shorewall_code/docs/MultiISP.xml

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE article PUBLIC "-//OASIS//DTD DocBook XML V4.2//EN"
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd">
<article>
  <!--$Id$-->

  <articleinfo>
    <title>Shorewall and Multiple Internet Connections</title>

    <authorgroup>
      <author>
        <firstname>Tom</firstname>

        <surname>Eastep</surname>
      </author>
    </authorgroup>

    <pubdate><?dbtimestamp format="Y/m/d"?></pubdate>

    <copyright>
      <year>2005</year>

      <year>2006</year>

      <year>2007</year>

      <holder>Thomas M. Eastep</holder>
    </copyright>

    <legalnotice>
      <para>Permission is granted to copy, distribute and/or modify this
      document under the terms of the GNU Free Documentation License, Version
      1.2 or any later version published by the Free Software Foundation; with
      no Invariant Sections, with no Front-Cover, and with no Back-Cover
      Texts. A copy of the license is included in the section entitled
      <quote><ulink url="GnuCopyright.htm">GNU Free Documentation
      License</ulink></quote>.</para>
    </legalnotice>
  </articleinfo>

  <warning>
    <para>Make sure you are<emphasis role="bold"> running a current,
    vendor-supported distribution</emphasis>, before attempting to perform
    this setup, older distributions do not meet the minimum requirements,and
    you will need to recompile iptables, kernel and other software on your
    system. If you don't follow this advice,<emphasis role="bold">we will
    <emphasis role="bold">not</emphasis> be able to help
    you</emphasis>.</para>
  </warning>

  <warning>
    <para>Reading just Shorewall documentation is probably not going to give
    you enough background to use this material. Shorewall may make iptables
    easy but the Shorewall team doesn't have the resources to be able to
    spoon-feed Linux policy routing to you (please remember that the user's
    manual for a tractor doesn't teach you to grow corn either). You will
    likely need to refer to the following additional information:</para>

    <itemizedlist>
      <listitem>
        <para>The LARTC HOWTO: <ulink
        url="http://www.lartc.org">http://www.lartc.org</ulink></para>
      </listitem>

      <listitem>
        <para>Output of <command>man ip</command></para>
      </listitem>

      <listitem>
        <para>Output of <command>ip route help</command> and <command>ip rule
        help</command></para>
      </listitem>
    </itemizedlist>
  </warning>

  <section id="Support">
    <title>Multiple Internet Connection Support</title>

    <para>Beginning with Shorewall 2.3.2, limited support is included for
    multiple internet connections. Limitations of this support are as
    follows:</para>

    <itemizedlist>
      <listitem>
        <para>It utilizes static routing configuration. As such, there is no
        provision for reacting to the failure of either of the uplinks.</para>
      </listitem>

      <listitem>
        <para>The routing changes are made and the route cache is purged when
        Shorewall is started <emphasis role="bold">and when Shorewall is
        restarted</emphasis> (unless you specify the "-n" option to
        <command>shorewall restart</command>). Ideally, restarting the packet
        filter should have no effect on routing.</para>
      </listitem>

      <listitem>
        <para>Prior to Shorewall 3.4.0, the routes and route rules added by
        this support were not completely removed during <command>shorewall
        stop</command>, <command>shorewall clear</command> or
        <command>shorewall restart</command>.</para>
      </listitem>
    </itemizedlist>

    <section id="Overview">
      <title>Overview</title>

      <para>Let's assume that a firewall is connected via two separate
      ethernet interfaces to two different ISPs as in the following
      diagram.</para>

      <graphic align="center" fileref="images/TwoISPs.png" valign="middle" />

      <itemizedlist>
        <listitem>
          <para>eth0 connects to ISP1. The IP address of eth0 is
          206.124.146.176 and the ISP's gateway router has IP address
          206.124.146.254.</para>
        </listitem>

        <listitem>
          <para>eth1 connects to ISP 2. The IP address of eth1 is
          130.252.99.27 and the ISP's gateway router has IP address
          130.252.99.254.</para>
        </listitem>

        <listitem>
          <para>eth2 connects to the local LAN. Its IP configuration is not
          relevant to this discussion.</para>
        </listitem>
      </itemizedlist>

      <para>Each of these <firstterm>providers</firstterm> is described in an
      entry in the file <filename>/etc/shorewall/providers</filename>.</para>

      <para>Entries in <filename>/etc/shorewall/providers</filename> can
      specify that outgoing connections are to be load-balanced between the
      two ISPs. Entries in <filename>/etc/shorewall/tcrules</filename> can be
      used to direct particular outgoing connections to one ISP or the other.
      Use of <filename>/etc/shorewall/tcrules</filename> is not required for
      <filename>/etc/shorewall/providers</filename> to work, but you must
      select a unique MARK value for each provider so Shorewall can set up the
      correct marking rules for you.</para>

