Shorewall Setup Guide
Tom
Eastep
2003-12-24
2001-2003
Thomas M. Eastep
Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU Free Documentation License, Version
1.2 or any later version published by the Free Software Foundation; with
no Invariant Sections, with no Front-Cover, and with no Back-Cover
Texts. A copy of the license is included in the section entitled "GNU Free Documentation License".
Introduction
This guide is intended for users who are setting up Shorewall in an
environment where a set of public IP addresses must be managed or who want
to know more about Shorewall than is contained in the single-address guides.
Because the range of possible applications is so broad, the Guide will
give you general guidelines and will point you to other resources as
necessary.
If you run LEAF Bering, your Shorewall configuration is NOT what I
release -- I suggest that you consider installing a stock Shorewall lrp
from the shorewall.net site before you proceed. Shorewall requires that
the iproute/iproute2 package be installed (on RedHat, the package is
called iproute). You can tell if this package is installed by the
presence of an ip program on your
firewall system. As root, you can use the 'which' command to
check for this program:
[root@gateway root]# which ip
/sbin/ip
[root@gateway root]#
I recommend that you first read through the guide to familiarize
yourself with what's involved then go back through it again making
your configuration changes. Points at which configuration changes are
recommended are flagged with .
If you edit your configuration files on a Windows system, you must
save them as Unix files if your editor supports that option or you must
run them through dos2unix before trying to use them with Shorewall.
Similarly, if you copy a configuration file from your Windows hard drive
to a floppy disk, you must run dos2unix against the copy before using it
with Shorewall.
Windows
Version of dos2unix
Linux
Version of dos2unix
Shorewall Concepts
The configuration
files for Shorewall are contained in the directory /etc/shorewall -- for
most setups, you will only need to deal with a few of these as described
in this guide. Skeleton files are created during the Shorewall Installation Process.
As each file is introduced, I suggest that you look through the
actual file on your system -- each file contains detailed configuration
instructions and some contain default entries.
Shorewall views the network where it is running as being composed of
a set of zones. In the default installation, the following zone names are
used:
Zones
Name
Description
net
The Internet
loc
Your Local Network
dmz
Demilitarized Zone
Zones are defined in the file /etc/shorewall/zones.
Shorewall also recognizes the firewall system as its own zone - by
default, the firewall itself is known as fw but that may be changed in the
/etc/shorewall/shorewall.conf
file. In this guide, the default name (fw) will be used. With the
exception of fw, Shorewall attaches
absolutely no meaning to zone names. Zones are entirely what YOU make of
them. That means that you should not expect Shorewall to do something
special "because this is the internet zone" or "because that
is the DMZ".
Edit the
/etc/shorewall/zones file and make any changes necessary.
Rules about what traffic to allow and what traffic to deny are
expressed in terms of zones.
You express your default policy for connections from one zone to
another zone in the /etc/shorewall/policy
file.
You define exceptions to those default policies in the /etc/shorewall/rules.
Shorewall is built on top of the Netfilter kernel facility.
Netfilter implements a connection
tracking function that allows what is often referred to as
stateful inspection of packets. This stateful property allows firewall
rules to be defined in terms of connections rather than in terms of
packets. With Shorewall, you:
Identify the source zone.
Identify destination zone.
If the POLICY from the client's zone to the server's
zone is what you want for this client/server pair, you need do nothing
further.
If the POLICY is not what you want, then you must add a rule.
That rule is expressed in terms of the client's zone and the
server's zone.
Just because connections of a particular type are allowed from zone
A to the firewall and are also allowed from the firewall to zone B
DOES NOT mean that these connections are allowed
from zone A to zone B. It rather means that you can have a
proxy running on the firewall that accepts a connection from zone A and
then establishes its own separate connection from the firewall to zone B.
For each connection request entering the firewall, the request is
first checked against the /etc/shorewall/rules file. If no rule in that
file matches the connection request then the first policy in
/etc/shorewall/policy that matches the request is applied. If that policy
is REJECT or DROP the request is first checked against the rules in
/etc/shorewall/common.def.
The default /etc/shorewall/policy file has the following policies:
/etc/shorewall/policy
SOURCE ZONE
DESTINATION ZONE
POLICY
LOG LEVEL
LIMIT:BURST
fw
net
ACCEPT
net
all
DROP
info
all
all
REJECT
info
The above policy will:
allow all connection requests from your local network to the
internet
drop (ignore) all connection requests from the internet to your
firewall or local network and log a message at the info level (here is
a description of log levels).
reject all other connection requests and log a message at the
info level. When a request is rejected, the firewall will return an
RST (if the protocol is TCP) or an ICMP port-unreachable packet for
other protocols.
At this point, edit
your /etc/shorewall/policy and make any changes that you wish.
Network Interfaces
For the remainder of this guide, we'll refer to the following
diagram. While it may not look like your own network, it can be used to
illustrate the important aspects of Shorewall configuration.
In this diagram:
The DMZ Zone consists of systems DMZ 1 and DMZ 2. A DMZ is used
to isolate your internet-accessible servers from your local systems so
that if one of those servers is compromised, you still have the
firewall between the compromised system and your local systems.
The Local Zone consists of systems Local 1, Local 2 and Local 3.
All systems from the ISP outward comprise the Internet Zone.
![]()
The simplest way to define zones is to simply associate the zone
name (previously defined in /etc/shorewall/zones) with a network
interface. This is done in the /etc/shorewall/interfaces
file. The firewall illustrated above has three network interfaces. Where
Internet connectivity is through a cable or DSL "Modem", the
External Interface will be the Ethernet adapter that
is connected to that "Modem" (e.g., eth0)
unless you connect via Point-to-Point Protocol over Ethernet (PPPoE) or
Point-to-Point Tunneling Protocol (PPTP) in which case the External
Interface will be a ppp interface (e.g., ppp0).
If you connect via a regular modem, your External Interface will also be
ppp0. If you connect using ISDN, you
external interface will be ippp0.
If your external
interface is ppp0 or ippp0 then you will want to set CLAMPMSS=yes in
/etc/shorewall/shorewall.conf.
Your Local Interface will be an Ethernet
adapter (eth0, eth1
or eth2) and will be connected to a hub
or switch. Your local computers will be connected to the same switch
(note: If you have only a single local system, you can connect the
firewall directly to the computer using a cross-over cable).
Your DMZ Interface will also be an Ethernet
adapter (eth0, eth1
or eth2) and will be connected to a hub
or switch. Your DMZ computers will be connected to the same switch (note:
If you have only a single DMZ system, you can connect the firewall
directly to the computer using a cross-over cable).
