mirror of
https://gitlab.com/shorewall/code.git
synced 2024-11-14 03:34:31 +01:00
a3557759b0
git-svn-id: https://shorewall.svn.sourceforge.net/svnroot/shorewall/trunk@1299 fbd18981-670d-0410-9b5c-8dc0c1a9a2bb
100 lines
3.3 KiB
Plaintext
Executable File
100 lines
3.3 KiB
Plaintext
Executable File
#
|
|
# Shorewall 2.0 - Masquerade file
|
|
#
|
|
# /etc/shorewall/masq
|
|
#
|
|
# Use this file to define dynamic NAT (Masquerading) and to define Source NAT
|
|
# (SNAT).
|
|
#
|
|
# Columns are:
|
|
#
|
|
# INTERFACE -- Outgoing interface. This is usually your internet
|
|
# interface. If ADD_SNAT_ALIASES=Yes in
|
|
# /etc/shorewall/shorewall.conf, you may add ":" and
|
|
# a digit to indicate that you want the alias added with
|
|
# that name (e.g., eth0:0). This will allow the alias to
|
|
# be displayed with ifconfig. THAT IS THE ONLY USE FOR
|
|
# THE ALIAS NAME AND IT MAY NOT APPEAR IN ANY OTHER
|
|
# PLACE IN YOUR SHOREWALL CONFIGURATION.
|
|
#
|
|
# This may be qualified by adding the character
|
|
# ":" followed by a destination host or subnet.
|
|
#
|
|
#
|
|
# SUBNET -- Subnet that you wish to masquerade. You can specify this as
|
|
# a subnet or as an interface. If you give the name of an
|
|
# interface, you must have iproute installed and the interface
|
|
# must be up before you start the firewall.
|
|
#
|
|
# In order to exclude a subset of the specified SUBNET, you
|
|
# may append "!" and a comma-separated list of IP addresses
|
|
# and/or subnets that you wish to exclude.
|
|
#
|
|
# Example: eth1!192.168.1.4,192.168.32.0/27
|
|
#
|
|
# In that example traffic from eth1 would be masqueraded unless
|
|
# it came from 192.168.1.4 or 196.168.32.0/27
|
|
#
|
|
# ADDRESS -- (Optional). If you specify an address here, SNAT will be
|
|
# used and this will be the source address. If
|
|
# ADD_SNAT_ALIASES is set to Yes or yes in
|
|
# /etc/shorewall/shorewall.conf then Shorewall
|
|
# will automatically add this address to the
|
|
# INTERFACE named in the first column.
|
|
#
|
|
# You may also specify a range of up to 256
|
|
# IP addresses if you want the SNAT address to
|
|
# be assigned from that range in a round-robin
|
|
# range by connection. The range is specified by
|
|
# <first ip in range>-<last ip in range>.
|
|
#
|
|
# Example: 206.124.146.177-206.124.146.180
|
|
#
|
|
# Finally, you may also specify a comma-separated
|
|
# list of ranges and/or addresses in this column.
|
|
#
|
|
# This column may not contain DNS Names.
|
|
#
|
|
# Example 1:
|
|
#
|
|
# You have a simple masquerading setup where eth0 connects to
|
|
# a DSL or cable modem and eth1 connects to your local network
|
|
# with subnet 192.168.0.0/24.
|
|
#
|
|
# Your entry in the file can be either:
|
|
#
|
|
# eth0 eth1
|
|
#
|
|
# or
|
|
#
|
|
# eth0 192.168.0.0/24
|
|
#
|
|
# Example 2:
|
|
#
|
|
# You add a router to your local network to connect subnet
|
|
# 192.168.1.0/24 which you also want to masquerade. You then
|
|
# add a second entry for eth0 to this file:
|
|
#
|
|
# eth0 192.168.1.0/24
|
|
#
|
|
# Example 3:
|
|
#
|
|
# You have an IPSEC tunnel through ipsec0 and you want to
|
|
# masquerade packets coming from 192.168.1.0/24 but only if
|
|
# these packets are destined for hosts in 10.1.1.0/24:
|
|
#
|
|
# ipsec0:10.1.1.0/24 196.168.1.0/24
|
|
#
|
|
# Example 4:
|
|
#
|
|
# You want all outgoing traffic from 192.168.1.0/24 through
|
|
# eth0 to use source address 206.124.146.176 which is NOT the
|
|
# primary address of eth0. You want 206.124.146.176 added to
|
|
# be added to eth0 with name eth0:0.
|
|
#
|
|
# eth0:0 192.168.1.0/24 206.124.146.176
|
|
#
|
|
###############################################################################
|
|
#INTERFACE SUBNET ADDRESS PROTO PORT(S)
|
|
#LAST LINE -- ADD YOUR ENTRIES ABOVE THIS LINE -- DO NOT REMOVE
|