      <para>When you use the <emphasis role="bold">track</emphasis> option in
      <filename>/etc/shorewall/providers</filename>, connections from the
      internet are automatically routed back out of the correct interface and
      through the correct ISP gateway. This works whether the connection is
      handled by the firewall itself or if it is routed or port-forwarded to a
      system behind the firewall.</para>

      <para>Shorewall will set up the routing and will update the
      <filename>/etc/iproute2/rt_tables</filename> to include the table names
      and numbers of the tables that it adds.</para>

      <caution>
        <para>This feature uses <ulink url="traffic_shaping.htm">packet
        marking</ulink> to control the routing. As a consequence, there are
        some restrictions concerning entries in
        <filename>/etc/shorewall/tcrules</filename>:</para>

        <itemizedlist>
          <listitem>
            <para>Packet marking for traffic control purposes may not be done
            in the PREROUTING table for connections involving providers with
            'track' specified (see below).</para>
          </listitem>

          <listitem>
            <para>You may not use the SAVE or RESTORE options.</para>
          </listitem>

          <listitem>
            <para>You may not use connection marking.</para>
          </listitem>
        </itemizedlist>
      </caution>

      <para>The <filename>/etc/shorewall/providers</filename> file can also be
      used in other routing scenarios. See the <ulink
      url="Shorewall_Squid_Usage.html">Squid documentation</ulink> for an
      example.</para>
    </section>

    <section id="providers">
      <title>/etc/shorewall/providers File</title>

      <para>Entries in this file have the following columns. As in all
      Shorewall configuration files, enter "-" in a column if you don't want
      to enter any value.</para>

      <variablelist>
        <varlistentry>
          <term>NAME</term>

          <listitem>
            <para>The provider name. Must begin with a letter and consist of
            letters and digits. The provider name becomes the name of the
            generated routing table for this provider.</para>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>NUMBER</term>

          <listitem>
            <para>A number between 1 and 252. This becomes the routing table
            number for the generated table for this provider.</para>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>MARK</term>

          <listitem>
            <para>A mark value used in your /etc/shorewall/tcrules file to
            direct packets to this provider. Shorewall will also mark
            connections that have seen input from this provider with this
            value and will restore the packet mark in the PREROUTING CHAIN.
            Mark values must be in the range 1-255.</para>

            <para>Beginning with Shorewall version 3.2.0 Beta 6, you may use
            may set HIGH_ROUTE_MARKS=Yes in
            <filename>/etc/shorewall/shorewall.conf</filename>. This allows
            you to:</para>

            <itemizedlist>
              <listitem>
                <para>Use connection marks for traffic shaping, provided that
                you assign those marks in the FORWARD chain.</para>
              </listitem>

              <listitem>
                <para>Use mark values &gt; 255 for provider marks in this
                column. These mark values must be a multiple of 256 in the
                range 256-65280 (hex equivalent 0x100 - 0xFF00 with the
                low-order 8 bits being zero).</para>
              </listitem>
            </itemizedlist>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>DUPLICATE</term>

          <listitem>
            <para>Gives the name or number of a routing table to duplicate.
            May be 'main' or the name or number of a previously declared
            provider. For most applications, you want to specify 'main'
            here.</para>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>INTERFACE</term>

          <listitem>
            <para>The name of the interface to the provider.</para>

            <caution>
              <para>The Shorewall implementation of Multi-ISP support requires
              that each provider has its own interface -- and remember that
              "virtual interfaces" (e.g., eth0:0) are <ulink
              url="Shorewall_and_Aliased_Interfaces.html">not
              interfaces</ulink>.</para>
            </caution>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>GATEWAY</term>

          <listitem>
            <para>The IP address of the provider's Gateway router.</para>

            <para>You can enter <emphasis role="bold">detect</emphasis> here
            and Shorewall will attempt to automatically determine the gateway
            IP address.</para>

            <para><emphasis role="bold">Hint:</emphasis> <emphasis
            role="bold">"detect"</emphasis> is appropriate for use in cases
            where the interface named in the INTERFACE column is dynamically
            configured via DHCP etc.</para>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>OPTIONS</term>

          <listitem>
            <para>A comma-separated list from the following:</para>

            <variablelist>
              <varlistentry>
                <term>track</term>

                <listitem>
                  <para>If specified, connections FROM this interface are to
                  be tracked so that responses may be routed back out this
                  same interface.</para>

                  <para>You want to specify 'track' if internet hosts will be
                  connecting to local servers through this provider. Any time
                  that you specify 'track', you will also want to specify
                  'balance' (see below).</para>

