holm/shorewall_code
1
0
Fork 0
forked from extern/shorewall_code
Code Pull Requests Activity
1e7c0d0947
shorewall_code/Shorewall-common/releasenotes.txt
teastep 77be234a24 Add experimental support for IFBs 
git-svn-id: https://shorewall.svn.sourceforge.net/svnroot/shorewall/trunk@8267 fbd18981-670d-0410-9b5c-8dc0c1a9a2bb
2008-03-05 16:16:04 +00:00

549 lines
19 KiB
Plaintext
Raw Blame History

Shorewall 4.1 Patch Release 6.
----------------------------------------------------------------------------
R E L E A S E 4 . 1 H I G H L I G H T S
----------------------------------------------------------------------------
1) Support is included for multiple internet providers through the same
ethernet interface.
2) Support for NFLOG has been added.
3) Enhanced operational logging.
4) The tarball installers now work under Cygwin.
Migration Issues.
1) Previously, when HIGH_ROUTE_MARKS=Yes, Shorewall allowed non-zero
mark values < 256 to be assigned in the OUTPUT chain. This has been
changed so that only high mark values may be assigned
there. Packet marking rules for traffic shaping of packets
originating on the firewall must be coded in the POSTROUTING table.
2) Previously, Shorewall did not range-check the value of the
VERBOSITY option in shorewall.conf. Beginning with Shorewall 4.1:
a) A VERBOSITY setting outside the range -1 through 2 is rejected.
b) After the -v and -q options are applied, the resulting value is
adjusted to fall within the range -1 through 2.
3) Specifying a destination zone in a NAT-only rule now generates a
warning and the destination zone is ignored. NAT-only rules are:
NONAT
REDIRECT-
DNAT-
4) The default value for LOG_MARTIANS has been changed. Previously,
the defaults were:
Shorewall-perl - 'Off'
Shorewall-shell - 'No'
The new default values are:
Shorewall-perl - 'On'
Shorewall-shell - 'Yes'.
Shorewall-perl users may:
a) Accept the new default -- martians will be logged from all
interfaces with route filtering except those with log_martians=0
in /etc/shorewall/interfaces.
b) Explicitly set LOG_MARTIANS=Off to maintain compatibility with
prior versions of Shorewall.
Shorewall-shell users may:
a) Accept the new default -- martians will be logged from all
interfaces with the route filtering enabled.
b) Explicitly set LOG_MARTIONS=No to maintain compatibility with
prior versions of Shorewall.
5) The value of IMPLICIT_CONTINUE in shorewall.conf (and samples) has
been changed from Yes to No.
Problems corrected in 4.1.6.
None.
New Features in 4.1.6.
1) The default value for the IMPLICIT_CONTINUE option has been changed
to 'No'.
2) A REDIRECTED INTERFACES option has been added to the tcdevices file
to support using an IFB (Intermediate Functional Block) device.
IFBs can be used to shape incoming traffic by redirecting that
traffic through the IFB.
To use this feature:
a) Specify the name of your IFB in the INTERFACE column.
b) List the redirected device names (comma-separated) in the
REDIRECTED INTERFACES column.
Packets that are input from the redirected interface(s) will appear
as output packets on the IFB.
This support should be considered EXPERIMENTAL.
New Features in Shorewall 4.1.
1) Shorewall 4.1 contains support for multiple Internet providers
through a single ethernet interface. Configuring two providers
through a single interface differs from two providers through two
interfaces in several ways.
a) Only ethernet (or ethernet-like) interfaces can be used. For
inbound traffic, the MAC addresses of the gateway routers is used
to determine which provider a packet was received through. Note
that only routed traffic can be categorized using this technique.
b) You must specify the address on the interface that corresponds to
a particular provider in the INTERFACE column by following the
interface name with a colon (":") and the address.
c) Entries in /etc/shorewall/masq must be qualified by the provider
name (or number).
d) This feature requires Realm Match support in your kernel and
iptables. If you use a capabilities file, you need to regenerate
the file with Shorewall 4.1 or Shorewall-lite 4.1.
e) You must add route_rules entries for networks that are accessed
through a particular provider.
f) If you have additional IP addresses through either provider,
you must add route_rules to direct traffic FROM each of those
addresses through the appropriate provider.
g) You must add MARK rules for any traffic that you know originates
from a particular provider.
Example:
Providers Blarg (1) and Avvanta (2) are both connected to
eth0. The firewall's IP address with Blarg is 206.124.146.176/24
(gateway 206.124.146.254) and the IP address from Avvanta is
130.252.144.8/24 (gateway 130.252.144.254). We have a second IP
address (206.124.146.177) from Blarg.
