shorewall_code/Shorewall/shorewall.conf

481 lines
16 KiB
Plaintext
Raw Normal View History

##############################################################################
# /etc/shorewall/shorewall.conf V1.4 - Change the following variables to
# match your setup
#
# This program is under GPL [http://www.gnu.org/copyleft/gpl.htm]
#
# This file should be placed in /etc/shorewall
#
# (c) 1999,2000,2001,2002,2003 - Tom Eastep (teastep@shorewall.net)
##############################################################################
# L O G G I N G
##############################################################################
#
# General note about log levels. Log levels are a method of describing
# to syslog (8) the importance of a message and a number of parameters
# in this file have log levels as their value.
#
# Valid levels are:
#
# 7 debug
# 6 info
# 5 notice
# 4 warning
# 3 err
# 2 crit
# 1 alert
# 0 emerg
#
# For most Shorewall logging, a level of 6 (info) is appropriate. Shorewall
# log messages are generated by NetFilter and are logged using facility
# 'kern' and the level that you specifify. If you are unsure of the level
# to choose, 6 (info) is a safe bet. You may specify levels by name or by
# number.
#
# If you have build your kernel with ULOG target support, you may also
# specify a log level of ULOG (must be all caps). Rather than log its
# messages to syslogd, Shorewall will direct netfilter to log the messages
# via the ULOG target which will send them to a process called 'ulogd'.
# ulogd is available from http://www.gnumonks.org/projects/ulogd and can be
# configured to log all Shorewall message to their own log file
################################################################################
#
# LOG FILE LOCATION
#
# This variable tells the /sbin/shorewall program where to look for Shorewall
# log messages. If not set or set to an empty string (e.g., LOGFILE="") then
# /var/log/messages is assumed.
#
# WARNING: The LOGFILE variable simply tells the 'shorewall' program where to
# look for Shorewall messages.It does NOT control the destination for
# these messages. For information about how to do that, see
#
# http://www.shorewall.net/shorewall_logging.html
LOGFILE=/var/log/messages
#
# LOG MARKER
#
# Used to identify Shorewall log messages. If you are using fireparse, you must
# set this to "fp=Shorewall:". You may not use the ULOG level with fireparse and
# you must not embed white space in the LOGMARKER value.
LOGMARKER="Shorewall:"