Do not connect the internal and external interface to the same hub
or switch except for testing AND you are running Shorewall version 1.4.7
or later. When using these recent versions, you can test using this kind
of configuration if you specify the arp_filter option in
/etc/shorewall/interfaces for all interfaces connected to the common
hub/switch. Using such a setup with a production firewall is strongly
recommended against.
For the remainder of this Guide, we will assume that:
The External Interface is eth0.
The Local Interface eth1.
The DMZ Interface eth2.
The Shorewall default configuration does not define the contents of
any zone. To define the above configuration using the /etc/shorewall/interfaces file,
that file would might contain:
/etc/shorewall/interfaces
ZONE
INTERFACE
BROADCAST
OPTIONS
net
eth0
detect
rfc1918
loc
eth1
detect
dmz
eth2
detect
Edit the
/etc/shorewall/interfaces file and define the network interfaces on your
firewall and associate each interface with a zone. If you have a zone that
is interfaced through more than one interface, simply include one entry
for each interface and repeat the zone name as many times as necessary.
Example:
/etc/shorewall/interfaces
ZONE
INTERFACE
BROADCAST
OPTIONS
net
eth0
detect
rfc1918
loc
eth1
detect
dmz
eth2
detect
dhcp
You may define more
complicated zones using the /etc/shorewall/hosts
file but in most cases, that isn't necessary.
Addressing, Subnets and Routing
Normally, your ISP will assign you a set of Public IP addresses. You
will configure your firewall's external interface to use one of those
addresses permanently and you will then have to decide how you are going
to use the rest of your addresses. Before we tackle that question though,
some background is in order.
If you are thoroughly familiar with IP addressing and routing, you
may go to the next section.
The following discussion barely scratches the surface of addressing
and routing. If you are interested in learning more about this subject, I
highly recommend "IP Fundamentals: What Everyone Needs to
Know about Addressing & Routing", Thomas A. Maufer,
Prentice-Hall, 1999, ISBN 0-13-975483-0.
IP Addresses
IP version 4 (IPv4) addresses are 32-bit numbers. The notation
w.x.y.z refers to an address where the high-order byte has value
"w", the next byte has value "x", etc. If we take the
address 192.0.2.14 and express it in hexadecimal, we get:
C0.00.02.0Eor looking at
it as a 32-bit integer
C000020E
Subnets
You will still hear the terms "Class A network",
"Class B network" and "Class C network". In the early
days of IP, networks only came in three sizes (there were also Class D
networks but they were used differently):
Class A - netmask 255.0.0.0, size = 2 ** 24
Class B - netmask 255.255.0.0, size = 2 ** 16
Class C - netmask 255.255.255.0, size = 256
The class of a network was uniquely determined by the value of the
high order byte of its address so you could look at an IP address and
immediately determine the associated netmask. The netmask is a number
that when logically ANDed with an address isolates the network number;
the remainder of the address is the host number. For example, in the
Class C address 192.0.2.14, the network number is hex C00002 and the
host number is hex 0E.
As the internet grew, it became clear that such a gross
partitioning of the 32-bit address space was going to be very limiting
(early on, large corporations and universities were assigned their own
class A network!). After some false starts, the current technique of
subnetting these networks into smaller subnetworks evolved; that
technique is referred to as Classless InterDomain Routing
(CIDR). Today, any system that you are likely to work with will
understand CIDR and Class-based networking is largely a thing of the
past.
A subnetwork (often referred to as a
subnet) is a contiguous set of IP addresses such
that:
The number of addresses in the set is a power of 2; and
The first address in the set is a multiple of the set size.
The first address in the subnet is reserved and is referred to
as the subnet address.
The last address in the subnet is reserved as the subnet's
broadcast address.
As you can see by this definition, in each subnet of size n there
are (n - 2) usable addresses (addresses that can be assigned to hosts).
The first and last address in the subnet are used for the subnet address
and subnet broadcast address respectively. Consequently, small
subnetworks are more wasteful of IP addresses than are large ones.
Since n is a power of two, we can easily calculate the
Natural Logarithm (log2) of n. For the more common
subnet sizes, the size and its natural logarithm are given in the
following table:
Natural Logarithms
n
log2 n
(32 - log2 n)
8
3
29
16
4
28
32
5
27
64
6
26
128
7
25
256
8
24
512
9
23
1024
10
22
2048
11
21
4096
12
20
8192
13
19
16384
14
18
32768
15
17
65536
16
16
You will notice that the above table also contains a column for
(32 - log2 n). That number is the
Variable Length Subnet Mask (VLSM) for a network of
size n. From the above table, we can derive the following one which is a
little easier to use.
VLSM
Subnet Size
VLSM
Subnet Mask
8
/29
255.255.255.248
16
/28
255.255.255.240
32
/27
255.255.255.224
64
/26
255.255.255.192
128
/25
255.255.255.128
256
/24
255.255.255.0
512
/23
255.255.254.0
1024
/22
255.255.252.0
2048
/21
255.255.248.0
4096
/20
255.255.240.0
8192
/19
255.255.224.0
16384
/18
255.255.192.0
32768
/17
255.255.128.0
65536
/16
255.255.0.0
2 ** 24
/8
255.0.0.0
Notice that the VLSM is written with a slash ("/") -- you
will often hear a subnet of size 64 referred to as a "slash 26"
subnet and one of size 8 referred to as a "slash 29".
The subnet's mask (also referred to as its
netmask) is simply a 32-bit number with the first
"VLSM" bits set to one and the remaining bits set to zero. For
example, for a subnet of size 64, the subnet mask has 26 leading one
bits:
11111111111111111111111111000000 = FFFFFFC0 = FF.FF.FF.C0 = 255.255.255.192The
subnet mask has the property that if you logically AND the subnet mask
with an address in the subnet, the result is the subnet address. Just as
important, if you logically AND the subnet mask with an address outside
the subnet, the result is NOT the subnet address. As we will see below,
this property of subnet masks is very useful in routing.
For a subnetwork whose address is a.b.c.d
and whose Variable Length Subnet Mask is /v,
we denote the subnetwork as "a.b.c.d/v"
using CIDR Notation. Example:
Subnet
Subnet:
10.10.10.0 - 10.10.10.127
Subnet Size:
128
Subnet Address:
10.10.10.0
Broadcast Address:
10.10.10.127
CIDR Notation:
10.10.10.0/25
There are two degenerate subnets that need mentioning; namely, the
subnet with one member and the subnet with 2 ** 32 members.
