Description

shorewall-interfaces 5 interfaces Shorewall interfaces file /etc/shorewall/interfaces Description The interfaces file serves to define the firewall's network interfaces to Shorewall. The columns in the file are as follows. ZONE Zone for this interface. Must match the name of a zone defined in /etc/shorewall/zones. You may not list the firewall zone in this column. If the interface serves multiple zones that will be defined in the /etc/shorewall/hosts file, you should place "-" in this column. If there are multiple interfaces to the same zone, you must list them in separate entries. Example:

#ZONE INTERFACE BROADCAST loc eth1 - loc eth2 -

INTERFACE Name of interface. Each interface may be listed only once in this file. You may NOT specify the name of an alias (e.g., eth0:0) here; see http://www.shorewall.net/FAQ.htm#faq18 You may specify wildcards here. For example, if you want to make an entry that applies to all PPP interfaces, use 'ppp+'. There is no need to define the loopback interface (lo) in this file. BROADCAST (Optional) The broadcast address for the subnetwork to which the interface belongs. For P-T-P interfaces, this column is left blank.If the interface has multiple addresses on multiple subnets then list the broadcast addresses as a comma-separated list. If you use the special value "detect", Shorewall will detect the broadcast address(es) for you. If you select this option, the interface must be up before the firewall is started. If you don't want to give a value for this column but you want to enter a value in the OPTIONS column, enter "-" in this column. OPTIONS (Optional) A comma-separated list of options from the following list. The order in which you list the options is not significant but the list should have no embedded white space. dhcp Specify this option when any of the following are true: the interface gets its IP address via DHCP the interface is used by a DHCP server running on the firewall you have a static IP but are on a LAN segment with lots of DHCP clients. the interface is a bridge with a DHCP server on one port and DHCP clients on another port. norfc1918 This interface should not receive any packets whose source is in one of the ranges reserved by RFC 1918 (i.e., private or "non-routable" addresses). If packet mangling or connection-tracking match is enabled in your kernel, packets whose destination addresses are reserved by RFC 1918 are also rejected. routefilter Turn on kernel route filtering for this interface (anti-spoofing measure). This option can also be enabled globally in the shorewall.conf(5) file. logmartians Turn on kernel martian logging (logging of packets with impossible source addresses. It is suggested that if you set routefilter on an interface that you also set logmartians. This option may also be enabled globally in the shorewall.conf(5) file. blacklist Check packets arriving on this interface against the shorewall-blacklist(5) file. maclist Connection requests from this interface are compared against the contents of shorewall-maclist(5). If this option is specified, the interface must be an ethernet NIC and must be up before Shorewall is started. tcpflags Packets arriving on this interface are checked for certain illegal combinations of TCP flags. Packets found to have such a combination of flags are handled according to the setting of TCP_FLAGS_DISPOSITION after having been logged according to the setting of TCP_FLAGS_LOG_LEVEL. proxyarp Sets /proc/sys/net/ipv4/conf/interface/proxy_arp. Do NOT use this option if you are employing Proxy ARP through entries in shorewall-proxyarp(5). This option is intended solely for use with Proxy ARP sub-networking as described at: http://www.tldp.org/HOWTO/mini/Proxy-ARP-Subnet routeback If specified, indicates that Shorewall should include rules that allow filtering traffic arriving on this interface back out that same interface. arp_filter If specified, this interface will only respond to ARP who-has requests for IP addresses configured on the interface. If not specified, the interface can respond to ARP who-has requests for IP addresses on any of the firewall's interface. The interface must be up when Shorewall is started. arp_ignore[=number] If specified, this interface will respond to arp requests based on the value of number (defaults to 1). 1 - reply only if the target IP address is local address configured on the incoming interface 2 - reply only if the target IP address is local address configured on the incoming interface and both with the sender's IP address are part from same subnet on this interface 3 - do not reply for local addresses configured with scope host, only resolutions for global and link 4-7 - reserved 8 - do not reply for all local addresses Do not specify arp_ignore for any interface involved in Proxy ARP. nosmurfs Filter packets for smurfs (packets with a broadcast address as the source). Smurfs will be optionally logged based on the setting of SMURF_LOG_LEVEL in shorewall.conf(5). After logging, the packets are dropped. detectnets Automatically taylors the zone named in the ZONE column to include only those hosts routed through the interface. Do not set the detectnets option on your internet interface. sourceroute If this option is not specified for an interface, then source-routed packets will not be accepted from that interface (sets /proc/sys/net/ipv4/conf/interface/accept_source_route to 1). Only set this option if you know what you are doing. This might represent a security risk and is not usually needed. upnp Incoming requests from this interface may be remapped via UPNP (upnpd). Example Example 1: Suppose you have eth0 connected to a DSL modem and eth1 connected to your local network and that your local subnet is 192.168.1.0/24. The interface gets it's IP address via DHCP from subnet 206.191.149.192/27. You have a DMZ with subnet 192.168.2.0/24 using eth2. Your entries for this setup would look like: #ZONE INTERFACE BROADCAST OPTIONS net eth0 206.191.149.223 dhcp loc eth1 192.168.1.255 dmz eth2 192.168.2.255 Example 2: The same configuration without specifying broadcast addresses is: #ZONE INTERFACE BROADCAST OPTIONS net eth0 detect dhcp loc eth1 detect dmz eth2 detect Example 3: You have a simple dial-in system with no ethernet connections. #ZONE INTERFACE BROADCAST OPTIONS net ppp0 - FILES /etc/shorewall/interfaces See ALSO shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall-ipsec(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-route_routes(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5)