shorewall6-zones 5 zones Shorewall6 zone declaration file /etc/shorewall6/zones The /etc/shorewall6/zones file declares your network zones. You specify the hosts in each zone through entries in /etc/shorewall6/interfaces or /etc/shorewall6/hosts. The columns in the file are as follows. ZONE - zone[:parent-zone[,parent-zone]...] Name of the zone. The names "all", "none", "SOURCE" and "DEST" are reserved and may not be used as zone names. The maximum length of a zone name is determined by the setting of the LOGFORMAT option in shorewall6.conf(5). With the default LOGFORMAT, zone names can be at most 5 characters long. The order in which Shorewall6 matches addresses from packets to zones is determined by the order of zone declarations. Where a zone is nested in one or more other zones, you may either ensure that the nested zone precedes its parents in this file, or you may follow the (sub)zone name by ":" and a comma-separated list of the parent zones. The parent zones must have been declared in earlier records in this file. See shorewall6-nesting(5) for additional information. Example: #ZONE TYPE OPTIONS IN OPTIONS OUT OPTIONS a ipv6 b ipv6 c:a,b ipv6 Currently, Shorewall6 uses this information to reorder the zone list so that parent zones appear after their subzones in the list. The IMPLICIT_CONTINUE option in shorewall6.conf(5) can also create implicit CONTINUE policies to/from the subzone. In the future, Shorewall6 may make additional use of nesting information. TYPE ipv6 This is the standard Shorewall6 zone type and is the default if you leave this column empty or if you enter "-" in the column. Communication with some zone hosts may be encrypted. Encrypted hosts are designated using the 'ipsec'option in shorewall6-hosts(5). ipsec Communication with all zone hosts is encrypted. Your kernel and ip6tables must include policy match support. firewall Designates the firewall itself. You must have exactly one 'firewall' zone. No options are permitted with a 'firewall' zone. The name that you enter in the ZONE column will be stored in the shell variable $FW which you may use in other configuration files to designate the firewall zone. bport (or bport6) The zone is associated with one or more ports on a single bridge. OPTIONS, IN OPTIONS and OUT OPTIONS - [option[,option]...] A comma-separated list of options. With the exception of the mss option, these only apply to TYPE ipsec zones. reqid=number where number is specified using setkey(8) using the 'unique:number option for the SPD level. spi=<number> where number is the SPI of the SA used to encrypt/decrypt packets. proto=ah|esp|ipcomp IPSEC Encapsulation Protocol mss=number sets the MSS field in TCP packets. If you supply this option, you should also set FASTACCEPT=No in shorewall6.conf(5) to insure that both the SYN and SYN,ACK packets have their MSS field adjusted. mode=transport|tunnel IPSEC mode tunnel-src=address[/mask] only available with mode=tunnel tunnel-dst=address[/mask] only available with mode=tunnel strict Means that packets must match all rules. next Separates rules; can only be used with strict The options in the OPTIONS column are applied to both incoming and outgoing traffic. The IN OPTIONS are applied to incoming traffic (in addition to OPTIONS) and the OUT OPTIONS are applied to outgoing traffic. If you wish to leave a column empty but need to make an entry in a following column, use "-". /etc/shorewall6/zones http://www.shorewall.net/Multiple_Zones.html. shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall6-interfaces(5), shorewall6-maclist(5), shorewall6-nesting(8), shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5), shorewall6-route_rules(5), shorewall6-routestopped(5), shorewall6-rules(5), shorewall6.conf(5), shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-tcrules(5), shorewall6-tos(5), shorewall6-tunnels(5)