/32 and /0
Subnet Size
VLSM Length
Subnet Mask
CIDR Notation
1
32
255.255.255.255
a.b.c.d/32
32
0
0.0.0.0
0.0.0.0/0
So any address a.b.c.d may also
be written a.b.c.d/32 and the set of
all possible IP addresses is written 0.0.0.0/0.
Later in this guide, you will see the notation
a.b.c.d/v used to describe the ip
configuration of a network interface (the 'ip' utility also uses
this syntax). This simply means that the interface is configured with ip
address a.b.c.d and with the netmask
that corresponds to VLSM /v.
Example: 192.0.2.65/29 The interface is configured with IP address 192.0.2.65 and netmask 255.255.255.248.
Beginning with Shorewall 1.4.6, /sbin/shorewall supports an
ipcalc command that automatically calculates information about a
[sub]network.
Example 1:shorewall ipcalc 10.10.10.0/25
CIDR=10.10.10.0/25
NETMASK=255.255.255.128
NETWORK=10.10.10.0
BROADCAST=10.10.10.127
Example 2:shorewall ipcalc 10.10.10.0 255.255.255.128
CIDR=10.10.10.0/25
NETMASK=255.255.255.128
NETWORK=10.10.10.0
BROADCAST=10.10.10.127
Routing
One of the purposes of subnetting is that it forms the basis for
routing. Here's the routing table on my firewall:
[root@gateway root]# netstat -nr
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.9.1 0.0.0.0 255.255.255.255 UH 40 0 0 texas
206.124.146.177 0.0.0.0 255.255.255.255 UH 40 0 0 eth1
206.124.146.180 0.0.0.0 255.255.255.255 UH 40 0 0 eth3
192.168.3.0 0.0.0.0 255.255.255.0 U 40 0 0 eth3
192.168.2.0 0.0.0.0 255.255.255.0 U 40 0 0 eth1
192.168.1.0 0.0.0.0 255.255.255.0 U 40 0 0 eth2
206.124.146.0 0.0.0.0 255.255.255.0 U 40 0 0 eth0
192.168.9.0 192.0.2.223 255.255.255.0 UG 40 0 0 texas
127.0.0.0 0.0.0.0 255.0.0.0 U 40 0 0 lo
0.0.0.0 206.124.146.254 0.0.0.0 UG 40 0 0 eth0
[root@gateway root]#
The device texas is a GRE tunnel to a peer
site in the Dallas, Texas area.
The first three routes are host routes since
they indicate how to get to a single host. In the 'netstat'
output this can be seen by the "Genmask" (Subnet Mask) of
255.255.255.255 and the "H" in the Flags column. The remainder
are 'net' routes since they tell the kernel
how to route packets to a subnetwork. The last route is the
default route and the gateway mentioned in that
route is called the default gateway.
When the kernel is trying to send a packet to IP address A, it starts at the top of the routing table and:
A is logically ANDed with the
'Genmask' value in the table entry.
The result is compared with the 'Destination' value in
the table entry.
If the result and the 'Destination' value are the
same, then:
If the 'Gateway' column is non-zero, the packet is
sent to the gateway over the interface named in the
'Iface' column.
Otherwise, the packet is sent directly to A over the interface named in the
'iface' column.
Otherwise, the above steps are repeated on the next entry in
the table.
Since the default route matches any IP address (A LAND 0.0.0.0 = 0.0.0.0), packets that don't
match any of the other routing table entries are sent to the default
gateway which is usually a router at your ISP. Lets take an example.
Suppose that we want to route a packet to 192.168.1.5. That address
clearly doesn't match any of the host routes in the table but if we
logically and that address with 255.255.255.0, the result is 192.168.1.0
which matches this routing table entry:
192.168.1.0 0.0.0.0 255.255.255.0 U 40 0 0 eth2
So to route a packet to 192.168.1.5, the packet is sent directly
over eth2.
One more thing needs to be emphasized -- all outgoing packet are
sent using the routing table and reply packets are not a special case.
There seems to be a common mis-conception whereby people think that
request packets are like salmon and contain a genetic code that is
magically transferred to reply packets so that the replies follow the
reverse route taken by the request. That isn't the case; the replies
may take a totally different route back to the client than was taken by
the requests -- they are totally independent.
Address Resolution Protocol (ARP)
When sending packets over Ethernet, IP addresses aren't used.
Rather Ethernet addressing is based on Media Access Control
(MAC) addresses. Each Ethernet device has it's own unique MAC
address which is burned into a PROM on the device during manufacture.
You can obtain the MAC of an Ethernet device using the 'ip'
utility:
[root@gateway root]# ip addr show eth0
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb qlen 100
link/ether 02:00:08:e3:fa:55 brd ff:ff:ff:ff:ff:ff
inet 206.124.146.176/24 brd 206.124.146.255 scope global eth0
inet 206.124.146.178/24 brd 206.124.146.255 scope global secondary eth0
inet 206.124.146.179/24 brd 206.124.146.255 scope global secondary eth0
[root@gateway root]#
As you can see from the above output, the MAC is 6 bytes (48 bits)
wide. A card's MAC is usually also printed on a label attached to
the card itself. Because IP uses IP addresses and Ethernet uses MAC
addresses, a mechanism is required to translate an IP address into a MAC
address; that is the purpose of the Address Resolution
Protocol (ARP). Here is ARP in action:
[root@gateway root]# tcpdump -nei eth2 arp
tcpdump: listening on eth2
09:56:49.766757 2:0:8:e3:4c:48 0:6:25:aa:8a:f0 arp 42: arp who-has 192.168.1.19 tell 192.168.1.254
09:56:49.769372 0:6:25:aa:8a:f0 2:0:8:e3:4c:48 arp 60: arp reply 192.168.1.19 is-at 0:6:25:aa:8a:f0
2 paquets received by filter
0 paquets dropped by kernel
[root@gateway root]#
In this exchange, 192.168.1.254 (MAC 2:0:8:e3:4c:48) wants to know
the MAC of the device with IP address 192.168.1.19. The system having
that IP address is responding that the MAC address of the device with IP
address 192.168.1.19 is 0:6:25:aa:8a:f0.