                  <para>Use of this feature requires that your kernel and
                  iptables include CONNMARK target and connmark match support
                  (<emphasis role="bold">Warning</emphasis>: Standard
                  <trademark>Debian</trademark> and
                  <trademark>Ubuntu</trademark> kernels are lacking that
                  support!).</para>

                  <warning>
                    <para>A <emphasis role="bold">bug</emphasis> in Shorewall
                    versions 3.2.0-3.2.10, 3.4.0-3.4.6 and 4.0.0-4.0.2
                    prevents proper handling of PREROUTING marks when
                    HIGH_ROUTE_MARKS=No and the <emphasis
                    role="bold">track</emphasis> option is specified. Patches
                    are available to correct this problem:</para>

                    <para>Shorewall version 3.2.0-3.4.3: <ulink
                    url="http://www1.shorewall.net/pub/shorewall/3.2/shorewall-3.2.10/errata/patches/Shorewall/patch-3.2.10-2.diff">http://www1.shorewall.net/pub/shorewall/3.2/shorewall-3.2.10/errata/patches/Shorewall/patch-3.2.10-2.diff
                    </ulink></para>

                    <para>Shorewall version 3.4.4-3.4.6: <ulink
                    url="http://www1.shorewall.net/pub/shorewall/3.4/shorewall-3.4.6/errata/patches/Shorewall/patch-3.4.6-1.diff">http://www1.shorewall.net/pub/shorewall/3.4/shorewall-3.4.6/errata/patches/Shorewall/patch-3.4.6-1.diff</ulink></para>

                    <para>Shorewall-shell version 4.0.0-4.0.2: <ulink
                    url="http://www1.shorewall.net/pub/shorewall/4.0/shorewall-4.0.2/errata/patches/Shorewall-shell/patch-shell-4.0.2-2.diff">http://www1.shorewall.net/pub/shorewall/4.0/shorewall-4.0.2/errata/patches/Shorewall-shell/patch-shell-4.0.2-2.diff</ulink></para>
                  </warning>

                  <important>
                    <para>If you are using
                    <filename>/etc/shorewall/providers</filename> because you
                    have multiple internet connections, we recommend that you
                    specify 'track' even if you don't need it. It helps
                    maintain long-term connections in which there are
                    significant periods with no traffic.</para>
                  </important>
                </listitem>
              </varlistentry>

              <varlistentry>
                <term>balance</term>

                <listitem>
                  <para>The providers that have 'balance' specified will get
                  outbound traffic load-balanced among them. Balancing will
                  not be perfect, as it is route based, and routes are cached.
                  This means that routes to often-used sites will always be
                  over the same provider.</para>

                  <para>By default, each provider is given the same weight (1)
                  . You can change the weight of a given provider by following
                  <emphasis>balance</emphasis> with "=" and the desired weight
                  (e.g., balance=2). The weights reflect the relative
                  bandwidth of the providers connections and should be small
                  numbers since the kernel actually creates additional default
                  routes for each weight increment.</para>

                  <important>
                    <para>If you are using
                    <filename>/etc/shorewall/providers</filename> because you
                    have multiple internet connections, we recommend that you
                    specify 'balance' even if you don't need it. You can still
                    use entries in <filename>/etc/shorewall/tcrules</filename>
                    to force all traffic to one provider or another.<note>
                        <para>If you don't heed this advice then be prepared
                        to read <ulink url="FAQ.htm#faq57">FAQ 57</ulink> and
                        <ulink url="FAQ.htm#faq58">FAQ 58</ulink>.</para>
                      </note></para>
                  </important>

                  <important>
                    <para>If you specify 'balance' and still find that all
                    traffic is going out through only one provider, you may
                    need to install a kernel built with
                    CONFIG_IP_ROUTE_MULTIPATH_CACHED=n. Several users have
                    reported that this change has corrected similar
                    problems.</para>

                    <para>The SuSE 10.0 kernel is subject to this problem, and
                    <ulink
                    url="https://bugzilla.novell.com/show_bug.cgi?id=190908">
                    a kernel oops may result in this circumstance.</ulink>
                    SUSE 10.1 and SLES 10 have
                    CONFIG_IP_ROUTE_MULTIPATH_CACHED=n set by default. The
                    source of the problem seems to be <ulink
                    url="http://news.gmane.org/find-root.php?message_id=%3c00da01c5b35a%24b12b9860%241b00a8c0%40cruncher%3e">an
                    incompatibility between the LARTC patches and
                    CONFIG_IP_ROUTE_MULTIPATH_CACHED.</ulink></para>
                  </important>
                </listitem>
              </varlistentry>

