and supports larger terminals than the older way.
If the new mouse-utf8 option is on, UTF-8 mouse input is enabled for all
UTF-8 terminals. The option defaults to on if LANG etc are set in the
same manner as the utf8 option.
With help and based on code from hsim at gmx.li.
this screws up the choice of most-recently-used. Instead, break the time
update into a little function and do it when the session is attached.
Pointed out by joshe@.
- server option "exit-unattached" makes the server exit when no clients
are attached, even if sessions are present;
- session option "destroy-unattached" destroys a session once no clients
are attached to it.
These are useful for preventing tmux remaining in the background where
it is undesirable and when using tmux as a login shell to keep a limit
on new sessions.
when the client tty backs up too much, just stop updating the tty and
only update the internal screen. Then when the tty recovers, force a
redraw.
This prevents a dodgy client from causing other clients to go into
backoff while still allowing tmux to be responsive (locally) when seeing
lots of output.
stdin up to the server, I forgot one essential point - the tmux server
could now be both the producer and consumer. This happens when tmux is
run inside tmux, as well as when piping tmux commands together.
So, using stdio(3) was a bad idea - if sufficient data was written, this
could block in write(2). When that happened and the server was both
producer and consumer, it deadlocks.
Change to use libevent bufferevents for the client stdin, stdout and
stderr instead. This is trivial enough for output but requires a
callback mechanism to trigger when stdin is finished.
This relies on the underlying polling mechanism for libevent to work
with whatever devices to which the user could redirect stdin, stdout or
stderr, hence the change to use poll(2) over kqueue(2) for tmux.
commands can directly make use of them. This means that load-buffer and
save-buffer can have "-" as the file to read from stdin or write to stdout.
This is a protocol version bump so the tmux server will need to be restarted
after upgrade (or an older client used).
starting tmux from .xinitrc.
One of the very few things the server relies on the client for now is to
pass through a message on SIGWINCH, but there is a condition where
potentially a SIGWINCH may be lost during the transition from unattached
(main.c) to attached (client.c). So trigger a size change immediately
after the client installs its SIGWINCH handler.
Also, when the terminal is resized, reset the scroll region and cursor
position. Previously, we were clearing our saved idea of these, but in
fact some terminals do not reset them on resize, so this caused problems
during redraw.
While here make a resize to the same size not cause a redraw and rename
the tmux.out output log file to include the tmux PID.
function. We were only ever using the client to find the session anyway.
This allows send-key to work properly for manipulating copy mode from
outside tmux.
From Micah Cowan.
window. Set and displayed with "set -s" and "show -s".
Currently the only option is "quiet" (like command-line -q, allowing it to be
set from .tmux.conf), but others will come along.
allow the format of each window in the status line window list to be controlled
using similar # sequences as status-left/right.
This diff also moves part of the way towards UTF-8 support in window names but
it isn't quite there yet.
exists. A new message-limit session option sets the maximum number of entries
and a command, show-messages, shows the log (bound to ~ by default).
This (and prompt history) might be better as a single global log but until
there are global options it is easier for them to be per client.
complicated because of escape input, but in that case instead of processing a
key immediately, schedule a timer and reprocess the bufer when it expires.
This currently assumes that keys will be atomic (ie that if eg F1 is pressed
the entire sequence is present in the buffer). This is usually but not always
true, a change in the tree format so it can differentiate potential (partial)
key sequences will happens soon and will allow this to be fixed.
This moves the client-side loops are pretty much fully over to event-based only
(tmux.c and client.c) but server-side (server.c and friends) treats libevent as
a sort of clever poll, waking up after every event to run various things.
Moving the server stuff over to bufferevents and timers and so on will come
later.
client lookup to pick the most recently used rather than the most recently
created - this is much more useful when used interactively and (because the
activity time is set at creation) should have no effect on source-file.
Based on a problem reported by Jan Johansson.
meaningful names.
Also, remove the code to try and update the session activity time for the
command client when a command message is received as is pointless because it
des not have a session.
Irritatingly, although op can be used to tell if a terminal supports default
colours, it can't be used to set them because in some terminfo descriptions it
resets attributes as a side-effect (acts as sgr0) and in others it doesn't, so
it is not possible to determine reliably what the terminal state will be
afterwards. So if AX is missing and op is present, tmux just sends sgr0.
Anyone using -d for a terminal who finds they actually needed it can replace it
using terminal-overrides, but please let me know as it is probably an omission
from terminfo.
files from server.c (merging server-msg.c into the client file) and rather than
iterating over each set after poll(), allow a callback to be specified when the
fd is added and just walk once over the returned pollfds calling each callback
where needed.
More to come, getting this in so it is tested.