In order to avoid having to exchange ARP information each time
that an IP packet is to be sent, systems maintain an
ARP cache of IP<->MAC correspondences. You
can see the ARP cache on your system (including your Windows system)
using the 'arp' command:
[root@gateway root]# arp -na
? (206.124.146.177) at 00:A0:C9:15:39:78 [ether] on eth1
? (192.168.1.3) at 00:A0:CC:63:66:89 [ether] on eth2
? (192.168.1.5) at 00:A0:CC:DB:31:C4 [ether] on eth2
? (206.124.146.254) at 00:03:6C:8A:18:38 [ether] on eth0
? (192.168.1.19) at 00:06:25:AA:8A:F0 [ether] on eth2
The leading question marks are a result of my having specified the
'n' option (Windows 'arp' doesn't allow that option)
which causes the 'arp' program to forego IP->DNS name
translation. Had I not given that option, the question marks would have
been replaced with the FQDN corresponding to each IP address. Notice
that the last entry in the table records the information we saw using
tcpdump above.
RFC 1918
IP addresses are allocated by the Internet Assigned Number Authority
(IANA) who delegates allocations on a geographic basis to Regional
Internet Registries (RIRs). For example, allocation for the Americas and
for sub-Sahara Africa is delegated to the American Registry for Internet Numbers
(ARIN). These RIRs may in turn delegate to national registries. Most of
us don't deal with these registrars but rather get our IP addresses
from our ISP. It's a fact of life that most of us can't afford
as many Public IP addresses as we have devices to assign them to so we
end up making use of Private IP addresses. RFC 1918 reserves several IP
address ranges for this purpose:
10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255
The addresses reserved by RFC 1918 are sometimes referred to as
non-routable because the Internet backbone routers don't forward
packets which have an RFC-1918 destination address. This is
understandable given that anyone can select any of these addresses for
their private use.
When selecting addresses from these ranges, there's a couple
of things to keep in mind:
As the IPv4 address space becomes depleted, more and more
organizations (including ISPs) are beginning to use RFC 1918
addresses in their infrastructure.
You don't want to use addresses that are being used by
your ISP or by another organization with whom you want to establish
a VPN relationship.
So it's a good idea to check with your ISP to see if they are
using (or are planning to use) private addresses before you decide the
addresses that you are going to use.
In this document, external "real"
IP addresses are of the form 192.0.2.x. 192.0.2.0/24 is reserved by
RFC 3330 for use as public IP addresses in printed examples. These
addresses are not to be confused with addresses in 192.168.0.0/16; as
described above, these addresses are reserved by RFC 1918 for private
use.
Setting Up Your Network
The choice of how to set up your network depends primarily on how
many Public IP addresses you have vs. how many addressable entities you
have in your network. Regardless of how many addresses you have, your ISP
will handle that set of addresses in one of two ways:
Routed - Traffic to any of your
addresses will be routed through a single gateway address. This will
generally only be done if your ISP has assigned you a complete subnet
(/29 or larger). In this case, you will assign the gateway address as
the IP address of your firewall/router's external interface.
Non-routed - Your ISP will send
traffic to each of your addresses directly.
In the subsections that follow, we'll look at each of these
separately.
Before we begin, there is one thing for you to check:
If you are using the
Debian package, please check your shorewall.conf file to ensure that the
following are set correctly; if they are not, change them appropriately:
NAT_ENABLED=Yes (Shorewall versions earlier than 1.4.6)
IP_FORWARDING=On
Routed
Let's assume that your ISP has assigned you the subnet
192.0.2.64/28 routed through 192.0.2.65. That means that you have IP
addresses 192.0.2.64 - 192.0.2.79 and that your firewall's external
IP address is 192.0.2.65. Your ISP has also told you that you should use
a netmask of 255.255.255.0 (so your /28 is part of a larger /24). With
this many IP addresses, you are able to subnet your /28 into two
/29's and set up your network as shown in the following diagram.
![]()
Here, the DMZ comprises the subnet 192.0.2.64/29 and the Local
network is 192.0.2.72/29. The default gateway for hosts in the DMZ would
be configured to 192.0.2.66 and the default gateway for hosts in the
local network would be 192.0.2.73.
Notice that this arrangement is rather wasteful of public IP
addresses since it is using 192.0.2.64 and 192.0.2.72 for subnet
addresses, 192.0.2.71 and 192.0.2.79 for subnet broadcast addresses and
192.0.2.66 and 168.0.2.73 for internal addresses on the firewall/router.
Nevertheless, it shows how subnetting can work and if we were dealing
with a /24 rather than a /28 network, the use of 6 IP addresses out of
256 would be justified because of the simplicity of the setup.
The astute reader may have noticed that the Firewall/Router's
external interface is actually part of the DMZ subnet (192.0.2.64/29).
What if DMZ 1 (192.0.2.67) tries to communicate with 192.0.2.65? The
routing table on DMZ 1 will look like this:
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.0.2.64 0.0.0.0 255.255.255.248 U 40 0 0 eth0
0.0.0.0 192.0.2.66 0.0.0.0 UG 40 0 0 eth0
This means that DMZ 1 will send an ARP "who-has
192.0.2.65" request and no device on the DMZ Ethernet segment has
that IP address. Oddly enough, the firewall will respond to the request
with the MAC address of its DMZ Interface!!
DMZ 1 can then send Ethernet frames addressed to that MAC address and
the frames will be received (correctly) by the firewall/router.
It is this rather unexpected ARP behavior on the part of the Linux
Kernel that prompts the warning earlier in this guide regarding the
connecting of multiple firewall/router interfaces to the same hub or
switch. When an ARP request for one of the firewall/router's IP
addresses is sent by another system connected to the hub/switch, all of
the firewall's interfaces that connect to the hub/switch can
respond! It is then a race as to which "here-is" response
reaches the sender first.
Non-routed
If you have the above situation but it is non-routed, you can
configure your network exactly as described above with one additional
twist; simply specify the "proxyarp" option on all three
firewall interfaces in the /etc/shorewall/interfaces file.
Most of us don't have the luxury of having enough public IP
addresses to set up our networks as shown in the preceding example (even
if the setup is routed).
For the remainder of this section, assume
that your ISP has assigned you IP addresses 192.0.2.176-180 and has told
you to use netmask 255.255.255.0 and default gateway 192.0.2.254.
Clearly, that set of addresses doesn't comprise a subnetwork
and there aren't enough addresses for all of the network interfaces.
There are four different techniques that can be used to work around this
problem.
Source Network Address Translation
(SNAT).
Destination Network Address Translation
(DNAT) also known as Port Forwarding.
Proxy ARP.
Network Address Translation (NAT) also
referred to as One-to-one NAT.
Often a combination of these techniques is used. Each of these
will be discussed in the sections that follow.
SNAT
With SNAT, an internal LAN segment is configured using RFC 1918
addresses. When a host A on this
internal segment initiates a connection to host B
on the internet, the firewall/router rewrites the IP header in the
request to use one of your public IP addresses as the source address.
