shorewall-blacklist 5 blacklist Shorewall Blacklist file /etc/shorewall/blacklist The blacklist file is used to perform static blacklisting. You can blacklist by source address (IP or MAC), or by application. The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in the alternate specification syntax). ADDRESS/SUBNET (networks) - {-|~mac-address|ip-address|address-range|+ipset} Host address, network address, MAC address, IP address range (if your kernel and iptables contain iprange match support) or ipset name prefaced by "+" (if your kernel supports ipset match). Exclusion (shorewall-exclusion(5)) is supported. MAC addresses must be prefixed with "~" and use "-" as a separator. Example: ~00-A0-C9-15-39-78 A dash ("-") in this column means that any source address will match. This is useful if you want to blacklist a particular application using entries in the PROTOCOL and PORTS columns. PROTOCOL (proto) - {-|[!]protocol-number|[!]protocol-name} Optional - If specified, must be a protocol number or a protocol name from protocols(5). PORTS - {-|[!]port-name-or-number[,port-name-or-number]...} Optional - may only be specified if the protocol is TCP (6) or UDP (17). A comma-separated list of destination port numbers or service names from services(5). OPTIONS - {-|{dst|src|whitelist|audit}[,...]} Optional - added in 4.4.12. If specified, indicates whether traffic from ADDRESS/SUBNET (src) or traffic to ADDRESS/SUBNET (dst) should be blacklisted. The default is src. If the ADDRESS/SUBNET column is empty, then this column has no effect on the generated rule. In Shorewall 4.4.12, the keywords from and to were used in place of src and dst respectively. Blacklisting was still restricted to traffic arriving on an interface that has the 'blacklist' option set. So to block traffic from your local network to an internet host, you had to specify blacklist on your internal interface in shorewall-interfaces (5). Beginning with Shorewall 4.4.13, entries are applied based on the blacklist setting in shorewall-zones(5): 'blacklist' in the OPTIONS or IN_OPTIONS column. Traffic from this zone is passed against the entries in this file that have the src option (specified or defaulted). 'blacklist' in the OPTIONS or OUT_OPTIONS column. Traffic to this zone is passed against the entries in this file that have the dst option. In Shorewall 4.4.20, the whitelist option was added. When whitelist is specified, packets/connections that match the entry are not matched against the remaining entries in the file. The audit option was also added in 4.4.20 and causes packets matching the entry to be audited. The audit option may not be specified in whitelist entries and require AUDIT_TARGET support in the kernel and iptables. Example 1: To block DNS queries from address 192.0.2.126: #ADDRESS/SUBNET PROTOCOL PORT 192.0.2.126 udp 53 Example 2: To block some of the nuisance applications: #ADDRESS/SUBNET PROTOCOL PORT - udp 1024:1033,1434 - tcp 57,1433,1434,2401,2745,3127,3306,3410,4899,5554,6101,8081,9898 /etc/shorewall/blacklist http://shorewall.net/blacklisting_support.htm http://shorewall.net/configuration_file_basics.htm#Pairs shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-hosts(5), shorewall_interfaces(5), shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5), shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5)