              <varlistentry>
                <term>loose</term>

                <listitem>
                  <para>Do not include routing rules that force traffic whose
                  source IP is an address of the INTERFACE to be routed to
                  this provider. Useful for defining providers that are to be
                  used only when the appropriate packet mark is applied.
                  Should not be specified together with <emphasis
                  role="bold">balance</emphasis>.</para>
                </listitem>
              </varlistentry>

              <varlistentry>
                <term>optional (added in Shorewall 3.2.2)</term>

                <listitem>
                  <para>Shorewall will determine of this interface is up and
                  has a configured IPv4 address. If it is not, a warning is
                  issued and this provider is not configured.</para>

                  <note>
                    <para>'optional' is designed to detect interface states
                    that will cause <command>shorewall start</command> or
                    <command>shorewall restart</command> to fail; just because
                    an interface is in a state that Shorewall can [re]start
                    without error doesn't mean that traffic can actually be
                    sent through the interface.</para>

                    <para>Beginning with Shorewall-perl 4.0.3, you can supply
                    an 'isusable' <ulink
                    url="shorewall_extension_scripts.htm">extension
                    script</ulink> to extend Shorewall's interface state
                    detection.</para>
                  </note>
                </listitem>
              </varlistentry>
            </variablelist>

            <para>For those of you who are termnally confused between<emphasis
            role="bold"> track</emphasis> and <emphasis
            role="bold">balance</emphasis>:</para>

            <itemizedlist>
              <listitem>
                <para><emphasis role="bold">track</emphasis> governs incoming
                connections.</para>
              </listitem>

              <listitem>
                <para><emphasis role="bold">balance</emphasis> governs
                outgoing connections.</para>
              </listitem>
            </itemizedlist>
          </listitem>
        </varlistentry>

        <varlistentry>
          <term>COPY</term>

          <listitem>
            <para>A comma-separated list if interface names. Wildcards
            specified using an asterisk ("*") are permitted (e.g., tun*
            ).</para>

            <para>When you specify an existing table in the DUPLICATE column,
            Shorewall copies all routes through the interface specified in the
            INTERFACE column plus the interfaces listed in this column.
            Normally, you will list all interfaces on your firewall in this
            column except those internet interfaces specified in the INTERFACE
            column of entries in this file.</para>
          </listitem>
        </varlistentry>
      </variablelist>
    </section>

    <section id="Providers">
      <title>What an entry in the Providers File Does</title>

      <para>Adding another entry in the providers file simply creates an
      alternate routing table for you. In addition:</para>

      <orderedlist>
        <listitem>
          <para>Unless <emphasis role="bold">loose</emphasis> is specified, an
          ip rule is generated for each IP address on the INTERFACE that
          routes traffic from that address through the associated routing
          table.</para>
        </listitem>

        <listitem>
          <para>If you specify <emphasis role="bold">track</emphasis>, then
          connections which have had at least one packet arrive on the
          interface listed in the INTERFACE column have their connection mark
          set to the value in the MARK column. In the PREROUTING chain,
          packets with a connection mark have their packet mark set to the
          value of the associated connection mark; packets marked in this way
          bypass any prerouting rules that you create in
          <filename>/etc/shorewall/tcrules</filename>. This ensures that
          packets associated with connections from outside are always routed
          out of the correct interface.</para>
        </listitem>

        <listitem>
          <para>If you specify <emphasis role="bold">balance</emphasis>, then
          Shorewall will replace the 'default' route with weight 100 in the
          'main' routing table with a load-balancing route among those
          gateways where <emphasis role="bold">balance</emphasis> was
          specified. So if you configure default routes, be sure that their
          weight is less than 100 or the route added by Shorewall will not be
          used.</para>
        </listitem>
      </orderedlist>

      <para>That's <emphasis role="bold">all</emphasis> that these entries do.
      You still have to follow the principle stated in the <ulink
      url="Shorewall_and_Routing.html">Shorewall Routing
      documentation</ulink>:</para>

      <orderedlist>
        <listitem>
          <para>Routing determines where packets are to be sent.</para>
        </listitem>

        <listitem>
          <para>Once routing determines where the packet is to go, the
          firewall (Shorewall) determines if the packet is allowed to go
          there.</para>
        </listitem>
      </orderedlist>

      <para>The bottom line is that if you want traffic to go out through a
      particular provider then you <emphasis>must </emphasis>mark that traffic
      with the provider's MARK value in
      <filename>/etc/shorewall/tcrules</filename> and you must do that marking
      in the PREROUTING chain; or, you must provide the appropriate rules in
      <filename>/etc/shorewall/route_rules</filename>.</para>

