shorewall6-masq 5 Configuration Files masq Shorewall6 Masquerade/SNAT definition file /etc/shorewall6/masq Use this file to define Source NAT (SNAT). Requires Shorewall 4.5.14 or later. The entries in this file are order-sensitive. The first entry that matches a particular connection will be the one that is used. If you have more than one ISP link, adding entries to this file will not force connections to go out through a particular link. You must use entries in shorewall6-rtrules(5) or PREROUTING entries in shorewall-tcrules(5) to do that. The columns in the file are as follows. INTERFACE:DEST - {[+]interfacelist|[:[dest-address[,dest-address]...[exclusion]]|?COMMENT} Outgoing interfacelist. This may be a comma-separated list of interface names. This is usually your internet interface. Each interface must match an entry in shorewall6-interfaces(5). Shorewall allows loose matches to wildcard entries in shorewall6-interfaces(5). For example, ppp0 in this file will match a shorewall6-interfaces(5) entry that defines ppp+. Where more that one internet provider share a single interface, the provider is specified by including the provider name or number in parentheses: eth0(Avvanta) In that case, you will want to specify the interface's address for that provider in the ADDRESS column. The interface may be qualified by adding the character ":" followed by a comma-separated list of destination host or subnet addresses to indicate that you only want to change the source IP address for packets being sent to those particular destinations. Exclusion is allowed (see shorewall6-exclusion(5)) as are ipset names preceded by a plus sign '+'. Comments may be attached to Netfilter rules generated from entries in this file through the use of ?COMMENT lines. These lines begin with ?COMMENT; the remainder of the line is treated as a comment which is attached to subsequent rules until another ?COMMENT line is found or until the end of the file is reached. To stop adding comments to rules, use a line containing only ?COMMENT. Beginning with Shorewall 4.6.0, a new syntax is also accepted. With the exception of the leading '+', the interfacelist and qualifiers may appear within the parentheses of INLINE(...). Example: +INLINE(eth0) When this is done, you may augment the rule generated by Shorewall with iptables matches of your own. These matches appear after a semicolon (';') at the end of the line. See example 2 below. SOURCE (Optional) - [interface|address[,address][exclusion]] Set of hosts that you wish to SNAT; one or more host or network addresses separated by comma. You may use ipset names preceded by a plus sign (+) to specify a set of hosts. ADDRESS (Optional) - [-|NONAT|[address-or-address-range[,address-or-address-range]...][:lowport-highport][:random][:persistent]|detect|random] If you do not specify an address or address range, masquerading will be performed. This requires Masquerade Target support in your kernel and ip6tables. If you specify an address here, SNAT will be used and this will be the source address. You may also specify a range of up to 256 IP addresses if you want the SNAT address to be assigned from that range in a round-robin fashion by connection. The range is specified by first.ip.in.range-last.ip.in.range. You may follow the port range with:random in which case assignment of ports from the list will be random. random may also be specified by itself in this column in which case random local port assignments are made for the outgoing connections. Example: [2001:470:a:227::2]-[2001:470:a:227::10]:1000-1010 You may follow the port range (or :random) with :persistent. This is only useful when an address range is specified and causes a client to be given the same source/destination IP pair. This column may not contain DNS Names. Normally, Netfilter will attempt to retain the source port number. You may cause netfilter to remap the source port by following an address or range (if any) by ":" and a port range with the format lowport-highport. If this is done, you must specify "tcp" or "udp" in the PROTO column. Examples: [2001:470:a:787::2]:5000-6000 If you simply place NONAT in this column, no rewriting of the source IP address or port number will be performed. This is useful if you want particular traffic to be exempt from the entries that follow in the file. PROTO (Optional) - {-|[!]{protocol-name|protocol-number}[,...]|+ipset} If you wish to restrict this entry to a particular protocol then enter the protocol name (from protocols(5)) or number here. Beginning with Shorewall 4.5.12, this column can accept a comma-separated list of protocols. Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is intended to be used with bitmap:port ipsets. PORT(S) (Optional) - {-|[!]port-name-or-number[,port-name-or-number]...|+ipset} If the PROTO column specifies TCP (6), UDP (17), DCCP (33), SCTP (132) or UDPLITE (136) then you may list one or more port numbers (or names from services(5)) or port ranges separated by commas. Port ranges are of the form lowport:highport. Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is intended to be used with bitmap:port ipsets. IPSEC (Optional) - [option[,option]...] If you specify a value other than "-" in this column, you must be running kernel 2.6 and your kernel and iptables must include policy match support. Comma-separated list of options from the following. Only packets that will be encrypted via an SA that matches these options will have their source address changed. reqid=number where number is specified using setkey(8) using the 'unique:number option for the SPD level. spi=<number> where number is the SPI of the SA used to encrypt/decrypt packets. proto=ah|esp|ipcomp IPSEC Encapsulation Protocol mss=number sets the MSS field in TCP packets mode=transport|tunnel IPSEC mode tunnel-src=address[/mask] only available with mode=tunnel tunnel-dst=address[/mask] only available with mode=tunnel strict Means that packets must match all rules. next Separates rules; can only be used with strict yes When used by itself, causes all traffic that will be encrypted/encapsulated to match the rule. MARK - [!]value[/mask][:C] Defines a test on the existing packet or connection mark. The rule will match only if the test returns true. If you don't want to define a test but need to specify anything in the following columns, place a "-" in this field. ! Inverts the test (not equal) value Value of the packet or connection mark. mask A mask to be applied to the mark before testing. :C Designates a connection mark. If omitted, the packet mark's value is tested. USER/GROUP (Optional) - [!][user-name-or-number][:group-name-or-number][+program-name] Only locally-generated connections will match if this column is non-empty. When this column is non-empty, the rule matches only if the program generating the output is running under the effective user and/or group specified (or is NOT running under that id if "!" is given). Examples: joe program must be run by joe :kids program must be run by a member of the 'kids' group !:kids program must not be run by a member of the 'kids' group +upnpd #program named upnpd The ability to specify a program name was removed from Netfilter in kernel version 2.6.14. SWITCH - [!]switch-name[={0|1}] Added in Shorewall 4.5.1 and allows enabling and disabling the rule without requiring shorewall restart. The rule is enabled if the value stored in /proc/net/nf_condition/switch-name is 1. The rule is disabled if that file contains 0 (the default). If '!' is supplied, the test is inverted such that the rule is enabled if the file contains 0. Within the switch-name, '@0' and '@{0}' are replaced by the name of the chain to which the rule is a added. The switch-name (after '@...' expansion) must begin with a letter and be composed of letters, decimal digits, underscores or hyphens. Switch names must be 30 characters or less in length. Switches are normally off. To turn a switch on: echo 1 > /proc/net/nf_condition/switch-name To turn it off again: echo 0 > /proc/net/nf_condition/switch-name Switch settings are retained over shorewall restart. Beginning with Shorewall 4.5.10, when the switch-name is followed by =0 or =1, then the switch is initialized to off or on respectively by the start command. Other commands do not affect the switch setting. ORIGINAL DEST (origdest) - [-|address[,address]...[exclusion]|exclusion] (Optional) This column may be included and may contain one or more addresses (host or network) separated by commas. Address ranges are not allowed. When this column is supplied, rules are generated that require that the original destination address matches one of the listed addresses. It is useful for specifying that SNAT should occur only for connections that were acted on by a DNAT when they entered the firewall. PROBABILITY - [probability] Added in Shorewall 5.0.0. When non-empty, requires the Statistics Match capability in your kernel and ip6tables and causes the rule to match randomly but with the given probability. The probability is a number 0 < probability <= 1 and may be expressed at up to 8 decimal points of precision. Example 1: You have a simple 'masquerading' setup where eth0 connects to a DSL or cable modem and eth1 connects to your local network with subnet 2001:470:b:787::0/64 Your entry in the file will be: #INTERFACE SOURCE ADDRESS eth0 2001:470:b:787::0/64 - Example 2: Your sit1 interface has two public IP addresses: 2001:470:a:227::1 and 2001:470:b:227::1. You want to use the iptables statistics match to masquerade outgoing connections evenly between these two addresses. /etc/shorewall/masq: #INTERFACE SOURCE ADDRESS INLINE(sit1) 0.0.0.0/0 2001:470:a:227::1 ; -m statistic --mode random --probability 0.50 sit1 0.0.0.0/0 2001:470:a:227::2 If INLINE_MATCHES=Yes in shorewall6.conf(5), then these rules may be specified as follows: /etc/shorewall/masq: #INTERFACE SOURCE ADDRESS sit1 0.0.0.0/0 2001:470:a:227::1 ; -m statistic --mode random --probability 0.50 sit1 0.0.0.0/0 2001:470:a:227::2 /etc/shorewall6/masq