/etc/shorewall/providers:
#PROVIDER NUMBER MARK DUPLICATE INTERFACE GATEWAY
Blarg 1 1 main eth0:206.124.146.176 206.124.146.254 ...
Avvanta 2 2 main eth0:130.252.144.8 130.252.144.254 ...
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
eth0(Blarg) 130.252.144.8 206.124.146.176
eth0(Avvanta) 206.124.146.176 130.252.144.8
eth0(Blarg) eth1 206.124.146.176
eth0(Avvanta) eth1 130.252.144.8
/etc/shorewall/route_rules:
#SOURCE DEST PROVIDER PRIORITY
- 206.124.146.0/24 Blarg 1000
- 130.252.144.0/24 Avvanta 1000
206.124.146.177 - Blarg 26000
/etc/shorewall/tcrules
#MARK/CLASSIFY SOURCE DEST
1 eth0:206.124.146.0/24 0.0.0.0/0
2 eth0:130.242.144.0/24 0.0.0.0/0
2) You may now include the name of a table (nat, mangle or filter) in
a 'shorewall refresh' command by following the table name with a
colon (e.g., mangle:). This causes all non-builtin chains in the
table to be reloaded.
Example:
shorewall refresh nat:
3) When no chain name is given to the 'shorewall refresh' command, the
mangle table is refreshed along with the blacklist chain (if
any). This allows you to modify /etc/shorewall/tcrules and install
the changes using 'shorewall refresh'.
4) Support for the NFLOG log target has been added. NFLOG is a
successor to ULOG. In addition, both ULOG and NFLOG may be followed
by a list of up to three numbers in parentheses.
The first number specifies the netlink group (1-32). If omitted
(e.g., NFLOG(,0,10)) then a value of 1 is assumed.
The second number specifies the maximum number of bytes to copy. If
omitted, 0 (no limit) is assumed.
The third number specifies the number of log messages that should
be buffered in the kernel before they are sent to user space. The
default is 1.
Examples:
/etc/shorewall/shorewall.conf:
MACLIST_LOG_LEVEL=NFLOG(1,0,1)
/etc/shorewall/rules:
ACCEPT:NFLOG(1,0,1) vpn fw tcp ssh,time,631,8080
5) Shorewall-perl 4.1 implements an alternative syntax for macro
parameters and for the NFQUEUE queue number. Rather than following
the macro name (or NFQUEUE) with a slash ("/") and the parameter,
the parameter may be enclosed in parentheses.
Examples -- each pair shown below are equivalent:
DNS/ACCEPT DNS(ACCEPT)
NFQUEUE/3 NFQUEUE(3)
The old syntax will still be accepted but will cease to be documented
in some future Shorewall release.
6) Shorewall 4.1 contains enhanced operational logging capabilities
through a set of related enhancements to Shorewall-common and
Shorewall-perl. The enhancements are not supported by
Shorewall-shell nor are they supported by Shorewall-lite except
when the script is compiled using Shorewall-perl.
a) The STARTUP_LOG option in /etc/shorewall/shorewall.conf gives
the name of the Shorewall operational log. The log will be
created if it does not exist.
b) The LOG_VERBOSITY option in /etc/shorewall/shorewall.conf gives
the verbosity at which logging will occur. It uses the same
value range as VERBOSITY:
-1 Do not log
0 Almost quiet
1 Only major steps
2 Verbose
c) An absolute VERBOSITY may be specified on the command line
using the -v option followed by -1,0,1 or 2.
Example:
shorewall -v2 check
d) The /etc/init.d/shorewall script supplied with the
shorewall.net packages sets '-v0' as the default. This may be
overridden with the OPTIONS setting in /etc/defaults/shorewall or
/etc/sysconfig/shorewall.
Logging occurs on both Shorewall-perl and the generated script when
the following commands are issued:
start
restart
refresh
Messages in the log are always timestamped.
This change implemented two new options to the Shorewall-perl
compiler (/usr/share/shorewall-perl/compiler.pl).
--log=<logfile>
--log_verbosity={-1|0-2}
The --log option is ignored when --log_verbosity is not supplied or
is supplied with value -1.
To avoid a proliferation of parameters to
Shorewall::Compiler::compile(), that function has been changed to
use named parameters. Parameter names are:
object Object file. If omitted or '', the
configuration is syntax checked.
directory Directory. If omitted or '', configuration
files are located using
CONFIG_PATH. Otherwise, the directory named by
this parameter is searched first.
verbosity Verbosity; range -1 to 2
timestamp 0|1 -- timestamp messages.
debug 0|1 -- include stack trace in warning/error
messages.
export 0|1 -- compile for export.
chains List of chains to be reloaded by 'refresh'.
log File to log compiler messages to.
log_verbosity Log Verbosity; range -1 to 2.