      <warning id="Undo">
        <para>If you are running a Shorewall version prior to 3.4.0, entries
        in <filename>/etc/shorewall/providers</filename> permanently alter
        your firewall/gateway's routing; that is, the effect of these changes
        is not reversed by <command>shorewall stop</command> or
        <command>shorewall clear</command>. To restore routing to its original
        state, you may have to restart your network. This can usually be done
        by <command>/etc/init.d/network restart</command> or
        <command>/etc/init.d/networking restart</command>. Check your
        distribution's networking documentation.</para>

        <para>Here are some additional things to consider:</para>

        <itemizedlist>
          <listitem>
            <para>You can mitigate the effect of the Shorewall-generated
            changes to your routing table by specifying a
            <emphasis>metric</emphasis> for each default route that you
            configure. Shorewall will generate a load-balancing default route
            (assuming that <emphasis role="bold">balance</emphasis> has been
            specified for some of the providers) that does not include a
            metric and that will therefore not replace any existing route that
            has a non-zero metric.</para>
          </listitem>

          <listitem>
            <para>The <command>-n</command> option to <command>shorewall
            restart</command> and <command>shorewall restore</command> can be
            used to prevent the command from changing your routing.</para>
          </listitem>

          <listitem>
            <para>The <filename>/etc/shorewall/stopped</filename> file can
            also be used to restore routing when you stop Shorewall. With your
            firewall in its normal (single-table) routing configuration, you
            can capture the contents as follows:</para>

            <programlisting>ip route ls &gt; routes</programlisting>

            <para>Here's what the <filename>routes</filename> file looked like
            after I did that on my firewall:</para>

            <programlisting>192.168.1.1 dev eth3  scope link
206.124.146.177 dev eth1  scope link
192.168.2.2 dev tun0  proto kernel  scope link  src 192.168.2.1
192.168.2.0/24 via 192.168.2.2 dev tun0
192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.254
206.124.146.0/24 dev eth3  proto kernel  scope link  src 206.124.146.176
169.254.0.0/16 dev eth0  scope link
127.0.0.0/8 dev lo  scope link
default via 206.124.146.254 dev eth3</programlisting>

            <para>Now edit the file as shown below:</para>

            <programlisting><command>ip route flush table main
ip route add</command> 192.168.1.1 dev eth3  scope link
<command>ip route add </command>206.124.146.177 dev eth1  scope link
<command>ip route add </command>192.168.2.2 dev tun0  proto kernel  scope link  src 192.168.2.1
<command>ip route add </command>192.168.2.0/24 via 192.168.2.2 dev tun0
<command>ip route add </command>192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.254
<command>ip route add </command>206.124.146.0/24 dev eth3  proto kernel  scope link  src 206.124.146.176
<command>ip route add </command>169.254.0.0/16 dev eth0  scope link
<command>ip route add </command>127.0.0.0/8 dev lo  scope link
<command>ip route add </command>default via 206.124.146.254 dev eth3
<command>ip route flush cache</command></programlisting>

            <para>Now paste the contents of that file into
            <filename>/etc/shorewall/stopped</filename>.</para>

            <para>You might also want to consider adding the following to the
            file:</para>

            <programlisting><command>ip rule ls</command> | while read priority rule; do
    case ${priority%:} in
        0|3276[67])
            ;;
        *)
            ip rule del $rule
            ;;
    esac
done</programlisting>

            <para>That code will delete all but the default routing
            rules.</para>
          </listitem>
        </itemizedlist>
      </warning>
    </section>

    <section id="Provider_Doesnt">
      <title>What an entry in the Providers File Does NOT Do</title>

      <para>Given that Shorewall is simply a tool to configure Netfilter and
      does not run continuously in your system, entries in the providers file
      <emphasis role="bold">do not provide any automatic failover in the event
      of failure of one of your Internet connections</emphasis>.</para>
    </section>

    <section id="Martians">
      <title>Martians</title>

      <para>One problem that often arises with Multi-ISP configuration is
      'Martians'. If your internet interfaces are configured with the
      <emphasis role="bold">routefilter</emphasis> option in
      <filename>/etc/shorewall/interfaces</filename> (remember that if you set
      that option, you should also select <emphasis
      role="bold">logmartians</emphasis>), then things may not work correctly
      and you will see messages like this:</para>

      <programlisting>Feb  9 17:23:45 gw.ilinx kernel: martian source 206.124.146.176 from 64.86.88.116, on dev eth1 
Feb  9 17:23:45 gw.ilinx kernel: ll header: 00:a0:24:2a:1f:72:00:13:5f:07:97:05:08:00</programlisting>

