mirror of
https://gitlab.com/shorewall/code.git
synced 2024-12-15 10:51:02 +01:00
2617133c03
git-svn-id: https://shorewall.svn.sourceforge.net/svnroot/shorewall/trunk@4630 fbd18981-670d-0410-9b5c-8dc0c1a9a2bb
69 lines
2.4 KiB
Plaintext
69 lines
2.4 KiB
Plaintext
#
|
|
# Shorewall version 3.3 - Tcdevices File
|
|
#
|
|
# Based on tc4shorewall version 0.5 by Arne Bernin
|
|
#
|
|
# /etc/shorewall/tcdevices
|
|
#
|
|
# Entries in this file define the bandwidth for interfaces
|
|
# on which you want traffic shaping to be enabled.
|
|
#
|
|
# If you do not plan to use traffic shaping for a device,
|
|
# don't put it in here as it limits the troughput of that
|
|
# device to the limits you set here.
|
|
#
|
|
# Columns are:
|
|
#
|
|
#
|
|
# INTERFACE Name of interface. Each interface may be listed only
|
|
# once in this file. You may NOT specify the name of
|
|
# an alias (e.g., eth0:0) here; see
|
|
# http://www.shorewall.net/FAQ.htm#faq18
|
|
#
|
|
# You man NOT specify wildcards here, e.g. if you
|
|
# have multiple ppp interfaces, you need to put
|
|
# them all in here!
|
|
#
|
|
# If the device doesn't exist, a warning message will
|
|
# be issued during "shorewall [re]start" and "shorewall
|
|
# refresh" and traffic shaping configuration will be
|
|
# skipped for that device.
|
|
#
|
|
# IN-BANDWIDTH The incoming Bandwidth of that interface. Please
|
|
# note that you are not able to do traffic shaping
|
|
# on incoming traffic, as the traffic is already
|
|
# received before you could do so. But this allows
|
|
# you to define the maximum traffic allowed for
|
|
# this interface in total, if the rate is exceeded,
|
|
# the packets are dropped.
|
|
# You want this mainly if you have a DSL or Cable
|
|
# connection to avoid queuing at your providers side.
|
|
#
|
|
# If you don't want any traffic to be dropped set this
|
|
# to a value faster than your interface.
|
|
#
|
|
# Use kbit or kbps(for Kilobytes per second) for
|
|
# speed, and make sure there is NO space between the
|
|
# number and the unit.
|
|
#
|
|
# OUT-BANDWIDTH The outgoing Bandwidth of that interface.
|
|
# This is the maximum speed you connection can handle.
|
|
# It is also the speed you can refer as "full" if
|
|
# you define the tc classes.
|
|
# Outgoing traffic above this rate will be dropped.
|
|
#
|
|
# Use kbit or kbps(for Kilobytes per second) for
|
|
# speed, and make sure there is NO space between the
|
|
# number and the unit.
|
|
#
|
|
# Example 1: Suppose you are using PPP over Ethernet (DSL)
|
|
# and ppp0 is the interface for this. The
|
|
# device has an outgoing bandwidth of 500kbit and an
|
|
# incoming bandwidth of 6000kbit
|
|
# ppp0 6000kbit 500kbit
|
|
#
|
|
#
|
|
###############################################################################
|
|
#INTERFACE IN-BANDWITH OUT-BANDWIDTH
|
|
#LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE
|