Those parameters that are supplied must have defined values.
Defaults are:
object '' ('check' command)
directory ''
verbosity 1
timestamp 0
debug 0
export 0
chains ''
log ''
log_verbosity -1
Example:
use lib '/usr/share/shorewall-perl/';
use Shorewall::Compiler;
compiler( object => '/root/firewall',
log => '/root/compile.log',
log_verbosity => 2 );
7) Previously, when HIGH_ROUTE_MARKS=Yes, Shorewall allowed non-zero
mark values < 256 to be assigned in the OUTPUT chain. This has been
changed so that only high mark values may be assigned
there. Packet marking rules for traffic shaping of packets
originating on the firewall must be coded in the POSTROUTING chain.
8) Previously, Shorewall did not range-check the value of the
VERBOSITY option in shorewall.conf. Beginning with Shorewall 4.1:
a) A VERBOSITY setting outside the range -1 through 2 is rejected.
b) After the -v and -q options are applied, the resulting value is
adjusted to fall within the range -1 through 2.
9) The tcdevices file has been extended to include an OPTIONS
column. Currently only a single option is defined.
classify When specified, you must use explicit CLASSIFY tcrules
to classify traffic by class. Shorewall will not create
any CLASSIFY rules to classify traffic by mark value.
The 'classify' option should be specified when you want to do all
classification using CLASSIFY tcrules. Because CLASSIFY is not a
terminating target, every packet passes through all CLASSIFY
rules. 'classify' can prevent packets from having to pass through
useless additional rules.
Example:
/etc/shorewall/tcdevices
#INTERFACE IN-BANDWITH OUT-BANDWIDTH OPTIONS
$EXT_IF 1300kbit 384kbit classify
/etc/shorewall/tcclasses
#INTERFACE MARK RATE CEIL PRIORITY OPTIONS
$EXT_IF 10 5*full/10 full 1 tcp-ack,tos-minimize-delay
$EXT_IF 20 2*full/10 6*full/10 2 default
$EXT_IF 30 2*full/10 6*full/10 3
/etc/shorewall/tcrules
#MARK SOURCE DEST PROTO PORT(S) SOURCE
# PORT(S)
1:110 192.168.0.0/22 $EXT_IF
1:130 206.124.146.177 $EXT_IF tcp - 873
This example shows my own simple traffic shaping configuration. I
have three classes; one for traffic from our local network, one for
rsync from the master shorewall.net server, and one for all other
DMZ traffic. I use CLASSIFY rules to assign traffic to the first
and third class and let the rest default to the second class.
10) COMMENT lines are now supported in macro bodies by Shorewall-perl
and are ignored by the Shorewall-shell compiler.
COMMENT lines in macros work slightly differently from COMMENT
lines in other files. COMMENT lines in macros are ignored if
COMMENT support is not available or if there was a COMMENT in use
when the top-level macro was invoked. This allows the
following:
/etc/shorewall/macro.SSH:
#ACTION SOURCE PROTO DEST SOURCE RATE USER/
# PORT(S) PORT(S) LIMIT GROUP
COMMENT My SSH Macro
PARAM - - tcp 22
/etc/shorewall/rules:
COMMENT Allow SSH from home
SSH/ALLOW net:$MYIP $FW
COMMENT
The comment line in macro.SSH will not override the
COMMENT line in the rules file and the generated rule will show
/* Allow SSH from home */
when displayed through the Shorewall show and dump commands.
If a macro is invoked and there is no current comment, then the
name of the macro automatically becomes the current comment. This
makes macros self-commenting.
11) If the program named in SHOREWALL_SHELL doesn't exist or is not
executable, Shorewall and Shorewall-lite now both fall back to
/bin/sh after issuing a warning message. Previously, both
terminated with a fatal error.
12) Shorewall-perl now generates fatal error conditions if there are
no IPv4 zones defined or there are no interfaces defined.
13) Shorewall now unconditionally uses tc filter rules to classify
traffic by MARK value. Previously, Shorewall used the CLASSIFY
target in the POSTROUTING chain if it was available.
14) The Shorewall-common installer (install.sh) now works on Windows
under Cygwin.