      <para>The above message is somewhat awkwardly phrased. The source IP in
      this incoming packet was 64.86.88.116 and the destination IP address is
      206.124.146.176. Another gotcha is that the incoming packet has already
      had the destination IP address changed for DNAT or because the original
      outgoing connection was altered by an entry in
      <filename>/etc/shorewall/masq</filename> (SNAT or Masquerade). So the
      destination IP address (206.124.146.176) may not have been the
      destination IP address in the packet as it was initially
      received.</para>

      <para>There a couple of common causes for these problems:</para>

      <orderedlist>
        <listitem>
          <para>You have connected both of your external interfaces to the
          same hub/switch. Connecting multiple firewall interfaces to a common
          hub or switch is always a bad idea that will result in
          hard-to-diagnose problems.</para>
        </listitem>

        <listitem>
          <para>You are specifying both the <emphasis
          role="bold">loose</emphasis> and <emphasis
          role="bold">balance</emphasis> options on your provider(s). This
          causes individual connections to ping-pong back and forth between
          the interfaces which is guaranteed to cause problems.</para>
        </listitem>

        <listitem>
          <para>You are redirecting traffic from the local system out of one
          interface or the other using packet marking in your
          <filename>/etc/shorewall/tcrules</filename> file. A better approach
          is to configure the application to use the appropriate local IP
          address (the IP address of the interface that you want the
          application to use). See <link linkend="Local">below</link>.</para>
        </listitem>
      </orderedlist>

      <para>If all else fails, remove the <emphasis
      role="bold">routefilter</emphasis> option from your external interfaces.
      If you do this, you may wish to add rules to log and drop packets from
      the Internet that have source addresses in your local networks. For
      example, if the local LAN in the above diagram is 192.168.1.0/24, then
      you would add this rule:</para>

      <programlisting>#ACTION          SOURCE                     DEST
DROP:info        net:192.168.1.0/24         all</programlisting>

      <para>Be sure the above rule is added before any other rules with
      <emphasis>net</emphasis> in the SOURCE column.</para>
    </section>

    <section id="Example1">
      <title id="Example">Example</title>

      <para>The configuration in the figure at the top of this section would
      be specified in <filename>/etc/shorewall/providers</filename> as
      follows.</para>

      <programlisting>#NAME   NUMBER  MARK    DUPLICATE       INTERFACE       GATEWAY         OPTIONS          COPY
ISP1    1       1       main            eth0            206.124.146.254 track,balance    eth2
ISP2    2       2       main            eth1            130.252.99.254  track,balance    eth2</programlisting>

      <para>Other configuration files go something like this:</para>

      <para><filename>/etc/shorewall/interfaces</filename>:</para>

      <programlisting>#ZONE    INTERFACE    BROADCAST       OPTIONS
net      eth0         detect          …          
net      eth1         detect          …</programlisting>

      <para><filename>/etc/shorewall/policy</filename>:</para>

      <programlisting>#SOURCE    DESTINATION    POLICY     LIMIT:BURST
net        net            DROP</programlisting>

      <para>Regardless of whether you have masqueraded hosts or not, the
      following entries are required in
      <filename>/etc/shorewall/masq</filename> if you plan to redirect
      connections from the firewall using entries in
      <filename>/etc/shorewall/tcrules</filename> or if you specify <emphasis
      role="bold">balance</emphasis> on your providers.</para>

      <programlisting>#INTERFACE       SUBNET            ADDRESS
eth0             130.252.99.27     206.124.146.176
eth1             206.124.146.176   130.252.99.27</programlisting>

      <para>Those entries ensure that traffic originating on the firewall and
      redirected via packet marks always has the source IP address
      corresponding to the interface that it is routed out of.</para>

      <note>
        <para>If you have a Dynamic IP address on either of the interfaces,
        you can use shell variables to construct the above rules. For example,
        if <filename class="devicefile">eth0</filename> had a dynamic IP
        address, then:</para>

        <para><filename>/etc/shorewall/params</filename>:</para>

        <programlisting>ETH0_IP=$(find_first_interface_address eth0)</programlisting>

        <para>/etc/shorewall/masq:</para>

        <programlisting>#INTERFACE       SUBNET            ADDRESS
eth0             130.252.99.27     $ETH0_IP
eth1             $ETH0_IP          130.252.99.27</programlisting>
      </note>

      <para>If you have masqueraded hosts, be sure to update
      <filename>/etc/shorewall/masq</filename> to masquerade to both ISPs. For
      example, if you masquerade all hosts connected to <filename
      class="devicefile">eth2</filename> then:</para>

      <programlisting>#INTERFACE       SUBNET            ADDRESS
eth0             eth2              206.124.146.176
eth1             eth2              130.252.99.27</programlisting>

      <warning>
        <para>Entries in <filename>/etc/shorewall/masq</filename> have no
        effect on which ISP a particular connection will be sent through. That
        is rather the purpose of entries in
        <filename>/etc/shorewall/tcrules</filename> or
        <filename>/etc/shorewall/route_rules</filename>.</para>
      </warning>