#
# LOG RATE LIMITING
#
# The next two variables can be used to control the amount of log output
# generated. LOGRATE is expressed as a number followed by an optional
# `/second', `/minute', `/hour', or `/day' suffix and specifies the maximum
# rate at which a particular message will occur. LOGBURST determines the
# maximum initial burst size that will be logged. If set empty, the default
# value of 5 will be used.
#
# Example:
#
# LOGRATE=10/minute
# LOGBURST=5
#
# If BOTH variables are set empty then logging will not be rate-limited.
#
LOGRATE=
LOGBURST=
#
# LEVEL AT WHICH TO LOG 'UNCLEAN' PACKETS
#
# This variable determines the level at which Mangled/Invalid packets are logged
# under the 'dropunclean' interface option. If you set this variable to an
# empty value (e.g., LOGUNCLEAN= ), Mangled/Invalid packets will be dropped
# silently.
#
# The value of this variable also determines the level at which Mangled/Invalid
# packets are logged under the 'logunclean' interface option. If the variable
# is empty, these packets will still be logged at the 'info' level.
#
# See the comment at the top of this section for a description of log levels
#
LOGUNCLEAN=info
#
# BLACKLIST LOG LEVEL
#
# Set this variable to the syslogd level that you want blacklist packets logged
# (beware of DOS attacks resulting from such logging). If not set, no logging
# of blacklist packets occurs.
#
# See the comment at the top of this section for a description of log levels
#
BLACKLIST_LOGLEVEL=
#
# LOGGING 'New not SYN' rejects
#
# This variable only has an effect when NEWNOTSYN=No (see below).
#
# When a TCP packet that does not have the SYN flag set and the ACK and RST
# flags clear then unless the packet is part of an established connection,
# it will be rejected by the firewall. If you want these rejects logged,
# then set LOGNEWNOTSYN to the syslog log level at which you want them logged.
#
# See the comment at the top of this section for a description of log levels
#
# Example: LOGNEWNOTSYN=debug
LOGNEWNOTSYN=
#
# MAC List Log Level
#
# Specifies the logging level for connection requests that fail MAC
# verification. If set to the empty value (MACLIST_LOG_LEVEL="") then
# such connection requests will not be logged.
#
# See the comment at the top of this section for a description of log levels
#
MACLIST_LOG_LEVEL=info
#
# TCP FLAGS Log Level
#
# Specifies the logging level for packets that fail TCP Flags
# verification. If set to the empty value (TCP_FLAGS_LOG_LEVEL="") then
# such packets will not be logged.
#
# See the comment at the top of this section for a description of log levels
#
TCP_FLAGS_LOG_LEVEL=info
#
# RFC1918 Log Level
#
# Specifies the logging level for packets that fail RFC 1918
# verification. If set to the empty value (RFC1918_LOG_LEVEL="") then
# RFC1918_LOG_LEVEL=info is assumed.
#
# See the comment at the top of this section for a description of log levels
#
RFC1918_LOG_LEVEL=info
################################################################################
# L O C A T I O N O F F I L E S A N D D I R E C T O R I E S
################################################################################
#
# PATH - Change this if you want to change the order in which Shorewall
# searches directories for executable files.
#
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin:/usr/local/sbin
# SUBSYSTEM LOCK FILE
#
# Set this to the name of the lock file expected by your init scripts. For
# RedHat, this should be /var/lock/subsys/shorewall. On Debian, it
# should be /var/state/shorewall. If your init scripts don't use lock files,
# set this to "".
#
SUBSYSLOCK=/var/lock/subsys/shorewall
#
# SHOREWALL TEMPORARY STATE DIRECTORY
#
# This is the directory where the firewall maintains state information while
# it is running
#
STATEDIR=/var/lib/shorewall
#
# KERNEL MODULE DIRECTORY
#
# If your netfilter kernel modules are in a directory other than
# /lib/modules/`uname -r`/kernel/net/ipv4/netfilter then specify that
# directory in this variable. Example: MODULESDIR=/etc/modules.
MODULESDIR=
################################################################################
# F I R E W A L L O P T I O N S
################################################################################
# NAME OF THE FIREWALL ZONE
#
# Name of the firewall zone -- if not set or if set to an empty string, "fw"
# is assumed.
#
FW=fw
#
# ENABLE NAT SUPPORT
#
# You probally want yes here. Only gateways not doing NAT in any form, like
# SNAT,DNAT masquerading, port forwading etc. should say "no" here.
#
NAT_ENABLED=Yes