When B responds and the response is
received by the firewall, the firewall changes the destination address
back to the RFC 1918 address of A and
forwards the response back to A.
Let's suppose that you decide to use SNAT on your local zone
and use public address 192.0.2.176 as both your firewall's
external IP address and the source IP address of internet requests
sent from that zone.
![]()
The local zone has been subnetted as 192.168.201.0/29 (netmask
255.255.255.248).
The systems
in the local zone would be configured with a default gateway of
192.168.201.1 (the IP address of the firewall's local
interface).
SNAT is
configured in Shorewall using the /etc/shorewall/masq file.
INTERFACE
SUBNET
ADDRESS
eth0
192.168.201.0/29
192.0.2.176
This example used the normal technique of assigning the same
public IP address for the firewall external interface and for SNAT. If
you wanted to use a different IP address, you would either have to use
your distributions network configuration tools to add that IP address
to the external interface or you could set ADD_SNAT_ALIASES=Yes in
/etc/shorewall/shorewall.conf and Shorewall will add the address for
you.
DNAT
When SNAT is used, it is impossible for hosts on the internet to
initiate a connection to one of the internal systems since those
systems do not have a public IP address. DNAT provides a way to allow
selected connections from the internet.
Suppose that
your daughter wants to run a web server on her system "Local
3". You could allow connections to the internet to her server by
adding the following entry in /etc/shorewall/rules:
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
SOURCE PORT(S)
ORIGINAL DEST
DNAT
net
loc:192.168.201.4
tcp
www
-
192.0.2.176
If one of your daughter's friends at address A wants to access your daughter's server,
she can connect to http://192.0.2.176 (the firewall's external IP
address) and the firewall will rewrite the destination IP address to
192.168.201.4 (your daughter's system) and forward the request.
When your daughter's server responds, the firewall will rewrite
the source address back to 192.0.2.176 and send the response back to
A.
This example used the firewall's external IP address for
DNAT. You can use another of your public IP addresses but Shorewall
will not add that address to the firewall's external interface for
you.
Proxy ARP
The idea behind Proxy ARP is that:
A host H behind your
firewall is assigned one of your public IP addresses (A), and is assigned the same netmask (M) as the firewall's external
interface.
The firewall responds to ARP "who has" requests for
A.
When H A andissues an ARP "who has"
request for an address in the subnetwork defined by M, the firewall will respond (with the MAC
if the firewall interface) to H.
Let us suppose that we decide to use Proxy ARP on the DMZ in our
example network.
![]()
Here, we've assigned the IP addresses 192.0.2.177 to system
DMZ 1 and 192.0.2.178 to DMZ 2. Notice that we've just assigned an
arbitrary RFC 1918 IP address and subnet mask to the DMZ interface on
the firewall. That address and netmask isn't relevant - just be
sure it doesn't overlap another subnet that you've defined.
The Shorewall
configuration of Proxy ARP is done using the/etc/shorewall/proxyarp
file.
ADDRESS
EXTERNAL
INTERFACE
HAVE ROUTE
192.0.2.177
eth2
eth0
No
192.0.2.178
eth2
eth0
No
Because the HAVE ROUTE column contains No, Shorewall will add
host routes thru eth2 to 192.0.2.177 and 192.0.2.178. The ethernet
interfaces on DMZ 1 and DMZ 2 should be configured to have the IP
addresses shown but should have the same default gateway as the
firewall itself -- namely 192.0.2.254. In other words, they should be
configured just like they would be if they were parallel to the
firewall rather than behind it.
Do not add the Proxy ARP'ed
address(es) (192.0.2.177 and 192.0.2.178 in the above example) to
the external interface (eth0 in this example) of the firewall.
A word of warning is in order here. ISPs typically configure
their routers with a long ARP cache timeout. If you move a system from
parallel to your firewall to behind your firewall with Proxy ARP, it
will probably be HOURS before that system can communicate with the
internet. There are a couple of things that you can try:
(Courtesy of Bradey Honsinger) A reading of Stevens'
TCP/IP Illustrated, Vol 1 reveals that a
"gratuitous" ARP packet should cause the ISP's
router to refresh their ARP cache (section 4.7). A gratuitous
ARP is simply a host requesting the MAC address for its own IP;
in addition to ensuring that the IP address isn't a
duplicate,...
"if the host sending the gratuitous ARP has just
changed its hardware address..., this packet causes any other
host...that has an entry in its cache for the old hardware
address to update its ARP cache entry accordingly."
Which is, of course, exactly what you want to do when you
switch a host from being exposed to the Internet to behind
Shorewall using proxy ARP (or one-to-one NAT for that matter).
Happily enough, recent versions of Redhat's iputils package
include "arping", whose "-U" flag does just that:
arping -U -I <net if> <newly proxied IP>
arping -U -I eth0 66.58.99.83 # for exampleStevens
goes on to mention that not all systems respond correctly to
gratuitous ARPs, but googling for "arping -U" seems to
support the idea that it works most of the time.
You can call your ISP and ask them to purge the stale ARP
cache entry but many either can't or won't purge
individual entries.
You can determine if your ISP's gateway ARP cache is stale
using ping and tcpdump. Suppose that we suspect that the gateway
router has a stale ARP cache entry for 192.0.2.177. On the firewall,
run tcpdump as follows:
tcpdump -nei eth0 icmp
Now from 192.0.2.177, ping the ISP's gateway (which we will
assume is 192.0.2.254):
ping 192.0.2.254
We can now observe the tcpdump output:
13:35:12.159321 0:4:e2:20:20:33 0:0:77:95:dd:19 ip 98: 192.0.2.177 > 192.0.2.254: icmp: echo request (DF)
13:35:12.207615 0:0:77:95:dd:19 0:c0:a8:50:b2:57 ip 98: 192.0.2.254 > 192.0.2.177 : icmp: echo replyNotice
that the source MAC address in the echo request is different from the
destination MAC address in the echo reply!! In this case
0:4:e2:20:20:33 was the MAC of the firewall's eth0 NIC while
0:c0:a8:50:b2:57 was the MAC address of DMZ 1. In other words, the
gateway's ARP cache still associates 192.0.2.177 with the NIC in
DMZ 1 rather than with the firewall's eth0.
One-to-one NAT
With one-to-one NAT, you assign local systems RFC 1918 addresses
then establish a one-to-one mapping between those addresses and public
IP addresses. For outgoing connections SNAT (Source Network Address
Translation) occurs and on incoming connections DNAT (Destination
Network Address Translation) occurs. Let's go back to our earlier
example involving your daughter's web server running on system
Local 3.