To install Shorewall-perl under Cygwin:
$ tar -zxf shorewall-perl-4.x.y.tar.bz2
$ tar -zxf shorewall-common-4.x.y.tar.bz2
$ cd shorewall-perl-4.x.y
$ USER=<your user id> GROUP=None ./install.sh
$ cd ../shorewall-common-4.x.y
$ USER=<your user id> GROUP=None ./install.sh
The 'shorewall' program is installed in /bin/ (a.k.a, /usr/bin/).
15) When installing on Cygwin, /etc/shorewall is no longer fully
populated. Rather, only the shorewall.conf and params files are
installed. As always, the full configuration file set is installed
in /usr/share/shorewall/configfiles.
16) Specifying a destination zone in a NAT-only rule now generates a
warning and the destination zone is ignored. NAT-only rules are:
NONAT
REDIRECT-
DNAT-
17) The /etc/shorewall/masq and /etc/shorewall/nat file now accept a
comma-separated list of interface names where before only a single
interface name could be listed (Shorewall-perl only).
This feature is not for beginners. It iterates over the
list of interfaces, substituting each interface in place of the
list and processing the resulting entry according to the semantics
of earlier Shorewall versions. If you don't know where to use this,
don't try.
Example 1:
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
eth0,eth1 eth2 1.2.3.4
equivalent to:
#INTERFACE SOURCE ADDRESS
eth0 eth2 1.2.3.4
eth1 eth2 1.2.3.4
Example 2:
/etc/shorewall/masq:
#INTERFACE SOURCE ADDRESS
eth0,eth1::192.168.1.0/24 eth2 1.2.3.4
equivalent to:
#INTERFACE SOURCE ADDRESS
eth0::192.168.1.0/24 eth2 1.2.3.4
eth1::192.168.1.0/24 eth2 1.2.3.4
Example 3:
/etc/shorewall/nat:
#EXTERNAL INTERFACE INTERNAL
206.124.146.178 eth0,wlan0 192.168.1.3
equivalent to:
#EXTERNAL INTERFACE INTERNAL
206.124.146.178 eth0 192.168.1.3
206.124.146.178 wlan0 192.168.1.3
18) Previously, the INTERFACE name used in the masq, nat and netmap
files had to exactly match the name of an interface from the
interfaces file. Beginning with Shorewall-perl 4.1.4, the
interface may loosely match a wildcard entry in the interfaces
file.
Example:
/etc/shorewall/interfaces:
vpn tun+
/etc/shorewall/masq:
tun1 192.168.4.0/24
19) Previously, Shorewall classified non-firewall zones as either
'simple' or 'complex'. Attributes of a zone which made it 'complex'
included:
- The zone was of type 'ipsec' or 'ipsec4' or it had a hosts
entry with the 'ipsec' options.
- The zone had OPTIONS, IN OPTIONS or OUT OPTIONS
- The zone had more than one network on a given interface
- The zone had a hosts file entry with an exclusion.
- The zone had a hosts file entry specifying an ipset.
The handling of 'simple' and 'complex' zones was different.
- complex zones had their own 'forward' chain (named
'<zone>_frwd').
- complex zones with exclusions had their own 'input' and
'output' chains.
Beginning with Shorewall-perl 4.1, all non-firewall zones will be
treated as 'complex'. This will have the effect of one additional
filter chain per zone but in most cases, the average number of
filter rules traversed by a connection request will be reduced.
20) The need for interface-specific chains (such as eth0_in, eth4_fwd,
etc.) in the filter table has been drastically reduced. This has
the effect of reducing the average number of rules that each packet
must traverse.
21) The default value for LOG_MARTIANS is now 'Yes' ('On' in
Shorewall-perl). Previously, the default value was 'No' ('Off' in
Shorewall-perl). The shorewall.conf file has also been
updated to specify a value of 'Yes' (which is interpreted as 'On'
by Shorewall-perl).
22) Shorewall-perl now generates an error when a MAC address appears in
a traffic shaping rule in the OUTPUT or POSTROUTING chains.
23) Macros are now self-commenting under control of a new AUTO_COMMENT
option in shorewall.conf. When this option is set, if there is not
a current comment when a macro is invoked, the behavior under
Shorewall-perl is as if the first line of the macro file was
"COMMENT <macro name>".
So, if you have this rule:
SSH/ACCEPT loc fw
then the generated netfilter rule will include "/* SSH */" when
viewed with 'iptables -L' or 'shorewall show loc2fw' or 'shorewall
dump'.
The AUTO_COMMENT option has a default value of 'Yes' and is only
available under Shorewall-perl The option is ignored by
Shorewall-shell.
View Git Blame Copy Permalink