <programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
<<emphasis>macro</emphasis>>/ACCEPT <emphasis><source zone> <destination zone></emphasis></programlisting></para>
|
|
|
|
<para>The general format when not using a defined action
|
|
is:<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
ACCEPT <emphasis><source zone> <destination zone> <protocol> <port> </emphasis></programlisting></para>
|
|
|
|
<example>
|
|
<title>You want to run a publicly-available DNS server on your firewall
|
|
system</title>
|
|
|
|
<para>Using defined macros:</para>
|
|
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
DNS/ACCEPT net $FW</programlisting>
|
|
|
|
<para>Not using defined actions:</para>
|
|
|
|
<programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
ACCEPT net $FW tcp 53
|
|
ACCEPT net $FW udp 53 </programlisting>
|
|
|
|
<para>Those rules would of course be in addition to the rules listed
|
|
above under "If you run the name server on your firewall".</para>
|
|
</example>
|
|
|
|
<para>If you don't know what port and protocol a particular application
|
|
uses, <ulink url="ports.htm">look here</ulink>.</para>
|
|
|
|
<important>
|
|
<para>I don't recommend enabling telnet to/from the Internet because it
|
|
uses clear text (even for login!). If you want shell access to your
|
|
firewall from the Internet, use SSH: <programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
SSH/ACCEPT net $FW</programlisting></para>
|
|
</important>
|
|
|
|
<para><inlinegraphic fileref="images/leaflogo.gif" format="GIF" /> Bering
|
|
users will want to add the following two rules to be compatible with
|
|
Jacques's Shorewall configuration: <programlisting>#ACTION SOURCE DEST PROTO DEST PORT(S)
|
|
ACCEPT loc $FW udp 53
|
|
ACCEPT net $FW tcp 80 </programlisting><itemizedlist>
|
|
<listitem>
|
|
<para>Entry 1 allows the DNS Cache to be used.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Entry 2 allows the <quote>weblet</quote> to work.</para>
|
|
</listitem>
|
|
</itemizedlist><inlinegraphic fileref="images/BD21298_.gif"
|
|
format="GIF" /></para>
|
|
|
|
<para>Now modify <filename>/etc/shorewall/rules</filename> to add or
|
|
remove other connections as required.</para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Some Things to Keep in Mind</title>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para><emphasis role="bold">You cannot test your firewall from the
|
|
inside</emphasis>. Just because you send requests to your firewall
|
|
external IP address does not mean that the request will be associated
|
|
with the external interface or the <quote>net</quote> zone. Any
|
|
traffic that you generate from the local network will be associated
|
|
with your local interface and will be treated as loc->fw
|
|
traffic.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><emphasis role="bold">IP addresses are properties of systems,
|
|
not of interfaces</emphasis>. It is a mistake to believe that your
|
|
firewall is able to forward packets just because you can ping the IP
|
|
address of all of the firewall's interfaces from the local network.
|
|
The only conclusion you can draw from such pinging success is that the
|
|
link between the local system and the firewall works and that you
|
|
probably have the local system's default gateway set correctly.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><emphasis role="bold">All IP addresses configured on firewall
|
|
interfaces are in the $FW (fw) zone</emphasis>. If 192.168.1.254 is
|
|
the IP address of your internal interface then you can write
|
|
<quote><emphasis role="bold">$FW:192.168.1.254</emphasis></quote> in a
|
|
rule but you may not write <quote><emphasis
|
|
role="bold">loc:192.168.1.254</emphasis></quote>. Similarly, it is
|
|
nonsensical to add 192.168.1.254 to the <emphasis
|
|
role="bold">loc</emphasis> zone using an entry in
|
|
<filename>/etc/shorewall/hosts</filename>.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><emphasis role="bold">Reply packets do NOT automatically follow
|
|
the reverse path of the one taken by the original request</emphasis>.
|
|
All packets are routed according to the routing table of the host at
|
|
each step of the way. This issue commonly comes up when people install
|
|
a Shorewall firewall parallel to an existing gateway and try to use
|
|
DNAT through Shorewall without changing the default gateway of the
|
|
system receiving the forwarded requests. Requests come in through the
|
|
Shorewall firewall where the destination IP address gets rewritten but
|
|
replies go out unmodified through the old gateway.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><emphasis role="bold">Shorewall itself has no notion of inside
|
|
or outside</emphasis>. These concepts are embodied in how Shorewall is
|
|
configured.</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Starting and Stopping Your Firewall</title>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>The <ulink url="Install.htm">installation procedure</ulink>
|
|
configures your system to start Shorewall at system boot but startup is
|
|
disabled so that your system won't try to start Shorewall before
|
|
configuration is complete. Once you have completed configuration of your
|
|
firewall, you can enable Shorewall startup by removing the file
|
|
<filename>/etc/shorewall/startup_disabled</filename>. <important>
|
|
<para>Users of the <filename>.deb</filename> package must edit
|
|
<filename>/etc/default/shorewall</filename> and set
|
|
<varname>startup=1</varname>.</para>
|
|
</important><important>
|
|
<para>You should edit
|
|
<filename>/etc/shorewall/shorewall.conf</filename> and set
|
|
STARTUP_ENABLED=Yes.</para>
|
|
</important>The firewall is started using the <command>shorewall
|
|
start</command> command and stopped using <command>shorewall
|
|
stop</command>. When the firewall is stopped, routing is enabled on those
|
|
hosts that have an entry in <ulink
|
|
url="Documentation.htm#Routestopped"><filename>/etc/shorewall/routestopped</filename></ulink>.
|
|
A running firewall may be restarted using the <command>shorewall
|
|
restart</command> command. If you want to totally remove any trace of
|
|
Shorewall from your Netfilter configuration, use <command>shorewall
|
|
clear</command>.</para>
|
|
|
|
<para><inlinegraphic fileref="images/BD21298_.gif" format="GIF" /></para>
|
|
|
|
<para>The three-interface sample assumes that you want to enable routing
|
|
to/from <filename class="devicefile">eth1</filename> (your local network)
|
|
and <filename class="devicefile">eth2</filename> (DMZ) when Shorewall is
|
|
stopped. If these two interfaces don't connect to your local network and
|
|
DMZ or if you want to enable a different set of hosts, modify
|
|
<filename>/etc/shorewall/routestopped</filename> accordingly. <warning>
|
|
<para>If you are connected to your firewall from the Internet, do not
|
|
issue a <command>shorewall stop</command> command unless you have
|
|
added an entry for the IP address that you are connected from to
|
|
<ulink
|
|
url="Documentation.htm#Routestopped"><filename>/etc/shorewall/routestopped</filename></ulink>.
|
|
Also, I don't recommend using <command>shorewall restart</command>; it
|
|
is better to create an <ulink
|
|
url="configuration_file_basics.htm#Levels">alternate
|
|
configuration</ulink> and test it using the <ulink
|
|
url="starting_and_stopping_shorewall.htm"><command>shorewall
|
|
try</command> command</ulink>.</para>
|
|
</warning></para>
|
|
</section>
|
|
|
|
<section>
|
|
<title>Additional Recommended Reading</title>
|
|
|
|
<para>I highly recommend that you review the <ulink
|
|
url="configuration_file_basics.htm">Common Configuration File
|
|
Features</ulink> page -- it contains helpful tips about Shorewall features
|
|
than make administering your firewall easier.</para>
|
|
</section>
|
|
</article> |