![]()
Recall that in this setup, the local network is using SNAT and
is sharing the firewall external IP (192.0.2.176) for outbound
connections. This is done with the following entry in
/etc/shorewall/masq:
INTERFACE
SUBNET
ADDRESS
eth0
192.168.201.0/29
192.0.2.176
Suppose now that
you have decided to give your daughter her own IP address
(192.0.2.179) for both inbound and outbound connections. You would do
that by adding an entry in /etc/shorewall/nat.
EXTERNAL
INTERFACE
INTERNAL
ALL INTERFACES
LOCAL
192.0.2.179
eth0
192.168.201.4
No
No
With this entry in place, you daughter has her own IP address
and the other two local systems share the firewall's IP address.
Once the
relationship between 192.0.2.179 and 192.168.201.4 is established by
the nat file entry above, it is no longer appropriate to use a DNAT
rule for you daughter's web server -- you would rather just use an
ACCEPT rule:
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
SOURCE PORT(S)
ORIGINAL DEST
ACCEPT
net
loc:192.168.201.4
tcp
www
A word of warning is in order here. ISPs typically configure
their routers with a long ARP cache timeout. If you move a system from
parallel to your firewall to behind your firewall with one-to-one NAT,
it will probably be HOURS before that system can communicate with the
internet. There are a couple of things that you can try:
(Courtesy of Bradey Honsinger) A reading of Stevens'
TCP/IP Illustrated, Vol 1 reveals that a
"gratuitous" ARP packet should cause the ISP's
router to refresh their ARP cache (section 4.7). A gratuitous
ARP is simply a host requesting the MAC address for its own IP;
in addition to ensuring that the IP address isn't a
duplicate,...
"if the host sending the gratuitous ARP has just
changed its hardware address..., this packet causes any other
host...that has an entry in its cache for the old hardware
address to update its ARP cache entry accordingly."
Which is, of course, exactly what you want to do when you
switch a host from being exposed to the Internet to behind
Shorewall using one-to-one NAT. Happily enough, recent versions of
Redhat's iputils package include "arping", whose
"-U" flag does just that:
arping -U -I <net if> <newly proxied IP>
arping -U -I eth0 66.58.99.83 # for exampleStevens
goes on to mention that not all systems respond correctly to
gratuitous ARPs, but googling for "arping -U" seems to
support the idea that it works most of the time.
You can call your ISP and ask them to purge the stale ARP
cache entry but many either can't or won't purge
individual entries.
You can determine if your ISP's gateway ARP cache is stale
using ping and tcpdump. Suppose that we suspect that the gateway
router has a stale ARP cache entry for 192.0.2.177. On the firewall,
run tcpdump as follows:
tcpdump -nei eth0 icmp
Now from 192.0.2.177, ping the ISP's gateway (which we will
assume is 192.0.2.254):
ping 192.0.2.254
We can now observe the tcpdump output:
13:35:12.159321 0:4:e2:20:20:33 0:0:77:95:dd:19 ip 98: 192.0.2.177 > 192.0.2.254: icmp: echo request (DF)
13:35:12.207615 0:0:77:95:dd:19 0:c0:a8:50:b2:57 ip 98: 192.0.2.254 > 192.0.2.177 : icmp: echo replyNotice
that the source MAC address in the echo request is different from the
destination MAC address in the echo reply!! In this case
0:4:e2:20:20:33 was the MAC of the firewall's eth0 NIC while
0:c0:a8:50:b2:57 was the MAC address of DMZ 1. In other words, the
gateway's ARP cache still associates 192.0.2.177 with the NIC in
DMZ 1 rather than with the firewall's eth0.
Rules
With the default
policies, your local systems (Local 1-3) can access any servers on the
internet and the DMZ can't access any other host (including the
firewall). With the exception of DNAT rules which cause address
translation and allow the translated connection request to pass through
the firewall, the way to allow connection requests through your firewall
is to use ACCEPT rules.
Since the SOURCE PORT and ORIG. DEST. Columns aren't used in
this section, they won't be shown
You probably want to allow ping between your zones:
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
ACCEPT
net
dmz
icmp
echo-request
ACCEPT
net
loc
icmp
echo-request
ACCEPT
dmz
loc
icmp
echo-request
ACCEPT
loc
dmz
icmp
echo-request
Let's suppose that you run mail and pop3 servers on DMZ 2 and
a Web Server on DMZ 1. The rules that you would need are:
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
COMMENTS
ACCEPT
net
dmz:192.0.2.178
tcp
smtp
# Mail from the Internet
ACCEPT
net
dmz:192.0.2.178
tcp
pop3
# Pop3 from the Internet
ACCEPT
loc
dmz:192.0.2.178
tcp
smtp
# Mail from the Local Network
ACCEPT
loc
dmz:192.0.2.178
tcp
pop3
# Pop3 from the Local Network
ACCEPT
fw
dmz:192.0.2.178
tcp
smtp
# Mail from the firewall
ACCEPT
dmz:192.0.2.178
net
tcp
smtp
# Mails to Internet
ACCEPT
net
dmz:192.0.2.177
tcp
http
# WWW from the Internet
ACCEPT
net
dmz:192.0.2.177
tcp
https
# Secure HTTP from the Internet
ACCEPT
loc
dmz:192.0.2.177
htp
https
# Secure HTTP from the Local Network
If you run a public DNS server on 192.0.2.177, you would need to
add the following rules:
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
COMMENTS
ACCEPT
net
dmz:192.0.2.177
udp
domain
# UDP DNS from the Internet
ACCEPT
net
dmz:192.0.2.177
tcp
domain
# TCP DNS from the Internet
ACCEPT
fw
dmz:192.0.2.177
udp
domain
# UDP DNS from the firewall
ACCEPT
fw
dmz:192.0.2.177
tcp
domain
# TCP DNS from the firewall
ACCEPT
loc
dmz:192.0.2.177
udp
domain
# UDP DNS from the Local Network
ACCEPT
loc
dmz:192.0.2.177
tcp
domain
# TCP DNS from the Local Network
ACCEPT
dmz:192.0.2.177
net
udp
domain
# UDP DNS to the Internet
ACCEPT
dmz:192.0.2.177
net
tcp
domain
# TCP DNS to the Internet
You probably want some way to communicate with your firewall and
DMZ systems from the local network -- I recommend SSH which through its
scp utility can also do publishing and software update distribution.