#
# ENABLE MANGLE SUPPORT
#
# If you say "no" here, Shorewall will ignore the /etc/shorewall/tos file
# and will not initialize the mangle table when starting or stopping
# your firewall. You must enable mangling if you want Traffic Shaping
# (see TC_ENABLED below).
#
MANGLE_ENABLED=Yes
#
# ENABLE IP FORWARDING
#
# If you say "On" or "on" here, IPV4 Packet Forwarding is enabled. If you
# say "Off" or "off", packet forwarding will be disabled. You would only want
# to disable packet forwarding if you are installing Shorewall on a
# standalone system or if you want all traffic through the Shorewall system
# to be handled by proxies.
#
# If you set this variable to "Keep" or "keep", Shorewall will neither
# enable nor disable packet forwarding.
#
IP_FORWARDING=On
#
# AUTOMATICALLY ADD NAT IP ADDRESSES
#
# If you say "Yes" or "yes" here, Shorewall will automatically add IP addresses
# for each NAT external address that you give in /etc/shorewall/nat. If you say
# "No" or "no", you must add these aliases youself.
#
ADD_IP_ALIASES=Yes
#
# AUTOMATICALLY ADD SNAT IP ADDRESSES
#
# If you say "Yes" or "yes" here, Shorewall will automatically add IP addresses
# for each SNAT external address that you give in /etc/shorewall/masq. If you say
# "No" or "no", you must add these aliases youself. LEAVE THIS SET TO "No" unless
# you are sure that you need it -- most people don't!!!
#
ADD_SNAT_ALIASES=No
#
# ENABLE TRAFFIC SHAPING
#
# If you say "Yes" or "yes" here, Traffic Shaping is enabled in the firewall. If
# you say "No" or "no" then traffic shaping is not enabled. If you enable traffic
# shaping you must have iproute[2] installed (the "ip" and "tc" utilities) and
# you must enable packet mangling above.
#
TC_ENABLED=No
#
# Clear Traffic Shapping/Control
#
# If this option is set to 'No' then Shorewall won't clear the current
# traffic control rules during [re]start. This setting is intended
# for use by people that prefer to configure traffic shaping when
# the network interfaces come up rather than when the firewall
# is started. If that is what you want to do, set TC_ENABLED=Yes and
# CLEAR_TC=No and do not supply an /etc/shorewall/tcstart file. That
# way, your traffic shaping rules can still use the 'fwmark'
# classifier based on packet marking defined in /etc/shorewall/tcrules.
#
# If omitted, CLEAR_TC=Yes is assumed.
CLEAR_TC=Yes
#
# Mark Packets in the forward chain
#
# When processing the tcrules file, Shorewall normally marks packets in the
# PREROUTING chain. To cause Shorewall to use the FORWARD chain instead, set
# this to "Yes". If not specified or if set to the empty value (e.g.,
# MARK_IN_FORWARD_CHAIN="") then MARK_IN_FORWARD_CHAIN=No is assumed.
#
# Marking packets in the FORWARD chain has the advantage that inbound
# packets destined for Masqueraded/SNATed local hosts have had their destination
# address rewritten so they can be marked based on their destination. When
# packets are marked in the PREROUTING chain, packets destined for
# Masqueraded/SNATed local hosts still have a destination address corresponding
# to the firewall's external interface.
#
# Note: Older kernels do not support marking packets in the FORWARD chain and
# setting this variable to Yes may cause startup problems.
MARK_IN_FORWARD_CHAIN=No
#
# MSS CLAMPING
#
# Set this variable to "Yes" or "yes" if you want the TCP "Clamp MSS to PMTU"
# option. This option is most commonly required when your internet
# interface is some variant of PPP (PPTP or PPPoE). Your kernel must
# have CONFIG_IP_NF_TARGET_TCPMSS set.
#
# [From the kernel help:
#
# This option adds a `TCPMSS' target, which allows you to alter the
# MSS value of TCP SYN packets, to control the maximum size for that
# connection (usually limiting it to your outgoing interface's MTU
# minus 40).
#
# This is used to overcome criminally braindead ISPs or servers which
# block ICMP Fragmentation Needed packets. The symptoms of this
# problem are that everything works fine from your Linux
# firewall/router, but machines behind it can never exchange large
# packets:
# 1) Web browsers connect, then hang with no data received.
# 2) Small mail works fine, but large emails hang.
# 3) ssh works fine, but scp hangs after initial handshaking.
# ]
#
# If left blank, or set to "No" or "no", the option is not enabled.
#
CLAMPMSS=No
#
# ROUTE FILTERING
#
# Set this variable to "Yes" or "yes" if you want kernel route filtering on all
# interfaces (anti-spoofing measure).
#
# If this variable is not set or is set to the empty value, "No" is assumed.
# In that case, you can still enable route filtering on individual interfaces
# in the /etc/shorewall/interfaces file.
ROUTE_FILTER=No