      <para>Now suppose that you want to route all outgoing SMTP traffic from
      your local network through ISP 2. You would make this entry in <ulink
      url="traffic_shaping.htm">/etc/shorewall/tcrules</ulink> (and if you are
      running a version of Shorewall earlier than 3.0.0, you would set
      TC_ENABLED=Yes in <ulink
      url="???">/etc/shorewall/shorewall.conf</ulink>).</para>

      <programlisting>#MARK           SOURCE          DEST            PROTO   PORT(S) CLIENT  USER    TEST
#                                                               PORT(S)
2:P             &lt;local network&gt; 0.0.0.0/0       tcp     25</programlisting>
    </section>

    <section id="morethan2">
      <title>More than 2 Providers</title>

      <para>When there are more than two providers, you need to extend the
      two-provider case in the expected way:</para>

      <orderedlist>
        <listitem>
          <para>For each external address, you need an entry in
          <filename>/etc/shorewall/masq</filename> to handle the case where a
          connection using that address as the SOURCE is sent out of the
          interfaces other than the one that the address is configured
          on.</para>
        </listitem>

        <listitem>
          <para>For each external interface, you need to add an entry to
          <filename>/etc/shorewall/masq</filename> for each internal network
          that needs to be masqueraded (or use SNAT) through that
          interface.</para>
        </listitem>
      </orderedlist>

      <para>If we extend the above example to add eth3 with IP address
      16.105.78.4 with gateway 16.105.78.254, then:</para>

      <para><filename>/etc/shorewall/providers</filename>:<programlisting>#NAME   NUMBER  MARK    DUPLICATE       INTERFACE       GATEWAY         OPTIONS          COPY
ISP1    1       1       main            eth0            206.124.146.254 track,balance    eth2
ISP2    2       2       main            eth1            130.252.99.254  track,balance    eth2
ISP3    3       3       main            eth3            16.105.78.254   track,balance    eth2</programlisting></para>

      <para><filename>/etc/shorewall/masq</filename>:<programlisting>#INTERFACE       SUBNET            ADDRESS
eth0             130.252.99.27     206.124.146.176
eth3             130.252.99.27     16.105.78.4
eth1             206.124.146.176   130.252.99.27
eth3             206.124.146.176   16.105.78.4
eth0             16.106.78.4       206.124.146.176
eth1             16.106.78.4       130.252.99.27
eth0             eth2              206.124.146.176
eth1             eth2              130.252.99.27
eth3             eth2              16.105.78.4</programlisting></para>
    </section>

    <section id="Local">
      <title>Applications running on the Firewall</title>

      <para>Experience has shown that in some cases, problems occur with
      applications running on the firewall itself. This is especially true
      when you have specified <emphasis role="bold">routefilter</emphasis> on
      your external interfaces in /etc/shorewall/interfaces (see <link
      linkend="Martians">above</link>). When this happens, it is suggested
      that you have the application use specific local IP addresses rather
      than 0.</para>

      <para>Examples:</para>

      <itemizedlist>
        <listitem>
          <para>Squid: In <filename>squid.conf</filename>, set <emphasis
          role="bold">tcp_outgoing_address</emphasis> to the IP address of the
          interface that you want Squid to use.</para>
        </listitem>

        <listitem>
          <para>In OpenVPN, set <emphasis role="bold">local
          </emphasis>(<emphasis role="bold">--local</emphasis> on the command
          line) to the IP address that you want the server to receive
          connections on.</para>
        </listitem>
      </itemizedlist>

      <para>Note that some traffic originating on the firewall doesn't have a
      SOURCE IP address before routing. At least one Shorewall user reports
      that an entry in <filename>/etc/shorewall/route_rules</filename> with
      'lo' in the SOURCE column seems to be the most reliable way to direct
      such traffic to a particular ISP.</para>
    </section>

    <section id="route_rules">
      <title>/etc/shorewall/route_rules</title>

      <para>The <filename>/etc/shorewall/route_rules</filename> file was added
      in Shorewall version 3.2.0. The <filename>route_rules</filename> file
      allows assigning certain traffic to a particular provider just as
      entries in the <filename>tcrules</filename> file. The difference between
      the two files is that entries in <filename>route_rules</filename> are
      independent of Netfilter.</para>

      <warning>
        <para>Prior to Shorewall version 3.4.0, entries in
        <filename>/etc/shorewall/route_rules</filename> permanently alter your
        firewall/gateway's routing; that is, the effect of these changes is
        not reversed by <command>shorewall stop</command> or
        <command>shorewall clear</command>. To restore routing to its original
        state, you may have to restart your network. This can usually be done
        by <command>/etc/init.d/network restart</command> or
        <command>/etc/init.d/networking restart</command>. Check your
        distribution's networking documentation.</para>