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
COMMENTS
ACCEPT
loc
dmz
tcp
ssh
# SSH to the DMZ
ACCEPT
loc
fw
tcp
ssh
# SSH to the firewall
Odds and Ends
The above discussion reflects my personal preference for using
Proxy ARP for my servers in my DMZ and SNAT/NAT for my local systems. I
prefer to use NAT only in cases where a system that is part of an RFC
1918 subnet needs to have it's own public IP.
If you haven't
already, it would be a good idea to browse through /etc/shorewall/shorewall.conf
just to see if there is anything there that might be of interest. You
might also want to look at the other configuration files that you
haven't touched yet just to get a feel for the other things that
Shorewall can do.
In case you haven't been keeping score, here's the final
set of configuration files for our sample network. Only those that were
modified from the original installation are shown.
/etc/shorewall/interfaces (The "options" will be very
site-specific).
ZONE
INTERFACE
BROADCAST
OPTIONS
net
eth0
detect
norfc1918,routefilter
loc
eth1
detect
dmz
eth2
detect
The setup described here requires that your network interfaces be
brought up before Shorewall can start. This opens a short window during
which you have no firewall protection. If you replace 'detect'
with the actual broadcast addresses in the entries above, you can bring
up Shorewall before you bring up your network interfaces.
ZONE
INTERFACE
BROADCAST
OPTIONS
net
eth0
192.0.2.255
norfc1918,routefilter
loc
eth1
192.168.201.7
dmz
eth2
192.168.202.7
/etc/shorewall/masq - Local Subnet
INTERFACE
SUBNET
ADDRESS
eth0
192.168.201.0/29
192.0.2.176
/etc/shorewall/proxyarp - DMZ
ADDRESS
EXTERNAL
INTERFACE
HAVE ROUTE
192.0.2.177
eth2
eth0
No
192.0.2.178
eth2
eth0
No
/etc/shorewall/nat- Daughter's System
EXTERNAL
INTERFACE
INTERNAL
ALL INTERFACES
LOCAL
192.0.2.179
eth0
192.168.201.4
No
No
/etc/shorewall/rules
ACTION
SOURCE
DESTINATION
PROTOCOL
PORT(S)
COMMENTS
ACCEPT
net
dmz:192.0.2.178
tcp
smtp
# Mail from the Internet
ACCEPT
net
dmz:192.0.2.178
tcp
pop3
# Pop3 from the Internet
ACCEPT
loc
dmz:192.0.2.178
tcp
smtp
# Mail from the Local Network
ACCEPT
loc
dmz:192.0.2.178
tcp
pop3
# Pop3 from the Local network
ACCEPT
fw
dmz:192.0.2.178
tcp
smtp
# Mail from the firewall
ACCEPT
dmz:192.0.2.178
net
tcp
smtp
# Mails to Internet
ACCEPT
net
dmz:192.0.2.177
tcp
http
# WWW from the Net
ACCEPT
net
dmz:192.0.2.177
tcp
https
# Secure HTTP from the Net
ACCEPT
loc
dmz:192.0.2.177
htp
https
# Secure HTTP from the Local Network
ACCEPT
net
dmz:192.0.2.177
udp
domain
# UDP DNS from the Internet
ACCEPT
net
dmz:192.0.2.177
tcp
domain
# TCP DNS from the Internet
ACCEPT
fw
dmz:192.0.2.177
udp
domain
# UDP DNS from the firewall
ACCEPT
fw
dmz:192.0.2.177
tcp
domain
# TCP DNS depuis le firewall
ACCEPT
loc
dmz:192.0.2.177
udp
domain
# UDP DNS depuis le Réseau Local
ACCEPT
loc
dmz:192.0.2.177
tcp
domain
# TCP DNS from the Local Network
ACCEPT
dmz:192.0.2.177
net
udp
domain
# UDP DNS to the Internet
ACCEPT
dmz:192.0.2.177
net
tcp
domain
# TCP DNS to the Internet
ACCEPT
net
dmz
icmp
echo-request
Ping
ACCEPT
dmz
net
icmp
echo-request
"
ACCEPT
dmz
loc
icmp
echo-request
"
ACCEPT
loc
dmz
icmp
echo-request
"
ACCEPT
loc
dmz
tcp
ssh
# SSH to the DMZ
ACCEPT
loc
fw
tcp
ssh
# SSH to the firewall
DNS
Given the collection of RFC 1918 and public addresses in this setup,
it only makes sense to have separate internal and external DNS servers.
You can combine the two into a single BIND 9 server using Views. If you
are not interested in Bind 9 views, you can go to the next section.
Suppose that your domain is foobar.net and you want the two DMZ
systems named www.foobar.net and mail.foobar.net and you want the three
local systems named "winken.foobar.net, blinken.foobar.net and
nod.foobar.net. You want your firewall to be known as firewall.foobar.net
externally and it's interface to the local network to be know as
gateway.foobar.net and its interface to the dmz as dmz.foobar.net.
Let's have the DNS server on 192.0.2.177 which will also be known by
the name ns1.foobar.net.
The /etc/named.conf file would look like this:
options {
directory "/var/named";
listen-on { 127.0.0.1 ; 192.0.2.177; };
};
logging {
channel xfer-log {
file "/var/log/named/bind-xfer.log";
print-category yes;
print-severity yes;
print-time yes;
severity info;
};
category xfer-in { xfer-log; };
category xfer-out { xfer-log; };
category notify { xfer-log; };
};
#
# This is the view presented to our internal systems
#
view "internal" {
#
# These are the clients that see this view
#
match-clients { 192.168.201.0/29;
192.168.202.0/29;
127.0.0.0/8;
192.0.2.176/32;
192.0.2.178/32;
192.0.2.179/32;
192.0.2.180/32; };
#
# If this server can't complete the request, it should use outside
# servers to do so
#
recursion yes;
zone "." in {
type hint;
file "int/root.cache";
};
zone "foobar.net" in {
type master;
notify no;
allow-update { none; };
file "int/db.foobar";
};
zone "0.0.127.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "int/db.127.0.0";
};
zone "201.168.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "int/db.192.168.201";
};
zone "202.168.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "int/db.192.168.202";
};
zone "176.2.0.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "db.192.0.2.176";
};
zone "177.2.0.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "db.192.0.2.177";
};
zone "178.2.0.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "db.192.0.2.178";
};
zone "179.2.0.192.in-addr.arpa" in {
type master;
notify no;
allow-update { none; };
file "db.206.124.146.179";
};
};
#
# This is the view that we present to the outside world
#
view "external" {
match-clients { any; };
#
# If we can't answer the query, we tell the client so
#
recursion no;
zone "foobar.net" in {
type master;
notify yes;
allow-update {none; };
allow-transfer { <secondary NS IP>; };
file "ext/db.foobar";
};
zone "176.2.0.192.in-addr.arpa" in {
type master;
notify yes;
allow-update { none; };
allow-transfer { <secondary NS IP>; };
file "db.192.0.2.176";
};
zone "177.2.0.192.in-addr.arpa" in {
type master;
notify yes;
allow-update { none; };
allow-transfer { <secondary NS IP>; };
file "db.192.0.2.177";
};
zone "178.2.0.192.in-addr.arpa" in {
type master;
notify yes;
allow-update { none; };
allow-transfer { <secondary NS IP>; };
file "db.192.0.2.178";
};
zone "179.2.0.192.in-addr.arpa" in {
type master;
notify yes;
allow-update { none; };
allow-transfer { <secondary NS IP>; };
file "db.192.0.2.179";
};
};
Here are the files in /var/named (those not shown are usually
included in your bind disbribution).