#
# NAT BEFORE RULES
#
# Shorewall has traditionally processed static NAT rules before port forwarding
# rules. If you would like to reverse the order, set this variable to "No".
#
# If this variable is not set or is set to the empty value, "Yes" is assumed.
NAT_BEFORE_RULES=Yes
# MULTIPORT support
#
# If your kernel includes the multiport match option
# (CONFIG_IP_NF_MATCH_MULTIPORT), you may enable it's use here. When this
# option is enabled by setting it's value to "Yes" or "yes":
#
# 1) If you list more that 15 ports in a comma-seperated list in
# /etc/shorewall/rules, Shorewall will not use the multiport option
# but will generate a separate rule for each element of each port
# list.
# 2) If you include a port range (<low port>:<high port>) in the
# rule, Shorewall will not use the multiport option but will generate
# a separate rule for each element of each port list.
#
# See the /etc/shorewall/rules file for additional information on this option.
#
# if this variable is not set or is set to the empty value, "No" is assumed.
MULTIPORT=No
# DNAT IP ADDRESS DETECTION
#
# Normally when Shorewall encounters the following rule:
#
# DNAT net loc:192.168.1.3 tcp 80
#
# it will forward TCP port 80 connections from the net to 192.168.1.3
# REGARDLESS OF THE ORIGINAL DESTINATION ADDRESS. This behavior is
# convenient for two reasons:
#
# a) If the the network interface has a dynamic IP address, the
# firewall configuration will work even when the address
# changes.
#
# b) It saves having to configure the IP address in the rule
# while still allowing the firewall to be started before the
# internet interface is brought up.
#
# This default behavior can also have a negative effect. If the
# internet interface has more than one IP address then the above
# rule will forward connection requests on all of these addresses;
# that may not be what is desired.
#
# By setting DETECT_DNAT_IPADDRS=Yes, rules such as the above will apply
# only if the original destination address is the primary IP address of
# one of the interfaces associated with the source zone. Note that this
# requires all interfaces to the source zone to be up when the firewall
# is [re]started.
DETECT_DNAT_IPADDRS=No
#
# MUTEX TIMEOUT
#
# The value of this variable determines the number of seconds that programs
# will wait for exclusive access to the Shorewall lock file. After the number
# of seconds corresponding to the value of this variable, programs will assume
# that the last program to hold the lock died without releasing the lock.
#
# If not set or set to the empty value, a value of 60 (60 seconds) is assumed.
#
# An appropriate value for this parameter would be twice the length of time
# that it takes your firewall system to process a "shorewall restart" command.
MUTEX_TIMEOUT=60
#
# NEWNOTSYN
#
# If this variable is set to "No" or "no", then When a TCP packet that does
# not have the SYN flag set and the ACK and RST flags clear then unless the
# packet is part of an established connection, it will be dropped by the
# firewall
#
# If this variable is set to "Yes" or "yes" then such packets will not be
# dropped but will pass through the normal rule processing.
#
# Users with a High-availability setup with two firewall's and one acting
# as a backup should set NEWNOTSYN=Yes. Users with asymmetric routing may
# also need to select NEWNOTSYN=Yes.
NEWNOTSYN=No
################################################################################
# P A C K E T D I S P O S I T I O N
################################################################################
#
# BLACKLIST DISPOSITION
#
# Set this variable to the action that you want to perform on packets from
# Blacklisted systems. Must be DROP or REJECT. If not set or set to empty,
# DROP is assumed.
#
BLACKLIST_DISPOSITION=DROP
#
# MAC List Disposition
#
# This variable determines the disposition of connection requests arriving
# on interfaces that have the 'maclist' option and that are from a device
# that is not listed for that interface in /etc/shorewall/maclist. Valid
# values are ACCEPT, DROP and REJECT. If not specified or specified as
# empty (MACLIST_DISPOSITION="") then REJECT is assumed
MACLIST_DISPOSITION=REJECT
#
# TCP FLAGS Disposition
#
# This variable determins the disposition of packets having an invalid
# combination of TCP flags that are received on interfaces having the
# 'tcpflags' option specified in /etc/shorewall/interfaces. If not specified
# or specified as empty (TCP_FLAGS_DISPOSITION="") then DROP is assumed.
TCP_FLAGS_DISPOSITION=DROP
#LAST LINE -- DO NOT REMOVE