        <para>Please also see the <link linkend="Undo">warning in the section
        above entitled <emphasis>What an Entry in the Providers File
        Does</emphasis></link>.</para>
      </warning>

      <section id="Routing_rules">
        <title>Routing Rules</title>

        <para>Routing rules are maintained by the Linux kernel and can be
        displayed using the <command>ip rule ls</command> command. When
        routing a packet, the rules are processed in turn until the packet is
        successfully routed.</para>

        <programlisting>gateway:~ # <command>ip rule ls</command>
0:      from all lookup local                &lt;=== Local (to the firewall) IP addresses
10001:  from all fwmark 0x1 lookup Blarg     &lt;=== This and the next rule are generated by the
10002:  from all fwmark 0x2 lookup Comcast        'MARK' values in /etc/shorewall/providers.
20000:  from 206.124.146.176 lookup Blarg    &lt;=== This and the next rule are generated unless
20256:  from 24.12.22.33 lookup Comcast           'loose' is specified; based in the output of 'ip addr ls'
32766:  from all lookup main                 &lt;=== This is the routing table shown by 'iproute -n'
32767:  from all lookup default              &lt;=== This table is usually empty
gateway:~ #</programlisting>

        <para>In the above example, there are two providers: Blarg and Comcast
        with MARK 1 going to Blarg and mark 2 going to Comcast.</para>
      </section>

      <section id="route_rules_columns">
        <title>Columns in the route_rules file</title>

        <para>Columns in the file are:</para>

        <variablelist>
          <varlistentry>
            <term>SOURCE (Optional)</term>

            <listitem>
              <para>An ip address (network or host) that matches the source IP
              address in a packet. May also be specified as an interface name
              optionally followed by ":" and an address. If the device 'lo' is
              specified, the packet must originate from the firewall
              itself.</para>
            </listitem>
          </varlistentry>

          <varlistentry>
            <term>DEST (Optional)</term>

            <listitem>
              <para>An ip address (network or host) that matches the
              destination IP address in a packet.</para>

              <para>If you choose to omit either SOURCE or DEST, place "-" in
              that column. Note that you may not omit both SOURCE and
              DEST.</para>
            </listitem>
          </varlistentry>

          <varlistentry>
            <term>PROVIDER</term>

            <listitem>
              <para>The provider to route the traffic through. May be
              expressed either as the provider name or the provider
              number.</para>
            </listitem>
          </varlistentry>

          <varlistentry>
            <term>PRIORITY</term>

            <listitem>
              <para>The rule's priority which determines the order in which
              the rules are processed.</para>

              <para>1000-1999 Before Shorewall-generated 'MARK' rules</para>

              <para>11000- 11999 After 'MARK' rules but before
              Shorewall-generated rules for ISP interfaces.</para>

              <para>26000-26999 After ISP interface rules but before 'default'
              rule.</para>

              <para>Rules with equal priority are applied in the order in
              which they appear in the file.</para>
            </listitem>
          </varlistentry>
        </variablelist>

        <para>Example 1: You want all traffic entering the firewall on eth1 to
        be routed through Comcast.</para>

        <programlisting>#SOURCE            DEST      PROVIDER        PRIORITY
eth1               -         Comcast         1000</programlisting>

        <para>With this entry, the output of <command>ip rule ls</command>
        would be as follows.</para>

        <para><programlisting>gateway:~ # <command>ip rule ls</command>
0:      from all lookup local
1000:   from all iif eth1 lookup Comcast
10001:  from all fwmark 0x1 lookup Blarg
10002:  from all fwmark 0x2 lookup Comcast
20000:  from 206.124.146.176 lookup Blarg
20256:  from 24.12.22.33 lookup Comcast
32766:  from all lookup main
32767:  from all lookup default
gateway:~ #</programlisting>Note that because we used a priority of 1000, the
        test for <filename class="devicefile">eth1</filename> is inserted
        before the fwmark tests.</para>

        <para>Example 2: You use OpenVPN (routed setup w/tunX) in combination
        with multiple providers. In this case you have to set up a rule to
        ensure that the OpenVPN traffic is routed back through the tunX
        interface(s) rather than through any of the providers. 10.8.0.0/24 is
        the subnet choosen in your OpenVPN configuration (server 10.8.0.0
        255.255.255.0).</para>

        <programlisting>#SOURCE                 DEST            PROVIDER        PRIORITY
-                       10.8.0.0/24     main            1000</programlisting>
      </section>
    </section>
  </section>
</article>