db.192.0.2.176 - This is the reverse zone for the firewall's
external interface
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.0.2.176/32
; Filename: db.192.0.2.176
; ############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2001102303 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
;
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
@ 604800 IN NS <name of secondary ns>.
;
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
176.2.0.192.in-addr.arpa. 86400 IN PTR firewall.foobar.net.
db.192.0.2.177 - Reverse zone www/DNS server
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.0.2.177/32
; Filename: db.192.0.2.177
; ############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2001102303 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
;
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
@ 604800 IN NS <name of secondary ns>.
;
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
177.2.0.192.in-addr.arpa. 86400 IN PTR www.foobar.net.
db.192.0.2.178 - Reverse zone for the mail server
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.0.2.178/32
; Filename: db.192.0.2.178
; ############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2001102303 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
;
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
@ 604800 IN NS <name of secondary ns>.
;
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
178.2.0.192.in-addr.arpa. 86400 IN PTR mail.foobar.net.
db.192.0.2.179 - Reverse zone for Daughter's public web server
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.0.2.179/32
; Filename: db.192.0.2.179
; ############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2001102303 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
;
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
@ 604800 IN NS <name of secondary ns>.
;
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
179.2.0.192.in-addr.arpa. 86400 IN PTR nod.foobar.net.
int/db.127.0.0 - Reverse zone for localhost
; ############################################################
; Start of Authority (Inverse Address Arpa) for 127.0.0.0/8
; Filename: db.127.0.0
; ############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2001092901 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
1 86400 IN PTR localhost.foobar.net.
int/db.192.168.201 - Reverse zone for the local network. This is
only shown to internal clients.
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.168.201.0/29
; Filename: db.192.168.201
; ############################################################
@ 604800 IN SOA ns1.foobar.net netadmin.foobar.net. (
2002032501 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
1 86400 IN PTR gateway.foobar.net.
2 86400 IN PTR winken.foobar.net.
3 86400 IN PTR blinken.foobar.net.
4 86400 IN PTR nod.foobar.net.
int/db.192.168.202 - Reverse zone for the firewall's DMZ
Interface
; ############################################################
; Start of Authority (Inverse Address Arpa) for 192.168.202.0/29
; Filename: db.192.168.202
; ############################################################
@ 604800 IN SOA ns1.foobar.net netadmin.foobar.net. (
2002032501 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ) ; minimum (1 day)
; ############################################################
; Specify Name Servers for all Reverse Lookups (IN-ADDR.ARPA)
; ############################################################
@ 604800 IN NS ns1.foobar.net.
; ############################################################
; Iverse Address Arpa Records (PTR's)
; ############################################################
1 86400 IN PTR dmz.foobar.net.
int/db.foobar - Forward zone for internal clients.
;##############################################################
; Start of Authority for foobar.net.
; Filename: db.foobar
;##############################################################
@ 604800 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2002071501 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ); minimum (1 day)
;############################################################
; foobar.net Nameserver Records (NS)
;############################################################
@ 604800 IN NS ns1.foobar.net.
;############################################################
; Foobar.net Office Records (ADDRESS)
;############################################################
localhost 86400 IN A 127.0.0.1
firewall 86400 IN A 192.0.2.176
www 86400 IN A 192.0.2.177
ns1 86400 IN A 192.0.2.177
www 86400 IN A 192.0.2.177
gateway 86400 IN A 192.168.201.1
winken 86400 IN A 192.168.201.2
blinken 86400 IN A 192.168.201.3
nod 86400 IN A 192.168.201.4
ext/db.foobar - Forward zone for external clients.
;##############################################################
; Start of Authority for foobar.net.
; Filename: db.foobar
;##############################################################
@ 86400 IN SOA ns1.foobar.net. netadmin.foobar.net. (
2002052901 ; serial
10800 ; refresh (3 hour)
3600 ; retry (1 hour)
604800 ; expire (7 days)
86400 ); minimum (1 day)
;############################################################
; Foobar.net Nameserver Records (NS)
;############################################################
@ 86400 IN NS ns1.foobar.net.
@ 86400 IN NS <secondary NS>.
;############################################################
; Foobar.net Foobar Wa Office Records (ADDRESS)
;############################################################
localhost 86400 IN A 127.0.0.1
;
; The firewall itself
;
firewall 86400 IN A 192.0.2.176
;
; The DMZ
;
ns1 86400 IN A 192.0.2.177
www 86400 IN A 192.0.2.177
mail 86400 IN A 192.0.2.178
;
; The Local Network
;
nod 86400 IN A 192.0.2.179
;############################################################
; Current Aliases for foobar.net (CNAME)
;############################################################
;############################################################
; foobar.net MX Records (MAIL EXCHANGER)
;############################################################
foobar.net. 86400 IN A 192.0.2.177
86400 IN MX 0 mail.foobar.net.
86400 IN MX 1 <backup MX>.
Starting and Stopping the Firewall
The Installation procedure
configures your system to start Shorewall at system boot.
The firewall is started using the "shorewall start" command
and stopped using "shorewall stop". When the firewall is stopped,
routing is enabled on those hosts that have an entry in /etc/shorewall/routestopped.
A running firewall may be restarted using the "shorewall restart"
command. If you want to totally remove any trace of Shorewall from your
Netfilter configuration, use "shorewall clear".
Edit the /etc/shorewall/routestopped
file and configure those systems that you want to be able to access the
firewall when it is stopped.
If you are connected to your firewall from the internet, do not
issue a "shorewall stop" command unless you have added an entry
for the IP address that you are connected from to /etc/shorewall/routestopped.
Also, I don't recommend using "shorewall restart"; it is
better to create an an
alternate configuration and test it using the
"shorewall try"
command.